Table of Contents
Advertisement
2.7 Time Functions
2.7.1 Time and Date Calendar Chip Programming
This programming sequence programs the calendar chip in the Access Plus system for the current time and date. The
calendar chip must be programmed if any of the time related features are going to be used.
Note: The clock / calendar chip in the Access Plus system will keep time for approximately 48 hours if power to the system
is lost or removed. If power is off longer than this, the clock / calendar chip will have to be reprogrammed.
1. Press
2. Enter the current hour (01 to 12) and minutes (01 to 59), then press
3. Press 0
4. Enter the month (01 to 12), day of the month (01 to 31) and the year (00 to 99), then press
5. Enter the day of the week (1-7), then press
6. Press 0 # TOGETHER to end. [0 # (beeeeeep)]
Example: Saturday, February 14th, 2010, 11:30 AM.
If you make a mistake while programming steps, press "0 #" together and start at step 1 again.
2.7.5 Automatic Relay Activation Time Zone Programming (Up to 4)
Factory setting in step 3 is 0 (Time zones are OFF).
This program sequence sets up time zones to automatically activate and deactivate relays 1 through 8. Up to Four time
zones can be programmed, each of which can be assigned to the desired relay(s). These time zones can be independently
turned ON or OFF after they have been programmed.
1. Press
*
2. Enter a time zone number (1, 2, 3 or 4), then press
3. Press 0
*
here (Go to step 11 to finish) if you have previously programmed the time zones and only ON / OFF is desired.
4. Enter the beginning hour (01 to 12) and minutes (01 to 59), then press
5. Press 0
*
6. Enter the ending hour (01 to 12) and minutes (01 to 59), then press
7. Press 0
*
8. Enter the days of the week that the auto relay time zone is to be active, then press
Sun =1, Mon = 2, Tue = 3, Wed = 4, Thu = 5, Fri = 6, Sat = 7.
You can enter up to 7 numbers here (1-7) but all 7 spaces do not have to be populated with numbers. For
example, for the auto relay time zone to be active only on Saturdays and Sundays, enter 1 7
numbers is not important; 17 is the same as 71.
9. Enter the relay number(s) that the time zone will apply to, then press
You can enter a single relay number; all relay numbers (up to 8), or any combination of relay numbers.
10. Repeat steps 2 through 9 to program the other auto relay time zones (up to 4) if desired.
11. Press 0 # TOGETHER to end. [0 # (beeeeeep)]
44
3 3 and enter the MASTER CODE. [
*
for AM OR press 1
*
[ _ _ _ _ _ _
(beep)]
*
Sun =1, Mon = 2, Tue = 3, Wed = 4, Thu = 5, Fri = 6, Sat = 7.
3 5 and enter the MASTER CODE. [
to turn the time zone OFF, OR press 1
for AM OR press 1
for PM. [ _
*
for AM OR press 1
for PM. [ _
*
3 3 _ _ _ _ (beep)]
*
for PM. [ _
(beep)]
*
*
. [ _
(beep)]
*
*
Your Master Code -
1.
Time -
2. 1 1 3 0
AM -
3. 0
Date -
4. 0 2 1 4 1 0
Day -
5. 7
End Programming -
6. 0 # TOGETHER (beeeeeep)
3 5 _ _ _ _ (beep)]
*
. [ _
(beep)]
*
*
to turn the time zone ON. [ _
*
(beep)]
*
(beep)]
*
. [ _ _ _ _
(beep)]
*
*
3 3 _ _ _ _ (beep)
*
(beep)
*
(beep)
*
(beep)
*
(beep)
*
(beep)] You can terminate
*
. [ _ _ _ _
(beep)]
*
*
. [ _ _ _ _
(beep)]
*
*
. [ _ _ _ _ _ _ _
*
*
. [ _
(beep)]
*
*
.
*
(beep)]
*
. The order of the
1810-162-A-6-16
Advertisement
Chapters
Table of Contents
Troubleshooting
