Rf Expander; Communications Device; Normal And Shift Key Functions - Honeywell VISTA-128BPT Programming Manual
Burglary partitioned security system
Hide thumbs
Also See for VISTA-128BPT:
- Installation and setup manual (124 pages) ,
- User manual (88 pages) ,
- Overview (13 pages)
Table of Contents
Advertisement
R
F
E
x
p
a
n
d
e
r
R
F
E
x
p
a
n
d
e
r
PROMPT
01 RF EXPANDER
HOUSE ID
00
C
o
m
m
u
n
i
c
a
t
i
o
n
s
D
e
C
o
m
m
u
n
i
c
a
t
i
o
n
s
D
e
If you selected device type 6, the 6160 Keypad functions similarly to the Programming Tool. See Figure 1 for the
functions of the keys on the 6160.
Figure 1: 6160 Key Functions for Programming Communications Device
Each key has two possible functions: a normal function and a SHIFT function. To perform a normal key function, simply
press the desired key. To perform a SHIFT key function, press SHIFT key, then press desired function key.
N
o
r
m
a
l
a
n
d
S
H
I
F
T
k
e
N
o
r
m
a
l
a
n
d
S
H
I
F
T
k
e
K
K
e
e
y
y
N
N
o
BS/ESC
[BS]: Press to delete entry
Also, can reset EEPROM defaults *
↓/↑
[↓]: Scroll down programming
N/Y
[N]: Press for "NO" answer
SHIF
Press before pressing a SHIFT key function. Will light READY LED. LED goes out once a key is pressed.
T
Press again for each SHIFT function desired.
1/A
[1]: For entering the number 1
2/B
[2]: For entering the number 2
3/C
[3]: For entering the number 3
4/D
[4]: For entering the number 4
5/E
[5]: For entering the number 5
6/F
[6]: For entering the number 6
7/S
[7]: For entering the number 7
8/T
[8]: For entering the number 8
9/X
[9]: For entering the number 9
∗/SPACE
[∗]: Not used
0
[0]: For entering the number 0
#/ENTER
[#/ENTER]: Press to accept entries
* Active only when the "REVIEW?" prompt is displayed.
The 6160 Keypad displays the following prompts, which are sent by the Communications Device transmitter to the control.
PROMPT
DEVICE ADDRESS
ID #
(1234)
If a different 4-digit customer account number is used in the communications device than is programmed into the
alarm control, the communications device will transmit communication device-specific messages (power-on reset,
AC fail, etc.) using the communications device customer number, and alarm messages using the control panel's
customer number. If these numbers are different, you will be billed for two AlarmNet communication device accounts.
NOTE: Refer to the Communications Device's instructions for the correct prompts.
EXPLANATION
If you selected device type 03 (RF receiver), this prompt appears. Enter the 2-digit House ID (00-31).
This is required if you are using a 5800 Bi-Direction Device.
Press [∗] to accept entry.
v
i
c
e
v
i
c
e
y
F
u
n
c
t
i
o
n
s
:
y
F
u
n
c
t
i
o
n
s
:
o
r
r
m
m
a
a
l
l
K
K
e
e
y
y
F
F
u
u
n
n
c
c
t
t
i
i
o
o
n
n
EXPLANATION
Enter the device address of the communications device. The default address is 3.
Press [∗] to accept entry.
Enter the 4-digit customer account number, 0001-9999. This ID number will appear in the messages
generated by the communications device. Messages generated by the panel and transmitted by the
communications device will contain the ID number programmed into the panel. The communications
device and the panel should have the same ID number, if possible.
SECTION 3: DATA FIELD DESCRIPTIONS
S
S
H
H
I
I
F
F
T
T
K
K
e
e
y
y
F
F
u
[ESC]: Press to quit Program Mode
[↑]: Scroll up programming
[Y]: Press SHIFT-Y for "YES" answer
[A]: Used for entering C.S. ID number
[B]: Used for entering C.S. ID number
[C]: Used for entering C.S. ID number
[D]: Used for entering C.S. ID number
[E]: Used for entering C.S. ID number
[F]: Used for entering C.S. ID number
[S]: Not used
[T]: Not used
[X]: No SHIFT function
[SPACE]: Not used
No SHIFT function
No SHIFT function
59
u
n
n
c
c
t
t
i
i
o
o
n
n
Hide quick links:
Advertisement
Table of Contents
