Strobe White Balance Adjustment - Sony MVC-FD100 Service Manual

MVC-FD100/FD100H/FD200/FD200H

17. Strobe White Balance Adjustment

Adjust the white balance when the strobe light flashed.
Mode
Subject
Measurement Point
Measuring Instrument
Adjustment Page
Adjustment Address
Specified Value
Note 1: Check that the data of page: 6, address: 02 is "00".
If not, turn the power of unit OFF/ON.
Note 2: Perform this adjustment in the Flash adjustment box.
Do not block the photocell window for flash.
Restrict external light to enter the photocell window for
flash as less as possible.
Note 3: Refer to "4. Preparing the Flash adjustment box".
(See page 5-7)
Note 4: The right four digits of the page: 1 displayed data of the
adjusting remote commander.
1:XX:XX
Note 5: Displayed data of page: F, address: 64 of the adjusting
remote commander.
F:XX:64
 Y level data
Note 6: "Strobe White Balance Adjustment" is available only
once after the power is turned on. Turn the power off,
then on again if the adjustment is retried.
Switch setting:
1) FLASH (Control button) .............. ON
Adjusting method:
Order Page Address Data
1
2 6 90
3 6 91
4 6 92
5 6 93
6 6 6C
7 6 2C
8 6 01
9 6 07
10 6 01
11
12 6 02
13 6 01
14 6 01
15
RadarW RadarW
RadarW RadarW RadarW
CAMERA
Flash adjustment box (Note 3)
(1 m from the front of lens)
Displayed data of page: 1 (Note
4) and page: F, address: 64
Adjusting remote commander
F
4D, 4E, 64, 69 to 6B
Y level data: 60 to 94 (Note 5)
R-Y level data:
FA to FF or 00 to 06 (Note 4)
B-Y level data:
FA to FF or 00 to 06 (Note 4)
B-Y level data
R-Y level data
Procedure
Perform "Data setting during
camera system adjustment".
(Refer to page 5-16)
00
00
FF
FF
01
01
79 Press PAUSE button.
Check the data changes to "01".
67 Press PAUSE button.
Check the flashing.
Check the data changes to "01".
00 Press PAUSE button.
67 Press PAUSE button.
Check the flashing.
Order Page Address Data
16 6 02
17 6 01
18 7 03
19 6 01
20
21 6 02
22
23 6 01
24 7 03
25 6 01
26
27 6 02
28 F 64
29 0 03
30 1
Note 7: The adjustment data will be automatically input to page:
F, address: 4D, 4E, 64 and 69 to 6B.
Note 8: Type of CCD imager is different according to the CD
board in MVC-FD100.
Refer to page 7 to discriminate the type of CCD.
Processing after Completing Adjustment:
Order Page Address Data
1 6 01
2 6 2C
3 6 6C
4 6 92
5 6 93
6 0 03
7
5-32
Procedure
Check the data changes to "01".
00 Press PAUSE button.
Press PAUSE button.
05
FD100: TYPE SO only (Note 8)
B9 Press PAUSE button. (Note 7)
Check the flashing.
Check the data changes to "01".
Wait for 3 seconds.
00 Press PAUSE button.
Press PAUSE button.
04
FD100: TYPE SO only (Note 8)
67 Press PAUSE button.
Check the flashing.
Check the data changes to "01".
Check that the data satisfies
the Y level data satisfied
value. (Note 5)
02
Check that the R-Y, B-Y
level data (Note 4) satisfies
the specified value.
Procedure
00 Press PAUSE button.
00
00
00
00
00
Release the data setting
performed at step 1.
(Refer to page 5-16)