Page 1
User Manual MYTEE LITE Model: 8070 REV. 2/15/18 Carpet & Upholstery Spotter 13655 Stowe Dr. Poway, CA 92064 • P: (858) 679-1191 • F: (858) 726-6005 New & Reconditioned Equipment & Parts - www.southeasternequipment.net...
Page 2
Mytee Products and its employees are equally dedicated to developing with the industry and its advances. Like any other piece of machinery or technology, the Mytee Lite™ also requires the proper maintenance and care to keep the product working over extended use.
TABLE OF CONTENTS IMPORTANT SAFETY INFORMATION AT A GLANCE 1.1 - Technical Specifications 1.2 - Included with the Mytee Lite™ 1.3 - Mytee Lite™ Front View 1.4 - Mytee Lite™ Rear View 1.5 - Switch Plate 1.6 - Exploded View & Parts List MACHINE OPERATION 2.1 - Powering the Mytee Lite™...
When and if calling Mytee for support, please grounding plug. The plug must be plugged into an appro- have your Model and Serial Number available for faster priate outlet that is properly installed in accordance with assistance.
Page 5
IMPORTANT SAFETY INFORMATION product is intended for commercial use only. tional regulations may apply to the safe disposal of liquids which may contain: chemicals, grease, oil, acid, alkalines, To reduce the risk of fire, electrical shock, or injury: or other dangerous liquids. 1.
With handle: 33” x 12” x 36.5” Machine Dimensions Without handle: 18” x 12” x 28.5” Power Cord Single 25’ 12/3 1.2 - Included with the Mytee Lite™ 8501 15’ x 1.25” Vacuum & Solution 8400 4” Stainless Steel Upholstery Heatguard™ Hose Wrap Hose...
PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS SIZE DWG. NO. DRAWING IS THE SOLE PROPERTY OF 8070 MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED. SCALE: 1:24...
Page 11
#10-32 zinc $0.99 ea P590 cuties, 1/4" qd, strandard pack of 2 $2.99 ea P585 base, MyteeLite $89.99 ea ADM-8070 manaul, Mytee-Lite H212 flat washer, 9/16"ID x 1 1/16"OD, AN960-C916 $0.99 ea H427 washer, wave, axle $1.49 ea H279 wheel, 6"...
♦ 2.3 - Filling the Solution Tank 2.2 - Connecting Hoses & Cleaning Tools The Mytee Lite™ solution tank can be filled up via the fau- cet fill hose or from a bucket via the opening. ♦ New & Reconditioned Equipment & Parts - www.southeasternequipment.net...
2.4 - Operating the Mytee Lite™ 2.5 - Emptying the Solution & Recovery Tanks Switching On The Unit In order to avoid vapor locking the unit, the Mytee Lite’s™ components should be switched on by following the pro- cedure below: 1.
Inspect machine for water leaks and loose hardware. 3.1 - Filter Maintenance The Mytee Lite™ has a small filter on the top of the vac- uum stack in the recovery tank. This filter should be checked and cleaned after each use.
5 - TROUBLESHOOTING 5.1 - Vacuum Troubleshooting Drain valve/cap is loose Tighten the drain valve/cap. and is causing air leakage. Hose cuffs are loose and Tighten all hose cuffs reg- Vacuum is not turning on. causing air leakage. ularly as may loosen over Possible Cause Solution time.
Page 17
5 - TROUBLESHOOTING 5.2 - Pump Troubleshooting Pump runs but there is no spray. Possible Causes Solutions On a new unit, the check Remove the check valve Pump doesn’t turn on. valve between the pump temporarily and check to Possible Causes Solutions and heater may hang up, see if the pump will flow...
Page 18
Heater is not heating water. and check for leaks. Repair the leak. If there are no Possible Causes Solutions leaks, run Mytee’s System Loose electrical connec- Check all electrical con- Maintainer™ (Part # 3601) tion. nections, including power through the machine to cord and harness.
Page 19
The pumps are usually rated for 140°F water. Heater has hard water Run Mytee System Main- tainer™ (Part # 3601) buildup inside, leading to lost efficiency. through the machine regu-...