Advertisement
GeneRal InFoRMaTIon
dear Customer:
Congratulations on the purchase of your new Spinner
aware, the scene of the equipment world is becoming more high tech, and we
at Mytee Products Inc. strive to keep you on the cutting edge with superior quality
and technology.
Keep in mind that the Spinner
is a machine, so neglect or abuse will cause
®
unnecessary damage and void the warranty. However with simple maintenance
the Spinner
will give quality performance for many years to come.
®
If warranty questions arise, please consult your user manual or get in touch with
your distributor. If you have questions about maintenance, replacing parts or
ordering parts, please call an authorized Mytee Products Inc. Service Center.
To see an updated list, visit our website at www.mytee.com
Before you begin cleaning, please read your manual thoroughly.
Sincerely,
Mytee Customer Care Dept.
Parts and Service
Repairs, when required, should be performed by Mytee service personnel or Mytee
authorized Service Center using Mytee original replacement parts and accessories.
Call Mytee for repair parts or service. Please specify the Model and Serial Number
when discussing your machine.
name Plate
The Model and Serial Number of your machine are shown on the Nameplate on the
back panel of the machine. This information is needed when ordering repair parts
for the machine. Use the space provided on the front cover to note the Model and
Serial Number of your machine for future reference.
unpacking the Machine
When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it can
be inspected by the carrier that delivered it. Contact the carrier immediately to file a
freight damage claim.
Caution and Warnings
Symbols
Mytee uses the symbols below to signal potentially dangerous conditions. Always
read this information carefully and take the necessary steps to protect personnel
and property.
Is used to warn of immediate hazards that will cause severe personal injury or death.
Is used to call attention to a situation that could cause severe personal injury.
Is used to call attention to a situation that could cause minor personal injury or
damage to the machine or other property. When using an electrical appliance, basic
precautions should always be followed, including the following: Read all instructions
before using this machine. This product is intended for commercial use only.
To reduce the risk of fire, electrical shock, or injury:
1. Read all instructions before using equipment.
2. Use only as described in this manual. Use only manufacturer's recommended
attachments.
3. Always unplug or disconnect the appliance from power supply when not in use.
4. Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
5. Do not use in areas where flammable or combustible material may be present.
6. Do not leave the unit exposed to harsh weather elements. Temperatures below
freezing may damage components and void warranty.
7. Use only the appropriate handles to move and lift unit. Do not use any other parts
of this machine for this purpose.
8. Keep hair, loose clothing, fingers, and all parts of the body away from all
openings and moving parts.
9. Use extra care when cleaning on stairs.
10. When cleaning and servicing the machine, local or national regulations may apply
to the safe disposal of liquids which may contain: chemicals, grease, oil, acid, alka-
lines, or other dangerous liquids.
. As you are already
®
11. Do not leave operating unattended.
Use only non-flammable liquid in this machine.
Preparation
1. Remove furniture from cleaning area, and sweep or vacuum.
2. Protect cabinets, carpets, walls and painted surfaces from spray with drop cloths
or plastic.
3. Identification – Identify the type of floor you are going to clean. This step is vital,
since each flooring type may call for different chemicals, brushes and equipment.
Basic flooring types are: resilient (vinyl, VCT, linoleum), which is generally softer;
stone (terrazzo, quarry, ceramic, brick, concrete) made of natural materials; and
stone substitute (marble, slate and granite), which mimics stone.
4. Application – Once the flooring is identified, apply the appropriate type of cleaning
(or in the case of resilient flooring, stripping) chemical. On tile surfaces, spray chemi-
cal evenly over tile and grout lines, allowing it to pool in the lines.
5. Emulsification – Chemicals typically require dwell time to remove the dirt and
grime driven into the surface. The dirtier the floor, the longer the chemicals may need
to dwell. Without proper dwell time, chemicals will not be effective.
6. Agitation and Elimination – Agitate the chemical into the floor to facilitate cleaning
using a Spinner® floor machine connected to an extractor. The Spinner® lays down
high-pressure spray to agitate and rinse, and vacuums up the solution simultane-
ously, eliminating it from the surface.
Spinner
1. Attach the Vacuum and Solution Hoses to the extractor.
2. Attach the Solution Hose to the Male Quick Disconnect and the Vacuum Hose to
the Wand Tube.
3. Turn on the extractor to engage the vacuum, while making sure the bottom of the
Spinner™ is flush with the cleaning surface to ensure proper suction.
4. Squeeze the Spinner's™ high-pressure trigger gun to dispense solution on to
the surface.
5. Hold the machine at waist level and use a back-and-forth motion.
after use
1. Unplug.
2. Inspect hoses and replaced if damaged.
3. After each use, wipe floor machine with a clean, soft, damp cloth.
4. Do not expose to rain.
5. Store indoors. In a clean, dry place.
6. Do not store sitting on brush.
Maintenance Schedule
FaQs
Q – how much does my Spinner
A – Model 8901 – Weight: 23 pounds; Dimensions: 13"x13"x53"
Q—What can I do to extend the life of my Spinner
A – Follow the suggested maintenance schedule in this manual.
Trouble Shooting
The Spinner
1. Inspect the jets to make sure they are not clogged.
2. Check the machine for a normal flow of solution by disconnecting the Solution
Hose from the Spinner
3. If the solution's flow is disrupted, use Mytee
4. Try to spin the unit by hand. If it does not move, replace the swivel. If it moves, the
seal may need rebuilding. Take the Spinner
14
operation
®
Maintenance item
Clean and inspect hoses
Check for loose hardware
Clean machine with clean, soft damp cloth
Inspect spray jets once a week.
Use Mytee
System Maintainer 3601 every 100
®
hours. Circulate through the hose and tool.
weigh and dimensions?
®
Model 8902 – Weight 23 pounds; Dimensions: 13"x13"x53"
Model 8903 – Weight: 21 pounds; Dimensions: 13"x13"x53"
Model 8904 – Weight: 21 pounds; Dimensions: 23"x14"x51"
Model 8907 – Weight: 18 pounds; Dimensions: 13"x13"x53"
Model 8908 – Weight: 8 pounds; Dimensions: 14"x12"x12"
is not spinning.
®
and letting the liquid run freely.
®
Daily
Once a week
x
x
x
x
x
?
®
System Maintainer 3601.
®
to your local service center.
®
Advertisement
