Emerson Unidrive M100 Control User Manual page 66

Safety Product Mechanical
information information installation
Parameter
06.001 Stop Mode
06.002 Limit Switch Stop Mode
06.003 Supply Loss Mode
06.004 Start/Stop Logic Select
06.006 Injection Braking Level
06.007 Injection Braking Time
06.008 Hold Zero Frequency
06.009 Catch A Spinning Motor
06.010 Enable Conditions
06.011 Sequencer State Machine Inputs
06.012 Enable Stop Key
06.014 Disable Auto Reset On Enable
06.015 Drive Enable
06.016 Date
06.017 Time
06.018 Day Of Week
06.019 Date/Time Selector
06.020 Date Format
06.021 Time Between Filter Changes
Filter Change Required /
06.022
Change Done
06.023 Time Before Filter Change Due
06.024 Reset Energy Meter
06.025 Energy Meter: MWh
06.026 Energy Meter: kWh
06.027 Energy Cost Per kWh
06.028 Running Cost
06.029 Hardware Enable
06.030 Run Forward
06.031 Jog Forward
06.032 Run Reverse
06.033 Forward/Reverse
06.034 Run
06.035 Forward Limit Switch
06.036 Reverse Limit Switch
06.037 Jog Reverse
06.038 User Enable
06.039 Not Stop
06.040 Enable Sequencer Latching
06.041 Drive Event Flags
06.045 Cooling Fan control
06.046 Supply Loss Hold Disable
Input Phase Loss Detection
06.047
Mode
06.048 Supply Loss Detection Level
06.051 Hold Supply Loss Active
Motor Pre-heat
06.052
Current Magnitude
Output Phase Loss Detection
06.058
Time
Output Phase Loss Detection
06.059
Enable
06.060 Standby Mode Enable
66
Electrical Getting Basic
installation started parameters
Range
( )
OL
CoASt (0), rP (1), rP.dc I (2),
dc I (3), td.dc I (4), diS (5)
StoP (0) or rP (1),
diS (0), rP.StoP (1),
ridE.th (2)
0 to 6
0.0 to 150.0 %
0.0 to 100.0 s
Off (0) or On (1)
diS (0), EnAbLE (1),
Fr.OnLy (2), rv.OnLy (3)
0 to 4087
0 to 127
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
00-00-00 to 31-12-99
00:00:00 to 23:59:59
Sun (0), Non (1), tuE (2), UEd (3),
thu (4), Fri (5), SAt (6)
SEt (0), Po.uP (1), run (2),
Acc.Po (3)
Std (0), US (1)
0 to 30000 Hours
Off (0) or On (1)
0 to 30000 Hours
Off (0) or On (1)
±999.9 MWh
±99.99 kWh
0.0 to 600.0
±32000
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
0 to 3
0 to 5
Off (0) or On (1)
FuLL (0), rIPPLE (1), diS (2)
0 to VM_SUPPLY_LOSS_LEVEL V
Off (0) or On (1)
0 to 100 %
0.5 (0) to 4 (3) s
Off (0) or On (1)
Off (0) or On (1)
Running the
Optimization NV Media Card
motor
Default
( )
OL
rP (1)
rP (1)
diS (0)
50 Hz: 0, 60 Hz: 4
100.0 %
1.0 s
Off (0)
diS (0)
Off (0)
Off (0)
On (1)
Po.uP (1)
Std (0)
0 Hours
Off (0)
0.0
Off (0)
Off (0)
Off (0)
Off (0)
Off (0)
Off (0)
Off (0)
Off (0)
Off (0)
Off (0)
Off (0)
0
2
Off (0)
FuLL (0)
110 V drive: 205 V
200 V drive: 205 V
400 V drive: 410 V
Off (0)
0 %
0.5 (0) s
Off (0)
Off (0)
Unidrive M100 / M101 Control User Guide
Advanced
Diagnostics UL Listing
parameters
Type
RW Txt
RW Txt
RW Txt
RW Num
RW Num RA
RW Num
RW Bit
RW Txt
RO Bin ND NC PT
RO Bin ND NC PT
RW Bit
RW Bit
RW Bit NC
RW Date ND NC PT
RW Time ND NC PT
RO Txt ND NC PT
RW Txt
RW Txt
RW Num
RW Bit ND NC
RO Num ND NC PT
RW Bit
RO Num ND NC PT
RO Num ND NC PT
RW Num
RO Num ND NC PT
RO Bit NC
RW Bit NC
RW Bit NC
RW Bit NC
RW Bit NC
RW Bit NC
RW Bit NC
RW Bit NC
RW Bit NC
RW Bit NC
RW Bit NC
RW Bit
RW Bin NC
RW Num
RW Bit
RW Txt
RW Num RA
RW Bit NC
RW Num
RW Txt
RW Bit
RW Bit
Issue Number: 1
US
US
US
US
US
US
US
US
US
US
US
US
US
US
PS
PS
PS
US
US
US
US
US
US
US
US
US
US