Receiver Dehydrator To Tee Tube Installation; Left Condenser To Tee Tube Removal; Left Condenser To Tee Tube Installation; Right Condenser To Tee Tube Removal - MD Helicopters MD Explorer Servicing And Maintenance

(2). Evacuate AC system (ref. Section
12-00-00).
(3). Disconnect receiver dehydrator to tee
tube (34) from receiver dehydrator (26)
and tee (47). Remove tube.
J. Receiver Dehydrator to Tee Tube
Installation
(Ref. Figure 409)
The receiver dehydrator must
CAUTION
be replaced each time the com­
pressor is removed, or the AC system is
opened. An early failure of the compressor
can occur.
(1). Remove and replace receiver dehydra­
tor (26) (ref. Procedure 22.).
(2). Connect tube to receiver dehydrator
(26) and tee.
(3). Torque captive nuts of tube 230 to 260
in-lb (25.99 to 29.38 Nm).
(4). Service AC system (ref. Section
12-00-00).
(5). Install Access Panel L210 (ref. Section
53-30-00).
K. Left Condenser to Tee Tube Removal
(Ref. Figure 409)
(1). Remove Access Panel L210 (ref. Section
53-30-00).
(2). Evacuate AC system (ref. Section
12-00-00).
(3). Remove tube (35) from tee (47) and LH
condenser (69).
L. Left Condenser to Tee Tube Installation
(Ref. Figure 409)
(1). Connect left condenser to tee tube to
tee and LH condenser (69).
(2). Torque tube nuts 230 to 260 in-lb
(25.99 to 29.38 Nm).
MD Helicopters, Inc.
Rotorcraft Maintenance Manual
CAUTION
pressor is removed, or the AC system is
opened. An early failure of the compressor
can occur.
(3). Remove and replace receiver dehydra­
(4). Service AC system (ref. Section
(5). Install Access Panel L210 (ref. Section
M. Right Condenser to Tee Tube Removal
(Ref. Figure 409)
(1). Remove access panels L210 and R210
(2). Evacuate AC system (ref. Section
(3). Disconnect right condenser to tee tube
(4). Remove screws (3), washers (2), clamps
N. Right Condenser to Tee Tube Installation
(Ref. Figure 409)
(1). Connect right condenser to tee tube to
(2). Install clamps, screws, and washers.
(3). Torque the captive nuts of tube 230 to
CAUTION
pressor is removed, or the AC system is
opened. An early failure of the compressor
can occur.
(4). Remove and replace receiver dehydra­
(5). Service AC system (ref. Section
(6). Install access panels L210 and R210
O. Left Condenser to High−Pressure Switch
(Ref. Figure 409)
(1). Remove access panels L210 and R210
21-50-00
The receiver dehydrator must
be replaced each time the com­
tor (26) (ref. Procedure 22.).
12-00-00).
53-30-00).
(ref. Section 53-30-00).
12-00-00).
(48) from tee (47) and RH condenser.
(1), and tube.
tee and RH condenser.
Torque screws.
260 in-lb (25.99 to 29.38 Nm).
The receiver dehydrator must
be replaced each time the com­
tor (26) (ref. Procedure 22.).
12-00-00).
(ref. Section 53-30-00).
Tube Removal
(ref. Section 53-30-00).
CSP−900RMM−2
Page 439
Revision 34