Table of Contents
Advertisement
Quick Links
Instructions for
ECO-15 & ECO-17
Please read before use.
Register your product
at http://www.mytee.
com/support/register
General Information p. 2
Notes p. 16
Orbital Floor Machines
13655 Stowe Dr. Poway, CA 92064
1
Model #
Serial #
Form # ADM-ECO17
2-17
Advertisement
Table of Contents
Related Manuals for Mytee eco-15
Summary of Contents for Mytee eco-15
-
Page 1: Table Of Contents
Unboxing & Assembly p. 4 Set Up & Operation p. 5 Flywheel Bearing Replacement p. 9 Model # ECO-15 Parts & Pricing p. 11 Serial # ECO-17 Parts & Pricing p. 13 Orbital Machine Wiring Diagram p. 15 Form # ADM-ECO17 Notes p. -
Page 2: General Information
When the machine is delivered, carefully inspect the shipping cartons and the we at Mytee Products Inc. strive to keep you on the cutting edge with superior qual- machine for damage. If damage is evident, save the shipping cartons so that it can ity and technology. -
Page 3: After Use
To install the pad driver, place the pad driver into position and bolt into place with the original four 11mm bolts. ECO-15 230V Configuration Information Raise the machine back into upright position. To install a cleaning pad, tip the machine back and lower it, with the pad driver... -
Page 4: Unboxing & Assembly
ECO-15/ECO-17 UNPACKING & ASSEMBLY Tools Needed: The ECO-15 & ECO-17 ship in two boxes and will need to be assembled before use. Follow these • 5/16” allen hex key • Needle nose pliers directions to assemble the two pieces. 2. Remove both C-clips from the axle using needle nose 1. -
Page 5: Set Up & Operation
ECO-15/ECO-17 SETUP & OPERATION FRONT BACK 1. Power Switch 6. Pump 10. Handlebars 2. Handle Height 7. Motor 11. Faucet Fill Hose Adjustment Lever 8. Spray Jets 12. Solution Tank Drain Cap 3. Power Cord Pigtail 9. Solution Spray Levers 13. - Page 6 The pad driver is attached with The ECO-15 & ECO-17 feature a valve that allows you to four bolts (highlighted above). To use a pad, simply lay...
- Page 7 ECO-15/ECO-17 SETUP & OPERATION ECO-15 & ECO-17 CLEANING PATTERN To effectively clean floors, move the Orbital Floor Machine forwards and backwards, similar to using a household vacuum cleaner. Wet the floor by spraying solution as you roll the unit forwards.
- Page 8 ECO-15/ECO-17 SETUP & OPERATION USING THE ECO-15 & ECO-17 ON VARIOUS SURFACES IMPORTANT: Ensure that you are using the appropriate pad type depending on the surface you are cleaning. CARPET STONE TILE & GROUT WOOD EPOXY CONCRETE & MORE VINYL...
-
Page 9: Flywheel Bearing Replacement
ECO-15/ECO-17 FLYWHEEL BEARING REPLACEMENT Tools Needed: The flywheel bearing is a wear part, similar to rotors on • Medium-large flathead a car. Over time, the bearing will require replacing. screwdriver • 7/16” open-end wrench • 3/16” Allen wrench • 15/16” open-end wrench •... - Page 10 ECO-15/ECO-17 FLYWHEEL BEARING REPLACEMENT 7. Install the flywheel assembly by hand, threading it onto 8. By hand, turn the flywheel to assure the flywheel coun- the shaft clockwise until it stops at the jam nut. Use the terweight clears the motor bolt heads.
-
Page 11: Eco-15 Parts & Pricing
ECO-15 PARTS & PRICING... - Page 12 ECO-15 PARTS & PRICING...
-
Page 13: Eco-17 Parts & Pricing
ECO-17 PARTS & PRICING... - Page 14 ECO-17 PARTS & PRICING...
-
Page 15: Orbital Machine Wiring Diagram
ECO-15/ECO-17 WIRING DIAGRAM... -
Page 16: Notes
NOTES Mytee Products Inc. 13655 Stowe Dr. Poway, CA 92064 www.mytee.com © 2017 Mytee Products Inc. Printed in the U.S.A.