Bottom Hardware And Miscellaneous Parts, All Options Except 029 - Agilent Technologies N5242A Service Manual

Replaceable Parts
Replaceable Parts Listings

Bottom Hardware and Miscellaneous Parts, All Options Except 029

Reference Part
Designator Number
➀
0515-0372
➁
0515-0665
➂
0515-1410
➃
0515-0374
➄
N5242-20103
➅
N5242-00007
➆
0515-0430
➇
N5242-00006
➈
N5242-00011
➉
0515-1227
0460-2725
11
5022-1087
12
E4403-20033
13
0403-0285
0960-0055
14
0515-1521
15
N5242-00002
16
N5242-00018
17
N5242-00003
0515-1992
18
N5242-00009
19
N5242-00005
20
N5242-00019
21
1810-0118
22
08673-60040
23
2950-0001
24
2190-0016
25
6-72
Qty Description
Machine screw, M3.0 x 8, pan head (4 to attach A19 test set motherboard to
test set deck, 6 to attach A19 test set motherboard to stabilizer bracket, 4 to
attach stabilizer bracket to A20 IF mux board, 17 to attach test set deck to
chassis, 4 to attach A23–A24 mixer bricks to bottom of mixer brick
66 mounting block, 4 to attach A21 HMA26.5 to its mounting bracket, 8 to
attach A34–A37 source attenuators to their brackets, 8 to attach A42–A45
receiver attenuators to their brackets, 4 to attach A33 reference mixer switch
to its bracket, 3 to attach reference mixer switch bracket to test set deck, and
4 to attach test set front sub panel to test set deck front.)
Machine screw M3.0 x 14 (2 to attach splitter to top of mixer brick mounting
10
block and 8 to attach A38–A41 bias tees to their brackets.)
Machine screw M3.0 x 20 pan head (6 to attach mixer bricks to sides of
16
mixer brick mounting block, 8 to attach A25–A28 bridges to their mounting
brackets, and 2 to attach A50 combiner to its bracket.)
4
Machine screw M3.0 x 10 pan head (To attach mixer brick mounting block.)
1 Mounting block (For A23 and A24 mixer bricks.)
Bracket (For A34–A37 source attenuators, A39–A41 bias tees, and A42–A45
1
receiver attenuators.)
Machine screw M3.0 x 6 pan head (8 to attach bridge brackets to test set
30
deck, 12 to attach attenuator brackets to test set deck, 8 to attach switch
brackets to test set deck, and 2 to attach HMA26.5 bracket to test set deck.)
4
Bracket (For A25–A28 bridges.)
1
Bracket (For A33 reference mixer switch.)
4 Machine screw, M3.0 x 6, flat head (To attach test set front sub panel)
2
Vibration mount (4-port only; between couplers 1 and 3, and 2 and 4)
4 Test port coupler dress nut (One for each coupler.)
4
Gap pad; 4-port (Between each coupler and test set front sub panel.)
2
Coupler bumper; 2-port (Between each coupler and test set front sub panel.)
2
Termination, male SMA short circuit
4
Machine screw, M3.0 x 5, flat head (To attach front panel LED boards.)
1
Test set deck
1
Test set front sub panel, 2-port
1
Test set front sub panel, 4-port
8 Machine screw, M2.5 x 20, pan head (To attach A46–A49 bypass switches.)
1
Bracket (For A46–A49 bypass switches and A50 combiner.)
1
Bracket (For A21 HMA26.5.)
1
Stabilizer bracket (Between A19 test set motherboard and A20 IF mux board.)
2
Termination, 50-ohm load (For J6 and J7.)
2
Bulkhead connector (2-port models only.)
2
Hex nut (For bulkhead connector.) (2-port models only.)
2
Lock washer (For bulkhead connector.) (2-port models only.)
PNA Series Microwave Network Analyzers
Service Guide N5242-90001
N5242A