Table of Contents
Advertisement
2.7.6 Access Code Time Zone Programming (Up to 4 zones)
Factory setting in step 3 is 0 (Time Zones are OFF).
This programming sequence sets up time zones (up to 4) that can be applied to the "Access Codes" programmed in
section 2.6.4 into the Access Plus system. These time zones can be turned ON or OFF once they have been programmed.
1. Press
*
2. Enter a time zone number (3, 4, 5 or 6), then press
Do not use 0, 1 or 2 for time zone numbers. These are already used; 0 = always deny,
1 = 24/7 access for Relay 1, and Relays 3-8; 2 = 24/7 access for Relay 2, and Relays 3-8.
3. Press 0
You can terminate here (Go to step 11 to finish) if you have previously programmed the time zone and
only ON / OFF is desired.
4. Enter the beginning hour (01 to 12) and minutes (01 to 59), then press
5. Press 0
6. Enter the ending hour (01 to 12) and minutes (01 to 59), then press
7. Press 0
8. Enter the days of the week that the time zone is to be active, then press
Sun =1, Mon = 2, Tue = 3, Wed = 4, Thu = 5, Fri = 6, Sat = 7.
You can enter up to 7 numbers here (1-7) but all 7 spaces do not have to be populated with numbers.
For example, for the time zone to be active only on Saturdays and Sundays, enter 1 7
the numbers is not important; 17 is the same as 71.
9. Enter the relay number(s) that the time zone will apply to, then press
You can enter a single relay number; all relay numbers (up to 8), or any combination of relay numbers.
10. Repeat steps 2 through 9 to program the other time zones (up to 4) if desired.
11. Press 0 # TOGETHER to end. [0 # (beeeeeep)]
If you make a mistake while programming steps, press "0 #" together and start at step 1 again.
2.8 Miscellaneous
2.8.1 Restore Factory Settings
This step will restore the factory settings for each of the programming parameters. See the "Quick Reference Table" on
page 36 for all of the factory settings. The master code (2.1) will remain intact after the factory settings have been restored.
WARNING: Once started, this sequence will program all values to factory settings.
2.8.2 Erase Transaction Log
This step will erase (empty) the transactions stored in the system history buffer (the system stores up to 500 transactions).
WARNING: Transaction log cannot be recovered after this sequence is started.
1810-162-A-6-16
3 6 and enter the MASTER CODE. [
to turn the time zone OFF, OR press 1
*
for AM OR press 1
for PM. [ _
*
*
for AM OR press 1
for PM. [ _
*
*
1. Press
9 0 and enter the MASTER CODE. [
*
2. Press 9 9 9 9, then press
3. The programming sequence will end itself automatically. [beeeeeep]
1. Press
9 1 and enter the MASTER CODE. [
*
2. Press 9 9 9 9, then press
3. The programming sequence will end itself automatically. [beeeeeep]
3 6 _ _ _ _ (beep)]
*
. [ _
(beep)]
*
*
to turn the time zone ON. [ _
*
(beep)]
*
(beep)]
*
9 0 _ _ _ _ (beep)]
*
. [ 9 9 9 9 (beep)]
*
9 1 _ _ _ _ (beep)]
*
. [ 9 9 9 9 (beep)]
*
(beep)]
*
. [ _ _ _ _
(beep)]
*
*
. [ _ _ _ _
(beep)]
*
*
. [ _ _ _ _ _ _ _
(beep)]
*
*
. The order of
*
. [ _
(beep)]
*
*
45
Advertisement
Chapters
Table of Contents
Troubleshooting
