Zte ZXR10 5900E Series Configuration Manual page 188

ZXR10 5900E Series Configuration Guide (IPv4 Routing)
S4(config-if-vlan2)#exit
S4(config)#router bgp 2
S4(config-bgp)#redistribute connected
S4(config-bgp)#redistribute static
S4(config-bgp)#network 10.1.1.0 255.255.255.0
S4(config-bgp)#aggregate-address 192.168.0.0 255.255.252.0 count 0 as-set
S4(config-bgp)#neighbor 1.1.1.2 remote-as 1
S4(config-bgp)#neighbor 1.1.1.2 activate
S4(config-bgp)#neighbor 1.1.1.2 ebgp-multihop ttl 5
S4(config-bgp)#neighbor 1.1.1.2 route-map test-static out
S4(config-bgp)#neighbor 1.1.1.2 send-med
S4(config-bgp)#neighbor 1.1.1.2 update-source loopback1
S4(config-bgp)#exit
S4(config)#ip route 1.1.1.2 255.255.255.255 11.1.1.2
S4(config)#ip route 192.168.100.0 255.255.255.0 10.1.1.2
S4(config)#ip route 192.168.1.0 255.255.255.0 10.1.1.2
S4(config)#ip route 192.168.0.0 255.255.255.0 10.1.1.2
S4(config)#ip route 192.168.3.0 255.255.255.0 10.1.1.2
S4(config)#ip route 192.168.2.0 255.255.255.0 10.1.1.2
S4(config)#ipv4-access-list 1
S4(config-ipv4-acl)#rule 1 permit 192.168.0.0 0.0.3.255
S4(config-ipv4-acl)#rule 2 permit 10.1.1.0 0.0.0.255
S4(config-ipv4-acl)#exit
S4(config)#route-map test-static permit 10
S4(config-route-map)#match ip address 1
S4(config-route-map)#set ip metric 33
S4(config-route-map)#exit
Run the following commands on S5:
S5(config)#interface loopback1
S5(config-if-loopback1)#ip address 1.1.1.5 255.255.255.255
S5(config-if-loopback1)#exit
S5(config)#interface null1
S5(config-if-null1)#exit
S5(config)#interface vlan1
S5(config-if-vlan1)#ip address 20.1.1.1 255.255.255.0
S5(config-if-vlan1)#exit
S5(config)#interface vlan2
S5(config-if-vlan2)#ip address 20.1.2.1 255.255.255.0
S5(config-if-vlan2)#negotiation auto
S5(config-if-vlan2)#exit
S5(config)#router ospf 1
S5(config-ospfv2)#network 14.1.1.0 0.0.0.3 area 0.0.0.0
S5(config-ospfv2)#network 20.1.1.0 0.0.0.255 area 0.0.0.0
S5(config-ospfv2)#exit
5-64
SJ-20150114102049-003|2015-01-15 (R1.0) ZTE Proprietary and Confidential