Mytee ESCAPE ETM Instructions Manual
  1. Manuals
  2. Brands
  3. Mytee Manuals
  4. Floor Machine
  5. ESCAPE ETM
  6. Instructions manual

Mytee ESCAPE ETM Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instructions for
ESCAPE
Please read before use.
Register your product
at http://www.mytee.
com/support/register
General Information p. 2
Features p. 7
Switchplate p. 8
Power Options p. 9
Operation p. 10
Accessories p. 12
Parts & Pricing p. 14
Wiring Diagram p. 17
Vacuum System p. 19
Pump System p. 20
Auto Pump-Out System p. 21
ETM
™
13655 Stowe Dr., Poway, CA 92064
1
Model #
Serial #
Form # ADP-ETM
9-17

Advertisement

Table of Contents
loading

Related Manuals for Mytee ESCAPE ETM

Summary of Contents for Mytee ESCAPE ETM

  • Page 1 Instructions for ESCAPE ™ Please read before use. Register your product at http://www.mytee. com/support/register General Information p. 2 Features p. 7 Switchplate p. 8 Power Options p. 9 Operation p. 10 Accessories p. 12 Parts & Pricing p. 14 Wiring Diagram p. 17 Model # Vacuum System p.

  • Page 2: Dear Customer

    You can use the space provided on the front of this the quality and standard you’d expect out of the Mytee Products Inc. line. manual to note down both for future referencing.

  • Page 3: Installation

    Installation: 3. Using the hose attached to the primer, rest it inside the 2 ½” Vacuum Due to the variety of mounting conditions, Mytee Products Inc. does not Port and turn both vacuums on. supply the necessary hardware to mount the ETM to the operating vehicle.
  • Page 4 GENERAL INFORMATION ETM Float Switch Maintenance 5. Place the rubber washer over the threads of the new switch and all the way down to the 13/16” nut side. Each ETM machine contains three water level float switches. These float 6. Place a thin layer of silicone on the rubber washer. switches control certain functions of the machine.
  • Page 5 Generators for use with Escape® Electric Truck Mount the ten Philips head screws holding panel onto machine. Mytee Products recommends the use of a 10,000- ‐watt generator with 2. Locate sump pump float switch wires coming out of the black vacuum this unit.
  • Page 6 GENERAL INFORMATION watts, not peak watts. In any case, check with the Generator manufacturer to ensure the unit can provide 30 amps at 230 volts continuously.
  • Page 7 13. Recovery Tank 2. Prime Valve 9. Pump-Out THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE FINISH WITHOUT THE WRITTEN PERMISSION OF 3. Female Quick Disconnect 10.
  • Page 8 ESCAPE™ ETM ESCAPE™ ETM SWITCH PLATE AND POWER SOCKETS Top Socket: Powers Vac 1, Vac 2 Pump, & Pump-out. Bottom Socket: Powers Vac 3 and Vac 4. Top power socket Bottom power socket Plug in to top socket to use vacuum 1 or 2, pump or pump-out. To use vacuum 3 or 4 plug in bottom socket.
  • Page 9 ESCAPE™ ETM ESCAPE™ ETM POWER OPTIONS 1 & 2 Plug each 50’ power cord into the 3 or 4 prong electrical adaptor. Once connected, plug electrical adaptor into dryer outlet. ESCAPE™ ETM POWER OPTION 3 USING HUNTER BOXES (SOLD SEPARATELY) *sold separately Plug each 50’...
  • Page 10 ESCAPE™ ETM ESCAPE ETM PSI GAUGE & REGULATOR ESCAPE ETM PUMP PRIME / WASH OUT HOSE ™ ™ The gauge allows you to monitor PSI levels. Turning the Pressure The wash out hose is available for rinsing out recovery tank. Regulator to its left will decrease water pressure and turning to the right will increase water pressure.
  • Page 11 ESCAPE™ ETM ESCAPE™ ETM AUTO FILL & SOLUTION TANK DUMP VALVE For a convienent way to fill up the ETM’s solution tank, connect a water hose to the auto-fill. This will help speed up the work flow. Once the water level reaches a certain point the water stops, then refills again. Empty the solution tank by pulling the solution tank dump valve. ESCAPE™...
  • Page 12 REPRODUCTION IN PART OR AS A WHOLE SIZE DWG. NO. DRAWING IS THE SOLE PROPERTY OF TRex JR WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. ANY handle, back half, T-REX $0.99 ea <INSERT COMPANY NAME HERE> IS REPRODUCTION IN PART OR AS A WHOLE PROHIBITED.
  • Page 13 THE INFORMATION CONTAINED IN THIS SIZE DWG. NO. 8901 - Wand Style 8902 - “T” Style DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE FINISH WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED.
  • Page 14 ESCAPE™ ETM PARTS & PRICING Part prices are subject to change.
  • Page 15 ESCAPE™ ETM PARTS & PRICING...
  • Page 16 ESCAPE™ ETM PARTS & PRICING...
  • Page 17 ESCAPE™ ETM LOWER WIRING DIAGRAM...
  • Page 18 ESCAPE™ ETM UPPER WIRING DIAGRAM...
  • Page 19 ESCAPE™ ETM VACUUM SYSTEM...
  • Page 20 ESCAPE™ ETM HIGH PRESSURE PUMP SYSTEM...
  • Page 21 ESCAPE™ ETM AUTO PUMP-OUT SYSTEM...
  • Page 22 NOTES Mytee Products Inc. 13655 Stowe Dr. Poway, CA 92064 www.mytee.com F X 858.679.7814 © 2017 Mytee Products Inc. Printed in the U.S.A.

Table of Contents