No Ice Conditions - Electrolux 5995502399 Service Manual

Test 59C: "Fill" Limit Switch Test
(See Flow Chart Test #59C)
Interactive test with audio
Upon entering the test, the ice mold position is checked.
If is not already in "Freeze" position, the mold is driven to
"Freeze". The Freezer display will show the current
status of the "Fill" limit switch, which should be "OFF".
Remove the ice maker cover for better switch access.
Activate the switch manually to observe the "on" status
displayed on the Freezer display and hear the audio
alarm (See test 58C). Release the switch and display will
change to 'OFF" with no sound.
Test 60C: "Freeze" Limit Switch Test
(See Flow Chart Test #60C)
Interactive test with audio.
Upon entering the test, ice mold position is checked. If
is not already in the "Fill" position the mold is driven to
the "Fill" position. The Freezer display will show the
current status of the "Freeze" limit switch, which should
be "OFF". Remove the ice maker cover for better switch
access. Activate the switch manually to observe the "on"
status displayed on Freezer display and hear the audio
alarm (See test 58C). Release the switch and display will
change to 'OFF" again with no sound.
Test 61C: Ice Maker Evaporator Heater Test
(See Flow Chart Test #61C)
Interactive.
Pull the cartridge heater out of the ice maker assembly
before staring this test. The electric wires are to be
connected and the ambient air temperature less then
48°F in order for bi-metal in-line switch to remain closed.
Touch the ON/OFF key to activate the heater. Verify
manually if the heater is working. Touching the ON/OFF
key again will turn the heater Off. The Freezer display
shows the heater current state "on" or "OFF".
Test 62C: EEV Test
(See Flow Chart Test #62C)
Automated.
Touch the ON/OFF key to start the test. When waiting for
the automated test result, the Fresh Food display will be
flashing the test ID and the Freezer display will be
showing the TH3 current temperature. (The ice maker
controller will fully open the EEV and wait 120 seconds
for the TH3 temperature to drop off a minimum 2°F).
After the delay, the test result is displayed on the Freezer
display as "P" for "Pass" or "F" for "Fail".
Ice Maker (Fresh Food Compartment)
Test 63C: Harvest Motor System Test
(See Flow Chart Test #63C)
Interactive
This test has the requirement that the ice bucket be
removed from the ice maker chamber prior to entering
this test. Also, if the ice mold is in the "Fill" position there
can be no ice on the evaporator fingers. Push the ON/
OFF key to start the test. The ice mold should move to
the "Freeze" position and the Freezer display shows the
current motor status codes, "0" = no errors detected.
From that moment, the ice mold will alternate its
positions continuously between "Freeze" and "Fill". After
completing the first full cycle (freeze – fill- freeze) the
Freezer display will show a "1" and icon "good". Pushing
the ON/OFF key again will stop the harvest motor. The
ice maker controller will monitor functionality of the "Fill"
and the "Freeze" limit switches as well as the travel time
between "Freeze" and "Fill". If any of the harvest motor
errors are detected, the motor stops. The Freezer
display will show the error code ("2" –harvest motor time
out or "3" -both switches On). After error condition
detection, pushing the ON/OFF key will reset the Freezer
display and restart the test.
Test 64C: Software Revision (XX) ID
The current ice maker controller firmware revision ID (two
digits: from 01 to 99) is saved by ice maker and
displayed on Freezer display when the test is entered.

No Ice Conditions

To diagnosis a no ice condition, follow the steps in
section 6 "Ice Bin Housing Removal". This will allow
access to the determine the condition of the ice mold,
and so the following flow charts can be used to assist in
diagnosis.
Flow Chart No Ice #1- Mold in Freeze position (Left) and
frozen solid.
Flow Chart No Ice #2 - Mold in Freeze position (left) not
frozen solid with water in mold.
Flow Chart No Ice #3 - Mold in Freeze position (left) no
water or ice in mold.
Flow Chart No Ice #4 - Mold in fill position with ice cubes
in mold.
Flow Chart No Ice #5 - Mold in Fill position with no
water.
Flow Chart No Ice #6 - Mold in intermediate position.
4-7