Daikin Altherma ERLQ004-006-008CA Reference Manual page 104

8/8
Field settings table
Breadcrumb Field code Setting name
A.8 [C-08] Which type of external sensor is installed?
A.8 [C-09] What is the required alarm output contact type?
A.8 [C-0A] --
A.8 [C-0C] High electricity price decimal (Do not use)
A.8 [C-0D] Medium electricity price decimal (Do not use)
A.8 [C-0E] Low electricity price decimal (Do not use)
A.8 [D-00] Which heaters are permitted if prefer. kWh rate PS is cut?
A.8 [D-01] Contact type of preferential kWh rate PS installation?
A.8 [D-02] Which type of DHW pump is installed?
A.8 [D-03] Leaving water temperature compensation around 0°C.
A.8 [D-04] Is a demand PCB connected?
A.8 [D-05] Is the pump allowed to run if prefer. kWh rate PS is cut?
A.8 [D-07] --
A.8 [D-08] Is an external kWh meter used for power measurement?
A.8 [D-09] Is an external kWh meter used for power measurement?
A.8 [D-0A] --
A.8 [D-0B] --
A.8 [D-0C] What is the high electricity price (Do not use)
A.8 [D-0D] What is the medium electricity price (Do not use)
A.8 [D-0E] What is the low electricity price (Do not use)
A.8 [E-00] Which type of unit is installed?
A.8 [E-01] Which type of compressor is installed?
A.8 [E-02] What is the indoor unit software type?
A.8 [E-03] What is the number of backup heater steps?
A.8 [E-04] Is the power saving function available on the outdoor unit?
A.8 [E-05] Can the system prepare domestic hot water?
A.8 [E-06] Is a DHW tank installed in the system?
A.8 [E-07] What kind of DHW tank is installed?
A.8 [E-08] Power saving function for outdoor unit.
A.8 [E-09] --
A.8 [E-0A] --
A.8 [E-0B] Is a bi-zone kit installed?
A.8 [E-0C] --
A.8 [E-0D] --
A.8 [F-00] Pump operation allowed outside range.
A.8 [F-01] --
A.8 [F-02] Bottom plate heater ON temperature.
A.8 [F-03] Bottom plate heater hysteresis.
A.8 [F-04] Is a bottom plate heater connected?
A.8 [F-05] --
A.8 [F-06] --
A.8 [F-09] Pump operation during flow abnormality.
A.8 [F-0A] --
A.8 [F-0B] Close shut-off valve during thermo OFF?
A.8 [F-0C] --
A.8 [F-0D] What is the pump operation mode?
4P401673-1 - 2015.04
Range, step
Default value
R/W
0: No
1: Outdoor sensor
2: Room sensor
R/W 0: Normally open
1: Normally closed
0
R/W 0~7
0
R/W 0~7
0
R/W 0~7
0
R/W 0~3
0: None
2: BUH only
R/W
0: No
1: Active open
2: Active closed
R/W 0: No
1: Secondary rtrn
2: Disinf. shunt
R/W 0: Disabled
1: Enabled, shift 2°C (from -2 to 2°C)
2: Enabled, shift 4°C (from -2 to 2°C)
3: Enabled, shift 2°C (from -4 to 4°C)
4: Enabled, shift 4°C (from -4 to 4°C)
R/W
0: No
1: Pwr consmp ctrl
R/W 0: Forced off
1: As normal
R/O 0
R/W
0: No
1: 0,1 pulse/kWh
2: 1 pulse/kWh
3: 10 pulse/kWh
4: 100 pulse/kWh
5: 1000 pulse/kWh
R/W
0: No
1: 0,1 pulse/kWh
2: 1 pulse/kWh
3: 10 pulse/kWh
4: 100 pulse/kWh
5: 1000 pulse/kWh
0
2
R/W 0~49
0
R/W 0~49
0
R/W 0~49
0
R/O
0~5
0: LT split
R/O 0: 8 (*5)
1: 16 (*6)
R/O 0~1
1: Type 2
R/O 0~2
1: 1 step
R/O 0: No (*6)
1: Yes (*5)
R/W 0: No
1: Yes
R/O 0: No
1: Yes
R/O 0~6
1: Type 2
R/W 0: Disabled (*6)
1: Enabled (*5)
0
0
R/O 0~1
1: Yes
0
0
R/W 0: Disabled
1: Enabled
R/W 20
R/W 3~10°C, step: 1°C
3°C
R/W 2~5°C, step: 1°C
5°C
R/W 0: No
1: Yes
0
0
R/W 0: Disabled
1: Enabled
0
R/W
0: No
1: Yes
R/W 1
R/W 0: Continuous
1: Sample
2: Request
Installer setting at variance with
default value
Date Value
(*5) *04/08*
(*6) *16*