Agilent Technologies N5242A Service Manual page 333

Index
, , ,
illustrated 6-19 6-41
6-59
, ,
part numbers 6-18 6-24
, , ,
6-25 6-32 6-33 6-40
,
6-46 6-58
in external analyzer
,
illustrated 6-79
,
part numbers 6-78
in front panel assembly
, ,
illustrated 6-11 6-13
, ,
part numbers 6-10 6-12
in internal analyzer
,
illustrated 6-77
,
part numbers 6-76
in rear panel assembly
,
illustrated 6-81
,
part numbers 6-80
in top assembly, all options
, ,
illustrated 6-70 6-71
, ,
part numbers 6-14 6-15
locating
by reference designator
,
by type of part 6-7
miscellaneous
,
part numbers 6-82
,
required for servicing 2-12
replaceable
,
listing of 6-5
,
ordering information 6-3
parts, hardware
in bottom assembly
,
illustrated 6-73
,
part numbers 6-72
in external analyzer, all options
,
illustrated 6-79
,
part numbers 6-78
in internal analyzer, all options
,
illustrated 6-77
,
part numbers 6-76
in rear panel assembly, all
options
,
illustrated 6-81
,
part numbers 6-80
in top assembly, all options
, ,
illustrated 6-70 6-71
,
part numbers 6-70
parts, Option 029
in bottom assembly
,
illustrated 6-75
,
part numbers 6-74
parts, Option 029 hardware
in bottom assembly
,
illustrated 6-75
,
part numbers 6-74
password
,
Agilent administrator 7-50
performance
,
tests 3-28
Service Guide N5242-90001
,
6-47 calibration coefficients
description of
,
dynamic accuracy
,
frequency accuracy
,
noise floor 3-32
receiver compression
source maximum power
,
output
source power accuracy
source power linearity
test port output maximum
,
power 3-29
test port output power
accuracy
test port output power
linearity
,
trace noise
verification
ANSI/NCSL Z540-1-1994
,
6-70 non-ANSI/NCSL Z540-1-1994
3-9
,
6-5 performance test software,
,
internal 3-28
phase stability check
,
failure of 3-16
test port cables
pin assignments
connectors
HANDLER I/O
,
PULSE I/O
,
PWR I/O 5-15
TEST SET I/O
ping
command, LAN
from network
,
to analyzer 4-19
pixel
,
damaged 4-15
,
definition 4-15
Port 1
typical power output
Port 2
typical power output
Port 3
typical power output
Port 4
typical power output
post-repair procedures
power button keypad
removal and replacement
,
illustrated
,
procedure 7-11
power supply
,
check 4-7
functional description of
functional group
,
operation 5-34
power supply assembly
,
illustrated 6-15
,
3-33 part number
,
3-7 removal and replacement
,
3-34 illustrated
,
3-30 procedure
troubleshooting
,
3-31 power switch board
illustrated
parts list
3-29
,
removal and replacement
3-28
,
illustrated
3-29
procedure
power switch overlay
part number
power up
,
3-28
troubleshooting
power, source
,
3-29
accuracy test
3-30
linearity test
power, source output
,
3-8
maximum test
,
power, test port output
accuracy test
linearity test
maximum test
pre-repair
procedures
,
3-15
caution about
warnings about
preventive maintenance
,
5-14
effect on error terms
5-23
procedure
processing subgroup
,
5-13
operation
protection
,
4-19
against ESD
,
4-20
pulse generators-internal,
PULSE I/O
connector
pin assignments
,
4-34
pulse I/O adapter, accessory
pulse modulator-source 1,
,
4-34
pulse modulator-source 2,
,
4-34
pulsed RF measurements,
,
4-34
,
PWR I/O
7-64
connector
pin assignments
7-11
R channel
,
5-6 troubleshooting
,
5-4 R trace
troubleshooting
rack mount kits
part numbers
,
6-14
,
7-21
,
7-20
,
4-7
,
6-13
,
6-12
,
7-11
,
7-11
, ,
6-10 6-11
,
4-6
,
3-28
,
3-29
,
3-29
,
3-28
,
3-29
,
3-29
,
7-3
,
7-3
,
8-3
,
7-14
,
5-32
, , , ,
1-6 3-4 4-3 7-3
8-4
,
Option 025 2-4
,
5-23
,
2-9
,
Option 021 2-4
,
Option 022 2-4
,
Option H08 2-3
,
5-15
R
,
4-25
, ,
4-25 4-28
,
6-83
Index-13
,