Malfunctions; Moving And Storage - Tunturi T70 Owner's Manual

ALIGNING THE RUNNING bELT
Monitor belt tracking during exercise and make
adjustments as needed. The belt should run in the
center of the treadmill. Alignment is not usually needed,
provided
• the treadmill is placed on an even, solid and
horizontal surface and the belt is correctly tensioned
• the alignment of the belt is correct It is, however,
possible for the belt to be pushed to one side due to the
user's running style (e.g. more weight on one foot). The
alignment of the belt is adjusted by turning the two bolts
at the back of the treadmill.
aLiGn tHE BELt aCCorDinG to tHE FoLLoWinG
inStrUCtionS:
1. Turn the power switch on and increase the treadmill's
speed to 5 km/h (3 mph).
2. If the belt drifts to the left, turn the left adjustment
bolt ¼ turn clockwise and the right adjustment bolt 1/8
turn anti-clockwise. If the belt drifts to the right, turn
the right adjustment bolt ¼ turn clockwise and the left
adjustment bolt ¼ turn anti-clockwise.
3. If the belt remains centered the adjustment is correct.
If not, continue to make small adjustments as above
until the belt is correctly aligned. If the belt is allowed
run across to one side for long periods of time the edges
of the belt may be damaged and the treadmill may not
continue to operate correctly. Any damage to the belt
caused by the lack of necessary adjustment will not be
covered by the warranty.
ADJUSTING THE bELT TENSION
The belt must be tensioned if it begins to slip on the
rollers. In normal use, however, keep the belt as loose
as possible! The belt tension is adjusted by turning the
same screws as used for aligning the running belt. If
turning the screws will not effect the belt tension, please
contact your local Tunturi dealer.
1. Increase the treadmill's speed to 5 km/h (3 mph).
2. Turn both adjustment screws an equal amount, ¼
turn clockwise.
3. Try to slow the belt down by holding onto the
handrails and braking as you walk (as if you were
walking downhill).
If the belt slips, turn another ¼ turn and repeat the test.
When braking heavily the belt may slip. If the belt keeps
slipping despite repeated adjustments, please contact
your local Tunturi dealer.

MALFUNCTIONS

notE! Despite continuous quality control, defects
and malfunctions caused by individual components may
occur in the equipment. In most cases it's unnecessary
to take the whole device in for repair, as it's usually
sufficient to replace the defective part. Always give
the model, serial number of your equipment and in
case of malfunctions also conditions of use, nature of
malfunction and any error code.
When you encounter unusual behavior from the treadmill,
simply turn the power switch off, wait 1 minute and turn
the power switch on to reset the treadmill. This should
clear incidental errors and ready the treadmill for normal
operation again. If after you have reset the treadmill
by turning the power switch off and on again, and the
treadmill is still not operational, contact your local Tunturi
dealer for service.
If you require spare parts, always give the model, serial
number of your equipment and the spare part number for
the part you need. The spare part list is at the back of this
manual. Use only spare parts mentioned in the spare part
list.
ERROR CODES
The console will display information about operational
faults.
SPEED STALL / E1. Call the dealer for service.
SPEED RUNAWAY / E3. Ensure correct usage of the
treadmill. Do not push the belt with your feet. Turn the
power switch off, wait 1 minute and turn the power switch
on again. If treadmill recovers to normal operation, you
may continue to use the treadmill. Otherwise, call the
dealer for service.
LIFT MOTOR ERROR. If the lift motor works improperly,
the console's Elevation window will display "OFF". The
treadmill is still operational except the elevation function.
You can still use the treadmill. Ensure correct usage of the
treadmill. Do not overload the lift motor by continuously
changing the elevation. Turn the power switch off, wait 20
minutes and turn the power switch on again. If treadmill
does not recover to normal operation, call the dealer for
service.
If any other error codes show up, call the dealer for
service.
MOVING AND
STORAGE
You can fold up the T70/T80 treadmills to space saving
storage position.
notE! When folding the treadmill make sure the
running deck is at 0 degrees. If folding when the running
deck is angled, this might lead to damage.
Ensure the transportation wheels are sideways. Turn off the
power switch and unplug the power cord from the wall
and the treadmill. Take hold of the aluminium profile at
12