Mytee 8070 -Lite Instructions Manual
Mytee-lite 8070 carpet extractor instructions
Hide thumbs
Also See for 8070 Mytee-Lite:
- Instruction manual (12 pages) ,
- Instructions manual (12 pages)
Table of Contents
Advertisement
Instructions for
Mytee- Lite
8070
Please read before use.
Please read before use.
Register your product
at http://www.mytee.com/
support/register
Set up p. 3
General information p. 6
Parts & pricing p. 9
Wiring diagram p. 11
Notes p.12
™
13655 Stowe Dr., Poway, Ca. 92064
1
Model #
Serial #
Form # ADM-8070
8-13
Advertisement
Table of Contents
Related Manuals for Mytee 8070 Mytee-Lite
Summary of Contents for Mytee 8070 Mytee-Lite
- Page 1 Instructions for Mytee- Lite 8070 ™ Please read before use. Please read before use. Register your product at http://www.mytee.com/ support/register Model # Set up p. 3 General information p. 6 Serial # Parts & pricing p. 9 Form # ADM-8070 Wiring diagram p.
-
Page 3: Product View
ENGLISH 8070 MYTEE-LITE™ FRONT BACK 1. Vacuum Lid 7. Handle with Storage Basket and Cord Wrap 2. Vacuum hose connector 8. Removable Vacuum Tank 3. Solution tank 9. Switch plate 4. Solution Hose Connector 10. 6” wheels 5. Motor base housing 11. - Page 4 8070 MYTEE-LITE™ FILL SOLUTION TANK ATTACH HOSE Firmly attach hose and quick disconnect. Make sure quick discon- Remove vacuum tank to fill solution tank (See release latch portion). For best results, fill with warm water (140 o F). nects snap together firmly. Once attached to unit connect Q.D. to upholstery tool.
- Page 5 To drain recovery tank, detach and empty from vacuum inlet. Add a defoamer in the recovery tank to reduce foam, prolonging Detach: Flip-up latch. Attach: Place latch. the life of the Mytee Lite™ vacuum motor . Twist counter clockwise Twist clockwise for release.
-
Page 6: Filling The Solution Tank
If damage is evident, save the shipping carton so that it can we at Mytee Products Inc. strive to keep you on the cutting edge with superior be inspected by the carrier that delivered it. Contact the carrier immediately to file a quality and technology. -
Page 7: Maintenance Schedule
4. Filters clogged, remove filters and rinse clean with water. 8. Wait 8–10 minutes for unit to pre-heat. 5. Heater is blocked; flush out with Mytee’s system maintainer. 9. Re-key upholstery tool until hot water begins flowing. 6. If brass check valve is stuck replace valve. - Page 8 EVENT SHALL MYTEE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, PROPERTY DAMAGES, OR PERSONAL INJURIES. All limited warranties are void for, and Mytee does not warrant in any way, any prod- uct that evidences misapplication, improper installation, abuse, lack of maintenance,...
-
Page 9: Parts & Pricing
8070 MYTEE-LITE™ PARTS & PRICING Part prices are subject to change. Order parts at: http://www.mytee.com/products/8070-mytee-lite-ii-automotive-detail-extractor... - Page 10 8070 MYTEE-LITE™ PARTS & PRICING...
-
Page 11: Wiring Diagram
8070 MYTEE-LITE™ WIRING DIAGRAM... -
Page 12: Notes
NOTES Mytee Products Inc. 13655 Stowe Dr. Poway, Ca. 92064 www.mytee.com © 2013 Mytee Products Inc. Printed in the U.S.A.
Need help?
Do you have a question about the 8070 Mytee-Lite and is the answer not in the manual?
Questions and answers
no hot water
The Mytee 8070 may not produce hot water if the heater switch is not turned on or if the machine has not been allowed to sit idle for 8–10 minutes after turning on the heater. Additionally, if there is a clog or vapor lock in the system, or if the pump is not functioning properly, hot water may not reach the spray tool.
This answer is automatically generated