Zte ZXR10 5900E Series Configuration Manual
  1. Manuals
  2. Brands
  3. Zte Manuals
  4. Switch
  5. ZXR10 5900E Series
  6. Configuration manual
Zte ZXR10 5900E Series Configuration Manual

Zte ZXR10 5900E Series Configuration Manual

Easy-maintenance mpls routing switch
Hide thumbs Also See for ZXR10 5900E Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Configuration Manual, Instruction Manual
ZXR10 5900E Series
Easy-Maintenance MPLS Routing Switch
Configuration Guide (Multicast)
Version: 3.00.11
ZTE CORPORATION
No. 55, Hi-tech Road South, ShenZhen, P.R.China
Postcode: 518057
Tel: +86-755-26771900
Fax: +86-755-26770801
URL: http://support.zte.com.cn
E-mail: support@zte.com.cn

Advertisement

Table of Contents
loading

Related Manuals for Zte ZXR10 5900E Series

Summary of Contents for Zte ZXR10 5900E Series

  • Page 1 ZXR10 5900E Series Easy-Maintenance MPLS Routing Switch Configuration Guide (Multicast) Version: 3.00.11 ZTE CORPORATION No. 55, Hi-tech Road South, ShenZhen, P.R.China Postcode: 518057 Tel: +86-755-26771900 Fax: +86-755-26770801 URL: http://support.zte.com.cn E-mail: support@zte.com.cn...
  • Page 2 ZTE CORPORATION is prohibited. Additionally, the contents of this document are protected by contractual confidentiality obligations. All company, brand and product names are trade or service marks, or registered trade or service marks, of ZTE CORPORATION or of their respective owners.

  • Page 3: Table Of Contents

    4.4.3 Illegal Multicast Source Control ............... 4-18 Chapter 5 PIM-SSM Configuration ............5-1 5.1 PIM-SSM Overview .................... 5-1 5.2 Configuring PIM-SSM ..................5-1 5.3 PIM-SSM Configuration Example ................ 5-2 Chapter 6 PIM-DM Configuration .............. 6-1 6.1 PIM-DM Overview ....................6-1 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 4 10.4 MSDP Configuration Example ................. 10-8 Chapter 11 Static Multicast Configuration ..........11-1 11.1 Static Multicast Overview .................11-1 11.2 Configuring Static Multicast ................11-2 11.3 Static Multicast Maintenance ................11-3 11.4 Static Multicast Configuration Example .............11-4 Figures......................I Glossary ......................III SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 5: About This Manual

    About This Manual Purpose This manual is the ZXR10 5900E Series (V3.00.11) Easy-Maintenance MPLS Routing Switch Configuration Guide (Multicast), which is applicable to the ZXR10 5900E (V3.00.11) series switches. Intended Audience This manual is intended for: Network planning engineer Debugging engineer...
  • Page 6 Constant Text that you type, program codes, filenames, directory names, and function names. width Optional parameters. Mandatory parameters. Separates individual parameter in series of parameters. Note: provides additional information about a certain topic. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 7: Multicasting Overview

    It determines a unique forwarding path between the subnet to which the multicast source belongs and all the subnets that contain group members. There are two types of multicast trees: source tree and shared tree. Source tree SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 8 ZXR10 5900E Series Configuration Guide (Multicast) The source tree is also called the Shortest Path Tree (SPT). It constructs a spanning tree to all receivers for each source. This spanning tree uses the source as the root node. It reaches the subnets to which the receivers belong. A multicast group may contain several multicast sources.

  • Page 9: Configuring Public Ip Multicast

    [vrf <vrf-name>] Displays the number of ZXR10# multicast routes in the IP multicast routing tables. show ip mroute brief [vrf <vrf-name>] Displays the brief information ZXR10# of an IP multicast routing table. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 10 ZXR10 5900E Series Configuration Guide (Multicast) Step Command Function mtrace <source-address>[<dest-address>][<group- Traces the reverse path of the ZXR10# source. address>] Enables the multicast damping damping-enable ZXR10(config-mcast)# function. no damping-enable Disables the multicast damping ZXR10(config-mcast)# function. damping-threshold < threshold> Configures the threshold for...
  • Page 11 It is recommended that you configure the [interface <interface-name>] parameter. If the parameter is not configured, this command is invalid, and multicast traffic is blocked no matter whether SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 12 ZXR10 5900E Series Configuration Guide (Multicast) Step Command Function the monitoring interface is configured. Deletes a multicast monitoring no monitor-mroute ZXR10(config-mcast)# <source-address><group-address>[interface route. <interface-name>] mroute-limit <limit> Configures the limit number ZXR10(config-mcast)# of items in the multicast forwarding table. Default: the maximum number supported by the system.
  • Page 13 <group-address> Group address, in dotted decimal notation. <source-address> Source address, in dotted decimal notation. summary Summary information. <interface-name> Interface name. For a description of the parameter in Step 9, refer to the following table: SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 14 ZXR10 5900E Series Configuration Guide (Multicast) Parameter Description <destination-address> Destination address. For a description of the parameter in Step 16, refer to the following table: Parameter Description <threshold> Damping threshold. For a description of the parameters in Step 18, refer to the following table:...

  • Page 15: Chapter 2 Igmp Configuration

    The IGMP provides information that is necessary when packets are forwarded to the destination (the last stage). Multicast switches and hosts that receive multicast data exchange information. The information is collected from the group members of the hosts that are directly connected to multicast switches. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 16: Configuring Igmp

    ZXR10 5900E Series Configuration Guide (Multicast) The IGMP uses two types of packets, group member query packets and group member report packets. A multicast switch periodically sends group member query packets to all hosts to know whether specific group members exist in the connected subnets.
  • Page 17 At present, there are IGMP v1, v2 and v3. By default, IGMP v2 is used. The version can be adjusted using the version <version> command. For security, a switch requires that all NEs on the same segment use the same IGMP version, the IGMP v1,v2 or v3. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 18 ZXR10 5900E Series Configuration Guide (Multicast) The configuration of the IGMP version is based on the interface. Different versions can be configured on different interfaces. Configure an IGMP Group on an Interface To configure an IGMP group on an interface of the ZXR10 5900E, perform the following...
  • Page 19 The timers related to the querier can be adjusted as required. To configure IGMP timers on the ZXR10 5900E, perform the following steps: SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 20: Maintaining Igmp

    ZXR10 5900E Series Configuration Guide (Multicast) Step Command Function Sets the IGMP query interval. quer ZXR10(config-mcast-igmp-if-interface-name)# y-interval <seconds> <seconds>: range: 1-65535 seconds, default: 125 seconds. Sets the maximum response query ZXR10(config-mcast-igmp-if-interface-name)# -max-response-time <seconds> time contained in the query messages. <seconds>: range: 1-25 seconds, default: 10 seconds.
  • Page 21 IGMP immediate leave control is not set IGMP shaping packets number is not set IGMP maximum joins is not set The following is sample output from the show ip igmp groups {[<interface-name>]|[<group-a ddr>]}[detail] command: ZXR10#show ip igmp groups loopback3 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 22: Igmp Configuration Examples

    ZXR10 5900E Series Configuration Guide (Multicast) Total: 2 groups joined in loopback3 Group addr Interface Present Expire Last Reporter 225.0.0.1 loopback3 2d20h never 200.1.1.3 226.1.1.1 loopback3 2d20h never 200.1.1.3 For a description of the parameters in the execution result, refer to the following table:...
  • Page 23 IGMP maximum joins is not set Run the show ip igmp interface command to check the configuration result on S2. S2#show ip igmp interface vlan2 vlan2 Internet address is 10.0.0.2, subnet mask is 24 IGMP is enabled on interface SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 24: Joining Of Igmp Dynamic Group And Static Group

    ZXR10 5900E Series Configuration Guide (Multicast) Current IGMP version is 2 /*IGMP version information*/ IGMP query interval is 125 seconds /*Query interval*/ IGMP last member query interval is 1 seconds /*Last member query interval*/ IGMP query max response time is 10 seconds...
  • Page 25 S1(config-mcast-igmp-if-vlan1)#show ip igmp groups detail Flags: S - Static Group, SSM - SSM Group, M - MDT Group Interface: vlan1 Group: 225.1.1.1 Flags: Uptime: 00:05:12 Group mode: EXCLUDE (Expires: 00:03:24) Last reporter: 100.17.21.2 2-11 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 26: Igmp Fast Leaving From All Groups

    ZXR10 5900E Series Configuration Guide (Multicast) Group source list is empty 2.4.3 IGMP Fast Leaving From All Groups Configuration Description Figure 2-3 shows the network topology. A switch is connected to a multicast user directly. Figure 2-3 IGMP Fast Leaving From All Groups Configuration Flow 1.

  • Page 27: Igmp Fast Leaving From A Specified Group

    Figure 2-4 IGMP Fast Leaving From a Specified Group Configuration Flow 1. Configure a group filter rule. 2. Enter multicast configuration mode and enable the interface IGMP function. 3. Configure fast leaving from a specified group on the interface. 2-13 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 28 ZXR10 5900E Series Configuration Guide (Multicast) Configuration Commands The configuration commands of S1 are as follows: S1(config)#ipv4-access-list groupfilter S1(config-ipv4-acl)#rule 1 permit 225.0.0.0 S1(config-ipv4-acl)#rule 2 deny any S1(config-ipv4-acl)#exit S1(config)#ip multicast-routing S1(config-mcast)#router pim S1(config-mcast-pim)#interface vlan1 S1(config-mcast-pim-vlan1)#pimsm S1(config-mcast-pim-vlan1)#exit S1(config-mcast-pim)#exit S1(config-mcast)#router igmp S1(config-mcast-igmp)#interface vlan1...
  • Page 29 : Send IGMPv2 specific query(225.0.0.1) on vlan1 ZXR10 PFU-0/20/0 2010-7-27 09:58:34 igmp : Send IGMPv2 specific query(225.0.0.1) on vlan1 ZXR10 PFU-0/20/0 2010-7-27 09:58:35 igmp : Delete group 225.0.0.1 on vlan1 ZXR10#show ip igmp groups 2-15 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 30 ZXR10 5900E Series Configuration Guide (Multicast) Total: 0 groups Group addr Interface Present Expire Last Reporter ZXR10# 2-16 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 31: Chapter 3 Igmp Snooping Configuration

    ZXR10(config-igmpsnoop)# {igmpv1 | igmpv2 | igmpv3}{accept | discard | ignore} packets of different versions in global IGMP snooping configuration mode. Sets a querier in global IGMP igmp snooping querier ZXR10(config-igmpsnoop)# snooping configuration mode. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 32 ZXR10 5900E Series Configuration Guide (Multicast) Step Command Function Sets the querier interval igmp snooping query-interval ZXR10(config-igmpsnoop)# <interval> in global IGMP snooping configuration mode. <interval>: interval of sending query packets, range: 30–65535 seconds, default: 125 seconds. Sets the maximum response...
  • Page 33 <ip-address>: address of a host, in the dotted decimal notation. Sets a static member igmp snooping ZXR10(config-igmpsnoop-vpls-zte)# static <ip-address> interface <port-name> of a multicast group in a VPLS instance in IGMPSNOOP-VPLS configuration mode. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 34 ZXR10 5900E Series Configuration Guide (Multicast) Step Command Function Sets the aging time of a igmp snooping ZXR10(config-igmpsnoop-vpls-zte)# host-time-out <time> multicast group member in a VPLS instance in IGMPSNOOP-VPLS configuration mode. <time>: aging time, range: 30–65535 seconds, default: 260 seconds.
  • Page 35 VLAN in IGMPSNOOP-VLAN configuration mode. <ip-address>: host address, in the dotted decimal notation. Sets a multicast static igmp snooping static ZXR10(config-igmpsnoop-vlan1)# <ip-address> interface<port-name> member for a VLAN in IGMPSNOOP-VLAN configuration mode. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 36 ZXR10 5900E Series Configuration Guide (Multicast) Step Command Function Sets the aging time of a igmp snooping ZXR10(config-igmpsnoop-vlan1)# host-time-out <time> multicast group member for a VLAN in IGMPSNOOP-VLAN configuration mode. <time>: host aging time, range: 30–65535 seconds, default: 260 seconds.

  • Page 37: Maintaining Igmp Snooping

    Operating mode of the IGMP snooping function. 3.3 Maintaining IGMP Snooping To maintain the IGMP snooping function on the ZXR10 5900E, run the following commands. Command Function show ip igmp snooping Displays all IGMP snooping ZXR10(config)# entries. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 38 ZXR10 5900E Series Configuration Guide (Multicast) Command Function show ip igmp snooping vlan <vlan-id> Displays information about the ZXR10(config)# configuration and all multicast entries of a VLAN. show ip igmp snooping vpls <vpls-name> Displays information about the ZXR10(config)# configuration and all multicast entries of a VPLS.
  • Page 39 Time -------------------------------------------------------- gei-0/1/1/2 Static V2Query 65535 gei-0/1/1/1 Static V2Query 65535 ZXR10(config)# For a description of the parameters in the execution result, refer to the following table: Parameter Description Index Serial number of an entry. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 40: Igmp Snooping Configuration Example

    ZXR10 5900E Series Configuration Guide (Multicast) Parameter Description VLAN VLAN instance ID of an entry. VPNID VPLS instance ID of an entry. Port Routing port. State State of a routing port. Version Type of IGMP packets processed by a routing port by default.

  • Page 41: Figure 3-1 Igmp Snooping In A Vlan Instance

    Simulate the hosts to join multicast group 225.0.0.1 on gei-0/1/1/2 and gei-0/1/1/4. Configuration Commands Configuration of router A: SwitchA(config)#interface gei-0/1/1/2 RouterA(config-if-gei-0/1/1/2)#ip address 10.0.0.1 255.255.255.0 RouterA(config-if-gei-0/1/1/2)#exit RouterA(config)#ip multicast-routing RouterA(config-mcast)#router pim RouterA(config-mcast-pim)#interface gei-0/1/1/2 RouterA(config-mcast-pim-if-gei-0/1/1/2)#pimsm RouterA(config-mcast-pim-if-gei-0/1/1/2)#exit RouterA(config-mcast-pim)#exit 3-11 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 42 ZXR10 5900E Series Configuration Guide (Multicast) RouterA(config-mcast)#router igmp RouterA(config-mcast)#router igmp RouterA(config-mcast-igmp-gei-0/1/1/2)#interface gei-0/1/1/2 RouterA(config-mcast-igmp-if-gei-0/1/1/2)#version 2 RouterA(config-mcast-igmp-if-gei-0/1/1/2)#exit RouterA(config-mcast-igmp)#exit RouterA(config-mcast)#exit RouterA(config)# RouterA(config)#interface gei-0/1/1/1 RouterA(config-if-gei-0/1/1/1)#ip address 1.1.1.2 255.255.255.0 RouterA(config-if-gei-0/1/1/1)#exit RouterA(config)#ip multicast-routing RouterA(config-mcast)#router pim RouterA(config-mcast-pim)#interface gei-0/1/1/1 RouterA(config-mcast-pim-if-gei-0/1/1/1)#pimsm RouterA(config-mcast-pim-if-gei-0/1/1/1)#exit RouterA(config-mcast-pim)#exit RouterA(config-mcast)#exit RouterA(config)# Configuration of switch A:...
  • Page 43 Check the detailed information about the IGMP snooping groups in VLAN 10 on switch A as follows: SwitchA(config)#show ip igmp snooping port-info vlan 10 Index VLAN Source Group State Time Ports ----------------------------------------------------------------- 0.0.0.0 225.0.0.1 V2Report 998 gei-0/1/1/2 0.0.0.0 225.0.0.1 V2Report 996 gei-0/1/1/4 SwitchA(config)# 3-13 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 44 ZXR10 5900E Series Configuration Guide (Multicast) This page intentionally left blank. 3-14 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 45: Chapter 4 Pim-Sm Configuration

    RP with the highest priority will become the formal RP. In the PIM-SMv2, some PIM-SM switches are manually set to operate as candidate Bootstrap Routers (BSRs). The candidate BSR with the highest priority will be elected as the formal BSR. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 46 ZXR10 5900E Series Configuration Guide (Multicast) The BSR is responsible for collecting the candidate RP information on the multicast switches in the group to find out the candidate RPs in the multicast domain. It notifies the candidate RPs to all the PIM switches in the PIM domain in a unified way. The PIM switches elect a formal RP from the candidate RP set according to rules the same as that of RP election.

  • Page 47: Configuring Pim-Sm

    Deletes a PIM-SM interface. ZXR10(config-mcast-pim)# bsr-candidate <interface-na Sets a candidate BSR. ZXR10(config-mcast-pim)# me>{[ hash-mask-length <hash-mask-length>],[priority <priority>]} Deletes a candidate BSR. no bsr-candidate ZXR10(config-mcast-pim)# rp-candidate <interface-name Sets a candidate RP. ZXR10(config-mcast-pim)# >{[group-list < prefix-list-name >],[priority <priority>]} SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 48 ZXR10 5900E Series Configuration Guide (Multicast) Step Command Function Deletes a candidate RP. no rp-candidate ZXR10(config-mcast-pim)# <interface-name> Sets switchover of the SPT. spt-threshold infinity ZXR10(config-mcast-pim)# [group-list < access-list-name >] The threshold is infinity. no spt-threshold Deletes switchover from RPT ZXR10(config-mcast-pim)# to SPT.
  • Page 49 Join/Prune messages are dropped. register-source Configures the source address ZXR10(config-mcast-pim)# <interface-name> of register messages. Restores the default source no register-source ZXR10(config-mcast-pim)# address of register messages, meaning the next hop of the unicast route to the source. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 50 ZXR10 5900E Series Configuration Guide (Multicast) Step Command Function Enables PIM-SM on an pimsm ZXR10(config-mcast-pim-if-interface-name)# interface. Disables PIM-SM on an ZXR10(config-mcast-pim-if-interface-name)# interface. pimsm pimdm Enables PIM-DM on an ZXR10(config-mcast-pim-if-interface-name)# interface. Disables PIM-DM on an ZXR10(config-mcast-pim-if-interface-name)# pimdm interface. Sets the DR priority on a PIM...

  • Page 51: Maintaining Pim-Sm

    [<interface-name>] Displays the neighbor information ZXR10# of a PIM-SM interface. show ip pim nexthop [dest-address <ip-address>] Displays the PIM-SM next hop ZXR10# information. show ip pim bfd [<interface-name>] Displays PIM-SM information. ZXR10# SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 52 ZXR10 5900E Series Configuration Guide (Multicast) Command Function show ip pim traffic [<interface-name>] Displays PIM-SM traffic statistic ZXR10# information. clear ip pim traffic [<interface-name>] Clears PIM-SM traffic statistic ZXR10# information. For a description of the parameters, refer to the following table:...
  • Page 53 Uptime: 00:00:09, BSR Priority :0, Hash mask length:30 Expires:00:00:51 This system is a candidate BSR! candidate BSR address: 1.1.1.1(loopback1), priority: 0, hash mask length: 30 This system is a candidate RP! candidate RP address: 1.1.1.1(loopback1),priority:99 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 54 ZXR10 5900E Series Configuration Guide (Multicast) For a description of the parameters in the execution result, refer to the following table: Parameter Description BSR address IP address of the BSR. Uptime Uptime of the BSR. BSR Priority Priority of the BSR.
  • Page 55 Interface name. DR Priority DR priority of the neighbor. Uptime Uptime of the neighbor. Expires Expiring time of the neighbor. Version. The following is sample output from the show ip pim nexthop command: 4-11 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 56 ZXR10 5900E Series Configuration Guide (Multicast) ZXR10#show ip pim nexthop PIM Nexthop Table Nexthop state: R- Nexthop to RP,S- Nexthop to Source, O- Related with Unicast,U- No Unicast Route, L- Local Route,C- Connect to Dest, Dest:2.2.2.2 (00:00:56) Type:.R. .O. .L.
  • Page 57 Number of Grafting messages. Grf-ack Number of Grafting ACK messages. C-RP-Ad Number of CRP report messages. Sta-ref Number of State refreshing messages. The following is sample output from the clear ip pim traffic command: 4-13 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 58: Pim-Sm Configuration Examples

    ZXR10 5900E Series Configuration Guide (Multicast) ZXR10#clear ip pim traffic ZXR10#show ip pim traffic PIM packet receive: Interface Reg-st Grf-ack C-RP-Ad Sta-ref vlan1 PIM packet send: Interface Reg-st Grf-ack C-RP-Ad Sta-ref vlan1 Total traffic in current PIM instance: Summary_pkt Reg-st...
  • Page 59 S2(config-mcast-pim-if-vlan2)#dr-priority 20 S2(config-mcast-pim-if-vlan2)#exit S2(config-mcast-pim)#interface loopback5 S2(config-mcast-pim-if-loopback5)#pimsm S2(config-mcast-pim-if-loopback5)#exit S2(config-mcast-pim)#exit S2(config-mcast)#exit S2(config)#ip route 33.1.1.0 255.255.255.0 199.1.1.1 Configuration Verification Use the show ip pim interface command on S1 to check the interface state, as shown below. 4-15 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 60 ZXR10 5900E Series Configuration Guide (Multicast) S1(config)#show ip pim interface Address Interface State Nbr Hello Mode Count Period Priority Silent 33.1.1.1 vlan2 33.1.1.1 Disabled 199.1.1.1 vlan1 199.1.1.2 Disabled Use the show ip pim neighbor command on S1 to check the neighbor state, as shown below.

  • Page 61: Forwarding Multicast Flow Through Pim-Sm (Static Rp)

    S1(config-mcast)#router pim S1(config-mcast-pim)#interface vlan1 S1(config-mcast-pim-if-vlan1)#pimsm S1(config-mcast-pim)#interface vlan2 S1(config-mcast-pim-if-vlan2)#pimsm S1(config-mcast-pim-if-vlan2)#dr-priority 20 S1(config-mcast-pim)#exit S1(config-mcast-pim)#static-rp 5.5.5.35 S1(config-mcast-pim)#static-rp override S1(config-mcast-pim)#exit S1(config)#ip route 5.5.5.35 255.255.255.255 199.1.1.2 The configuration of S2: S2(config)#ip multicast-routing S2(config-mcast)#router pim S2(config-mcast-pim)#static-rp 5.5.5.35 S2(config-mcast-pim)#static-rp override 4-17 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 62: Illegal Multicast Source Control

    ZXR10 5900E Series Configuration Guide (Multicast) S2(config-mcast-pim)#interface vlan1 S2(config-mcast-pim-if-vlan1)#pimsm S2(config-mcast-pim-if-vlan1)#exit S2(config-mcast-pim)#interface vlan2 S2(config-mcast-pim-if-vlan2)#pimsm S2(config-mcast-pim-if-vlan2)#dr-priority 20 S2(config-mcast-pim-if-vlan2)#exit S2(config-mcast-pim)#interface loopback5 S2(config-mcast-pim-if-vlan2)#pimsm S2(config-mcast-pim-if-vlan2)#exit S2(config-mcast-pim)#exit S2(config-mcast)#exit S2(config)#ip route 33.1.1.0 255.255.255.0 199.1.1.1 Configuration Verification Use the show ip pim interface command on S1 to check the interface state, as shown below.

  • Page 63: Figure 4-3 Illegal Multicast Source Control

    Configure IP addresses on the interfaces of S1 and S2 according to the following table to ensure the IP connectivity on the network. Switch Interface IP Address Mask vlan1 172.1.3.44 255.255.255.0 vlan2 172.2.3.44 255.255.255.0 vlan3 172.3.3.44 255.255.255.0 vlan4 172.1.7.44 255.255.255.0 4-19 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 64 ZXR10 5900E Series Configuration Guide (Multicast) Switch Interface IP Address Mask loopback63 44.63.1.1 255.255.255.255 vlan2 172.1.5.46 255.255.255.0 vlan1 172.1.7.46 255.255.255.0 loopback63 46.63.1.1 255.255.255.255 Configure a multicast protocol on S1 and S2 to establish a multicast tree from the source to the user. Here take PIM-SM as an example.
  • Page 65 (172.3.3.49, 234.254.254.255), RP: 46.63.1.1, TYPE: DYNAMIC, FLAGS: Incoming interface: vlan3, flags: Outgoing interface list: (172.1.3.49, 234.255.255.255), RP: 46.63.1.1, TYPE: DYNAMIC, FLAGS: Incoming interface: vlan1, flags: Outgoing interface list: Vlan4, flags: F/S The multicast routes on S2 are shown below. 4-21 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 66 ZXR10 5900E Series Configuration Guide (Multicast) S2#show ip mroute IP Multicast Routing Table Flags:NS:SPT upsend, RT:Reg upsend, MT:tunnel, F:Forward, S:Syn mrt, NTP:NTP join, FLT:Flt add, FD:Flt del, DPU:Damping enable, DPD:Damping del, (*, 234.254.254.255), RP: 46.63.1.1, TYPE: DYNAMIC, FLAGS: Incoming interface: NULL, flags:...

  • Page 67: Chapter 5 Pim-Ssm Configuration

    ZXR10(config-mcast-pim)# < access-list-name >] PIM-SSM group. Deletes the address range of a no ssm range ZXR10(config-mcast-pim)# PIM-SSM group. Descriptions of parameter in Step 2: Parameter Description < access-list-name > ACL name, with 1-31 characters SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 68: Pim-Ssm Configuration Example

    ZXR10 5900E Series Configuration Guide (Multicast) 5.3 PIM-SSM Configuration Example Configuration Description Figure 5-1 shows the network topology og a PIM-SSM configuration example. PIM-SM is enabled on S1, and SSM is configured. Configure the SSM group range (by default, it is 232.0.0.0/8). In this configuration example, IGMPv3 is used. The Tester 2 sends dynamic Join messages to the specific source.
  • Page 69 Flags:NS:SPT upsend, RT:Reg upsend, MT:tunnel, F:Forward, S:Syn mrt, NTP:NTP join, FLT:Flt add, FD:Flt del, DPU:Damping enable, DPD:Damping del, (15.1.1.1, 232.0.0.1), RP: 0.0.0.0, TYPE: DYNAMIC, FLAGS: NS Incoming interface: vlan1, flags: NS Outgoing interface list: vlan2, flags: F/S /*Generating (S,G) entity*/ SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 70 ZXR10 5900E Series Configuration Guide (Multicast) This page intentionally left blank. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 71 6.2 Configuring PIM-DM To configure the PIM-DM function on the ZXR10 5900E, perform the following steps: Step Command Function Enables PIM. router pim ZXR10(config-mcast)# no router pim Disables PIM. ZXR10(config-mcast)# SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 72: Maintaining Pim-Dm

    ZXR10 5900E Series Configuration Guide (Multicast) Step Command Function interface <interface-name> Enters PIM interface ZXR10(config-mcast-pim)# configuration mode. The parameter <interface-name> is the interface name. no interface <interface-name> Deletes the PIM interface ZXR10(config-mcast-pim)# configuration. Enables PIM on an interface. pimdm ZXR10(config-mcast-pim-if-interface-name)# Disables PIM on an interface.

  • Page 73: Chapter 6 Pim-Dm Configuration

    The ingress interface of the route entry is valid. The entry forwards multicast packets. Switches to the SPT when data flows are received. Number of interfaces that receive IGMP Join messages. Number of interfaces that do not receive IGMP Join messages. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 74: Pim-Dm Configuration Example

    ZXR10 5900E Series Configuration Guide (Multicast) Parameter Description Number of interfaces that have downstream nodes to receive data flows. LAst Number of interfaces that receives data flows but fails to asserts. Number of egress interfaces created based on entry types.
  • Page 75 The configuration commands of S2 are as follows: S2(config)#interface vlan7 S2(config-if-vlan7)#ip address 199.1.1.2 255.255.255.0 S2(config-if-vlan7)#no shutdown S2(config-if-vlan7)#exit S2(config)#interface vlan8 S2(config-if-vlan8)#ip address 35.1.1.1 255.255.255.0 S2(config-if-vlan8)#no shutdown S2(config-if-vlan8)#exit S2(config)#ip multicast-routing S2(config-mcast)#router pim S2(config-mcast-pim)#interface vlan7 S2(config-mcast-pim-if-vlan7)#pimdm S2(config-mcast-pim-if-vlan7)#exit S2(config-mcast-pim)#interface vlan8 S2(config-mcast-pim-if-vlan8)#pimdm S2(config-mcast-pim-if-vlan8)#end SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 76 ZXR10 5900E Series Configuration Guide (Multicast) Configuration Verification Run the show ip pim neighbor command on S1 to check the neighbor state. S1(config)#show ip pim neighbor Neighbor Address Interface DR Priority Uptime Expires 199.1.1.2 vlan3 00:09:14 00:01:36 Run the show ip pim interface command on S1 to check interface state.

  • Page 77: Chapter 7 Pim Snooping Configuration

    Enables PIM snooping globally. pim snooping ZXR10(config-pimsnoop)# vlan <vlan-id> Enters PIM snooping VPLS ZXR10(config-pimsnoop)# configuration mode. The <vpls-name> parameter is with 1-4094 characters. Sets PIM snooping function in pim snooping ZXR10(config-pimsnoop-vlan)# a VLAN. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 78: Maintaining Pim Snooping

    ZXR10 5900E Series Configuration Guide (Multicast) Step Command Function vpls <vpls-name> Enters PIM Snooping VPLS ZXR10(config-pimsnoop)# configuration mode. Enables the PIM snooping pim snooping ZXR10(config-pimsnoop-vpls-zte)# function in the VPLS instance. 7.3 Maintaining PIM Snooping To maintain the snooping function on the ZXR10 5900E, run the following commands.
  • Page 79 VLAN ID of a multicast group. Source-ip Source address. Group-ip Multicast group address. The following is sample output from the show ip pim snooping neighbor-info command: ZXR10#show ip pim snooping neighbor-info Index Port VLAN VPLS Neighbor-ip RemainTime SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 80 ZXR10 5900E Series Configuration Guide (Multicast) ------------------------------------------------------------ gei_0/1/1/1 168.2.0.11 For a description of the parameters in the execution result, refer to the following table: Parameter Description Index Serial number of an entry. Port Neighbor port. VLAN VLAN ID of a multicast group.

  • Page 81: Pim Snooping Configuration Example

    1. Configure a VLAN to make sure PE1 and PE2 in the same VLAN. 2. Enable global PIM Snooping. 3. Enable PIM Snooping in the VLAN. Configuration Commands The configuration of PE1: PE1(config)#switchvlan-configuration PE1(config-swvlan)#vlan 1 PE1(config-swvlan-sub)#switchport pvid gei-0/1/1/1 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 82 ZXR10 5900E Series Configuration Guide (Multicast) PE1(config)#pimsnoop PE1(config-pimsnoop)#pim snooping PE1(config-pimsnoop)#vlan 1 PE1(config-pimsnoop-vlan1#pim snooping The configuration of PE2: PE2(config)#switchvlan-configuration PE2(config-swvlan)#vlan 1 PE2(config-swvlan-sub)#switchport pvid gei-0/1/1/1 PE2(config)#pimsnoop PE2(config-pimsnoop)#pim snooping PE2(config-pimsnoop)#vlan 1 PE2(config-pimsnoop-vlan1#pim snooping Configuration Verification After the configurations, a VPLS PW is established successfully. CE1 and CE2 are multicast switches and they join a group.
  • Page 83 Chapter 7 PIM Snooping Configuration Index VLAN Source-IP Group-IP Ports Time ------------------------------------------------------------------------------- 2.2.2.3 229.0.0.3 gei-0/1/1/3 2979 ZXR10# SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 84 ZXR10 5900E Series Configuration Guide (Multicast) This page intentionally left blank. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 85: Chapter 8 Pimv6 Snooping Configuration

    Step Command Function Enters PIMv6 snooping global configuration pimv6snoop ZXR10(config)# mode. pimv6 Enables the PIMv6 snooping function ZXR10(config-pimv6snoop)# globally. snooping enable vlan <vlan-id> Enters PIMv6 snooping VLAN configuration ZXR10(config-pimv6snoop)# mode. <vlan-id>: range of 1–4094. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 86: Maintaining Pimv6 Snooping

    ZXR10 5900E Series Configuration Guide (Multicast) Step Command Function Enables the PIMv6 snooping function in the pimv6 ZXR10(config-pimv6snoop-vlan1)# VLAN. snooping enable Enters PIMv6 snooping VPLS configuration vpls ZXR10(config-pimv6snoop)# <vpls-name> mode. Enables the PIMv6 snooping function in the ZXR10(config-pimv6snoop-vpls-zte)# VPLS instance.
  • Page 87 The following is sample output from the show pimv6 snooping neighbor-info command: ZXR10#show pimv6 snooping neighbor-info Index Port VLAN VPLS Neighbor RemainTime --------------------------------------------------------------- gei-0/1/1/1 2001::2002 For a description of the parameters in the execution result, refer to the following table: SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 88 ZXR10 5900E Series Configuration Guide (Multicast) Parameter Description Index Serial number of an entry. Port Neighbor port. VLAN VLAN ID of a multicast entry. VPLS VPLS instance ID of a multicast entry. Neighbor Neighbor address. RemainTime Remaining aging time of a neighbor.

  • Page 89: Pimv6 Snooping Configuration Example

    3. Enable the PIMv6 snooping function in the VLAN. Configuration Commands Configuration of PE1: PE1(config)#switchvlan-configuration PE1(config-swvlan)#vlan 1 PE1(config-swvlan-sub)#switchport pvid gei-0/1/1/1 PE1(config)#pimv6snoop PE1(config-pimv6snoop)#pimv6 snooping enable PE1(config-pimv6snoop)#vlan 1 PE1(config-pimv6snoop-vlan1)#pimv6 snooping enable Configuration of PE2: PE2(config)#switchvlan-configuration PE2(config-swvlan)#vlan 1 PE2(config-swvlan-sub)#switchport pvid gei-0/1/1/1 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 90 ZXR10 5900E Series Configuration Guide (Multicast) PE2(config)#pimv6snoop PE2(config-pimv6snoop)#pimv6 snooping enable PE2(config-pimv6snoop)#vlan 1 PE2(config-pimv6snoop-vlan1)#pimv6 snooping enable Configuration Verification CE1 and CE2 are multicast switches, and they join a multicast group. Check multicast entries on PE1 and PE2. Check the information about the neighbor and entry on PE1 as follows:...

  • Page 91: Mld Snooping Overview

    VPLS VLAN configuration mode. ZXR10(config-mldsnoop)# vlan <vlan-id> Configures the query interval of a querier. query-interval ZXR10(config-mldsnoop)# <interval> <interval>: query interval, meaning the interval of sending query messages, range: 30–65535, unit: seconds, default: 125 seconds. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 92 ZXR10 5900E Series Configuration Guide (Multicast) Step Command Function Configures the maximum query-response query-response-i ZXR10(config-mldsnoop)# nterval <interval> interval of a querier. <interval>: maximum query-response interval, range: 1–255, unit: tick (1 tick = 100 milliseconds), default: 100 ticks (10 seconds). Enables the MLD snooping function in MLD ZXR10(config-mldsnoop-vpls-zte)# Snooping-VPLS configuration mode.
  • Page 93 VLAN in MLD Snooping-VLAN configuration mode. <interval>: interval of querying the last member, range: 1–25, unit: seconds, default: 1 second. Configures an ACL filtering rule in a VLAN in ZXR10(config-mldsnoop-vlan1)# <acl-name> MLD Snooping-VLAN configuration mode. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 94: Maintaining Mld Snooping

    ZXR10 5900E Series Configuration Guide (Multicast) Step Command Function Configures the operational node in MLD mode{pr ZXR10(config-mldsnoop-vlan1)# oxy | route | transparent} Snooping-VLAN configuration mode. Configures the maximum number of max-gr ZXR10(config-mldsnoop-vlan1)# oup-num <num> groups in a VLAN in MLD Snooping-VLAN configuration mode.
  • Page 95 VPLS mode. show mldsnoop vlan <vlan-id> Displays the information about configuration and users in MLD snooping VLAN mode. show mldsnoop vpls <vpls-name> Displays the information about configuration and users in MLD snooping VPLS mode. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 96 ZXR10 5900E Series Configuration Guide (Multicast) The following is sample output from the show mldsnoop command: ZXR10#show mldsnoop Group information: EN: Enabled; DIS: Disabled MHN: Max-Host-Number (S): Static; (D): Dynamic Instance infomation: IP-G:IP-GLOBAL ------------------------------------------------------------------ Index Type ID Name Group Source...
  • Page 97 For a description of the parameters in the execution result, refer to the following table: Parameter Description Index Serial number of an entry. VLAN VLAN ID of a user. Group Multicast group address of a user. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 98 ZXR10 5900E Series Configuration Guide (Multicast) Parameter Description Source Source address of a user. State User state. RemainTime Remaining aging time of a user. Ports Port of a user. The following is sample output from the show mldsnoop query command:...
  • Page 99 Summary Statistical information. The following is sample output from the show mldsnoop summary vlan command: ZXR10#show mldsnoop summary vlan 1 The summary information about group: Type Summary ----------------------------------------- Total Exist-host Cfg-drop Cfg-max-host Source-Specific Anycast-Specific SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 100 ZXR10 5900E Series Configuration Guide (Multicast) For a description of the parameters in the execution result, refer to the following table: Parameter Description Type Statistical type. Summary Statistical information. The following is sample output from the show mldsnoop vlan command:...

  • Page 101: Mld Snooping Configuration Example

    Create VLAN 10, and add gei-0/1/1/1 and gei-0/1/1/4 to the VLAN. Enable the MLD snooping function in the VLAN. c. Simulate the hosts to join multicast group ff03::1 on gei-0/1/1/2 and gei-0/1/1/4. Configuration Commands Configuration of switch A: SwitchA# SwitchA#configure terminal 9-11 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 102 ZXR10 5900E Series Configuration Guide (Multicast) Enter configuration commands, one per line. End with CTRL/Z. SwitchA(config)#switchvlan-configuration SwitchA(config-swvlan)#vlan 10 SwitchA(config-swvlan-sub)#switchport pvid gei-0/1/1/1 SwitchA(config-swvlan-sub)#exit SwitchA(config-swvlan)#vlan 10 SwitchA(config-swvlan-sub)#switchport pvid gei-0/1/1/2 SwitchA(config-swvlan-sub)#exit SwitchA(config-swvlan)#vlan 10 SwitchA(config-swvlan-sub)#switchport pvid gei-0/1/1/3 SwitchA(config-swvlan-sub)#exit SwitchA(config-swvlan)#vlan 10 SwitchA(config-swvlan-sub)#switchport pvid gei-0/1/1/4 SwitchA(config-swvlan-sub)#exit...

  • Page 103: Msdp Overview

    RPs with the same address in the same PIM-SM domain and establish MSDP peer relationship between these RPs. This is to realize load sharing and redundancy for the RPs in the domain. 10-1 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 104: Configuring Msdp

    ZXR10 5900E Series Configuration Guide (Multicast) 10.2 Configuring MSDP To configure the MSDP function on the ZXR10 5900E, run the following commands: Command Function Enables the MSDP function. router msdp ZXR10(config-mcast)# Disables the MSDP function. no router msdp ZXR10(config-mcast)# Configuring an MSDP Neighbor...
  • Page 105 0–255, with the default value 0. For a description of the parameter in Step 5, refer to the following table: Parameter Description <ttl-value> TTL value, in the range of 1–254. 10-3 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 106 ZXR10 5900E Series Configuration Guide (Multicast) Configuring an MSDP Policy To configure an MSDP policy on the ZXR10 5900E, perform the following steps: Step Command Function redistribute [list <access-list-name>] According to the rules, ZXR10(config-msdp)# only the (S, G) multicast route...

  • Page 107: Maintaining Msdp

    MSDP neighbor in the SA cache. For a description of the parameters, refer to the following table: Parameter Description <peer-address> IP address of an MSDP neighbor <group-address> Specific multicast group address <source-address> Specific multicast source address 10-5 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 108 ZXR10 5900E Series Configuration Guide (Multicast) The following is sample output from the show ip msdp peer command: ZXR10#show ip msdp peer 101.1.1.1 MSDP Peer 101.1.1.1 Description: zte router 1 Connection status: State: Up, Resets: 9, Connection source: gei-0/1/1/1 (76.1.1.33)
  • Page 109 SA State per Peer Counters, <Peer>: <# SA learned> 1.1.1.1: 2 1.2.2.2: 20 1.3.3.3: 10 Total entries: 32 For a description of the parameters in the execution result, refer to the following table: 10-7 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 110: Msdp Configuration Example

    ZXR10 5900E Series Configuration Guide (Multicast) Parameter Description 1.1.1.1: 2 The IP address means the MSDP neighbor with this address. The count of SA messages that are received from this MSDP neighbor in the SA cache is 2. Total entries: 32 The count of SA messages that are received from all MSDP neighbors in the SA cache is 32.
  • Page 111 S1(config-msdp)#connect-source vlan20 S1(config-msdp)#peer 10.10.20.2 S1(config-msdp-peer)#exit S1(config-mcast)#router pimsm S1(config-pimsm)#interface vlan10 S1(config-pimsm-if)#pimsm S1(config-pimsm-if)#exit S1(config-pimsm)#interface vlan20 S1(config-pimsm-if)#pimsm S1(config-pimsm-if)#bsr-border S1(config-pimsm-if)#exit S1(config-pimsm)#interface vlan30 S1(config-pimsm-if)#pimsm S1(config-pimsm-if)#exit The configuration of S2: S2(config)#interface loopback2 S2(config-if)#ip address 2.2.2.2 255.255.255.0 S2(config-if)#exit S2(config)#ip multicast-routing 10-9 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 112 ZXR10 5900E Series Configuration Guide (Multicast) S2(config-mcast)#router pimsm S2(config-pimsm)#rp-candidate loopback2 priority 20 S2(config-pimsm)#bsr-candidate loopback2 hash-mask-length 10 priority 20 S2(config-pimsm)#exit S2(config-mcast)#exit S2(config)#interface vlan20 S2(config-if)#ip address 10.10.20.2 255.255.255.0 S2(config-if)#exit S2(config)#interface vlan40 S2(config-if)#ip address 10.10.40.1 255.255.255.0 S2(config-if)#exit S2(config)#interfacevlan50 S2(config-if)#ip address 10.10.50.1 255.255.255.0 S2(config-if)#exit S2(config)#router ospf 1 S2(config-ospfv2)#network 10.10.20.0 0.0.0.255 area 0...
  • Page 113 Use the show ip msdp summary command on S1 to check the establishment of MSDP peer relationship. S1#show ip msdp summary MSDP Peer Status Summary Peer Address State Uptime/ Reset Downtime Count Count 10-11 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 114 ZXR10 5900E Series Configuration Guide (Multicast) 10.10.20.2 00:05:34 S2#show ip msdp summary MSDP Peer Status Summary Peer Address State Uptime/ Reset Downtime Count Count *10.10.20.1 00:07:34 10.10.40.2 00:08:45 S3#show ip msdp summary MSDP Peer Status Summary Peer Address State Uptime/...

  • Page 115: Chapter 11 Static Multicast Configuration

    The RPF mechanism uses the multicast source address as the destination and selects an optimal route from the unicast routing table, the MBGP routing table and the static multicast routing table respectively. If the longest matching rule is configured, the RPF mechanism 11-1 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 116: Configuring Static Multicast

    ZXR10 5900E Series Configuration Guide (Multicast) selects the route that meets the longest matching rule among the three routes. If the masks are the same, the RPF mechanism selects the route with the highest priority among the three routes. If the priorities are the same, the RPF mechanism selects the route in the order of static multicast route, MBGP route and unicast route.

  • Page 117: Static Multicast Maintenance

    Outgoing interface list: The following is sample output from the show ip multicast-static-route summary command: ZXR10#show ip multicast-static-route summary IP Static Multicast Routing Table Summary (*,G): 0 routes (S,G): 1 routes Total: 1 routes 11-3 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 118: Static Multicast Configuration Example

    ZXR10 5900E Series Configuration Guide (Multicast) 11.4 Static Multicast Configuration Example Configuration Description As shown in Figure 11-1, a static multicast route with the source 33.1.1.2 and destination 225.10.1.2 is configured to forward multicast flows properly. Figure 11-1 Static Multicast Configuration Example Configuration Flow 1.
  • Page 119 Chapter 11 Static Multicast Configuration Outgoing interface list: gei-0/1/1/2 S1(config)#show ip mroute IP Multicast Routing Table (33.1.1.2, 225.10.1.2), RP: 0.0.0.0, TYPE: STATIC, FLAGS: Incoming interface: gei-0/1/1/1, flags: Outgoing interface list: gei-0/1/1/2, flags: 11-5 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 120 ZXR10 5900E Series Configuration Guide (Multicast) This page intentionally left blank. 11-6 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 121: Figures

    Figure 7-1 PIM Snooping Configuration Example............7-5 Figure 8-1 PIMv6 Snooping Configuration Example ..........8-5 Figure 9-1 MLD Snooping in a VLAN ..............9-11 Figure 10-1 MSDP Configuration Example.............. 10-8 Figure 11-1 Static Multicast Configuration Example ..........11-4 SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 122 Figures This page intentionally left blank. SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...

  • Page 123: Glossary

    - Network Element - Protocol Independent Multicast PIM-DM - Protocol Independent Multicast - Dense Mode PIM-SM - Protocol Independent Multicast - Sparse Mode - Request For Comments - Rendezvous Point - Reverse Path Forwarding SJ-20150114102049-007|2015-01-15 (R1.0) ZTE Proprietary and Confidential...
  • Page 124 ZXR10 5900E Series Configuration Guide (Multicast) - Shortest Path Tree - Source Specific Multicast SVLAN - Selective Virtual Local Area Network - Transmission Control Protocol TCP/IP - Transmission Control Protocol/Internet Protocol - Termination of Service - Time To Live VLAN...

Table of Contents