Table of Contents
Advertisement
GENERAL INFORMATION
Pre-Operation
1.
Vacuum carpet and upholstery and remove other debris.
2.
Inspect power cord for damage.
Operation
1.
Squeeze the Adjustment Height lever.
2.
Pivot handle to desired position (best is at waist height).
3.
Release lever to lock handle in place.
4.
Place both hands firmly on the handle grips.
5.
Flip the power switch to the "on" position.
6.
To spray solution, squeeze either spray lever.
7.
To stop the machine, simply flip the power switch to the "off" position.
Pad Driver Removal / Installation
1.
Disconnect the power cord from the electrical outlet and empty any liquid in
the solution tank before installing a brush or pad driver.
2.
Leave the handle in the upright position and tip the machine backwards so it
rests on its wheels and upper handle section.
3.
Use an 11mm wrench to loosen and remove the four bolts from the bottom to
the pad driver.
4.
To install the pad driver, place the pad driver into position and bolt into place
with the original four 11mm bolts.
5.
Raise the machine back into upright position.
6.
To install a cleaning pad, tip the machine back and lower it, with the pad driver
installed, onto the cleaning pad. Keep the pad as centered as possible.
7.
When the machine is not in use, store it with the pad attached. This will protect
the pad driver from damage.
1.
Work away from outlet and power cord to prevent cord damage.
2.
To clean heavily soiled areas, repeat cleaning path from different direction.
Guidelines
1.
For ease of operation, always keep the brush or pad surface level, balanced,
and flat on the floor at all times.
2.
Always adjust the operating handle to a comfortable height at which the brush
or pad surface is balanced before starting the machine.
3.
Your floor machine will operate differently on various surfaces. There will be
more resistance when the machine is used with a brush on carpet than when it
is used with a pad on a smooth surface.
4.
To move the machine forward or backward, push or pull in the desired direc-
tion, keeping the pad or brush level on the floor at all times.
After Use
1.
Unplug the extension cord from wall and the machine's power cord pigtail and
loosely wind it up.
2.
After each use, wipe your floor machine with a clean, soft, damp cloth.
3.
Store in a clean, dry place with a pad attached to protect the pad driver.
4.
Do not expose to rain. Store indoors.
Maintenance Schedule
Maintenance item
Clean and inspect motor
Check power supply cable
Clean machine with all purpose cleaner and cloth
Inspect machine for water leaks and loose hardware
Troubleshooting
There is no power.
1.
Plug machine in proper outlet.
2.
Ensure that switch is not damaged or defective.
Plug on the power cord doesn't light up when plugged in.
1.
Replace the power cord.
Plug lights up when plugged in but machine does not turn on.
1.
Open the faceplate on the handle and check for loose or disconnected wires.
2.
Power switch may be bad. Replace the power switch.
Motor is drawing too many amps and blowing breakers.
1.
Power cord is defective or damaged - replace power cord.
2.
Check the power switch for shorts or loose connections. Replace the switch if
necessary.
3.
Check if the power cord from the switch is defective or damaged. Replace if
necessary.
ECO-15 Machine Specifications
Cleaning Path
Solution Tank
Consumption
Machine Weight
ECO-15 230V Configuration Information
Model Number
Consumption
ECO-17 Machine Specifications
Cleaning Path
Solution Tank
Consumption
Machine Weight
ECO-17 230V Configuration Information
Model Number
Daily
Once a week
Consumption
x
x
FAQs
x
Q: What comes standard with the Orbital Floor Machines?
x
A: The Orbital Floor Machines come with:
• Pad driver (pre-installed)
• 2x microfiber cleaning pads
• 50' extension cord (12/3)
Q: Where do I plug the machine in?
A: The Orbital Floor Machines require a grounded circuit. Please note: GFI outlets
may trip before the breaker setting.
Q: Is there anything I can do to increase the expected life of my machine?
A: Check all parts for wear regularly. Keep machine clean.
3
Motor
Pump
Pump PSI
Pump GPM
Levers
Deck Plate
Power
Machine
Dimensions
Power Cord
Power
Motor
Pump
Pump PSI
Pump GPM
Levers
Deck Plate
Power
Machine
Dimensions
Power Cord
Power
1 horsepower
15"
Diaphragm spray pump
100
1.3
4 gallons
Stainless steel
Stainless steel
13 amps @ 115V 60Hz
130 lbs.
27" x 15.5" x 49"
50' 12/3 extension cord
ECO15-230
6.5 amps @ 230V 60Hz
1 horsepower
17"
Diaphragm spray pump
100
1.3
4 gallons
Stainless steel
Stainless steel
13 amps @ 115V 60Hz
130 lbs.
27" x 17.5" x 49"
50' 12/3 extension cord
ECO17-230
6.5 amps @ 230V 60Hz
Advertisement
Table of Contents
