Table of Contents
Advertisement
2.4.13 Set Call Forward Microphone Gain and Speaker Volume
Factory setting is 71 (7 - Microphone, 1 - Speaker).
This adjustment is required only if the Access Plus unit is being used in the auto-dialer mode (directory codes 24-50). This
step will adjust the microphone gain (the remote handset loudness) and the speaker volume (the Access Plus unit
loudness) during call forwarding operation. You may have to perform these steps several times to get the optimal micro-
phone gain and speaker volume adjustment.
Before making any adjustments, do a test call as the programmed defaults may work fine for you and no additional
adjustments may be necessary. If adjustments are made, you will need to do a call forward test call after each adjustment
to determine if the result is to your liking.
The valid values for both the microphone gain and speaker volume are 0 through 9. These values are entered as a two-digit
number in step 2 below. The first digit is the microphone gain; the second digit is the speaker volume. The default setting is
71, which means that the microphone gain is set to 7 and the speaker volume is set to 1. A higher value increases the
loudness where as a lower value decreases the loudness.
1. Press
2. Enter a two-digit microphone gain and speaker volume setting, then press
3. Press 0 # TOGETHER to end. [0 # (beeeeeep)]
2.4.14 Hang-Up Tone Number
Factory setting is 0
This sets the number that when pressed on the phone will hang-up the Access Plus unit after conversation is complete.
1. Press
2. Choose and enter a single-digit hang-up number, then press
3. Press 0 # TOGETHER to end. [0 # (beeeeeep)]
2.5 Directory Codes
2.5.0 Directory Codes 1 – 23 PRE-SET (1816 Telephone Interface ONLY)
This programming step is only used if the Access Plus unit is connected to an 1816 Access Plus telephone interface.
This programming step is not applicable when the Access Plus unit is used as an auto-dialer.
Directory codes 01-23 are PRE-SET to dial relay numbers and telephone interface lines associated with the 1816 system.
Pre-Set numbers can be turned off but MUST to be ON to function.
1. Press
2. Enter a two-digit directory code (01-23), then press
3. Press 0
4. Repeat steps 2 and 3 to turn other directory codes ON or OFF.
5. Press 0 # TOGETHER to end. [0 # (beeeeeep)]
2.5.1 Directory Codes 24 – 50 "Dial Phone Number"
The Access Plus unit has the capability of operating as an auto-dialer system and can store up to 27 phone numbers in its
memory. When a visitor enters a directory code on the system keypad, the Access Plus unit will call the phone number
programmed under the specific directory code number. The directory codes, 24 through 50 cannot be revised after they
have been programmed into the system memory, only deleted (see 2.5.2 on next page).
1. Press
2. Enter a two-digit directory code (24-50), then press
3. Enter the phone number (up to 20 digits, no dashes), then press
4. Repeat steps 2 and 3 to enter additional numbers.
5. Press 0 # TOGETHER to end. [0 # (beeeeeep)]
40
1 1 and enter the MASTER CODE. [
*
The first digit is the microphone gain (0-9); the second digit is the speaker volume (0-9).
1 7 and enter the MASTER CODE. [
*
4 0 and enter the MASTER CODE. [
*
to turn the directory code OFF OR press 1
*
4 1 and enter the MASTER CODE. [
*
All 20 spaces do not have to be populated with numbers.
1 1 _ _ _ _ (beep)]
*
1 7 _ _ _ _ (beep)]
*
. [ _ _
*
*
4 0 _ _ _ _ (beep)]
*
. [ _ _
(beep)]
*
*
to turn the directory code ON. [ _
*
4 1 _ _ _ _ (beep)]
*
. [ _ _
(beep)]
*
*
. [ _ _ _ _ _ _ _ _ _ _ _
*
. [ _ _
(beep)]
*
*
(beep)]
(beep)]
*
(beep)]
*
1810-162-A-6-16
Advertisement
Chapters
Table of Contents
Troubleshooting
