Strobe White Balance Adjustment; Strobe Light Level And White Balance Check - Sony DSC-S70 Service Manual

13. Strobe White Balance Adjustment

Adjust the white balance when the strobe light flashed.
Mode
Subject
Adjustment Page
Adjustment Address
Note 1: Perform "Flange Back Adjustment", "Light Level
Adjustment", "Auto White Balance Adjustment" and
"Auto White Balance Standard Data Input" before this
adjustment.
Note 2: Perform this adjustment in the Flash adjustment box.
Note 3: Refer to "4. Preparing the Flash adjustment box".
(See page 5-7)
Note 4: Check that the data of page: 6, address: 02 is "00".
If not, turn the power of unit OFF/ON.
Switch setting:
1) FLASH ......................
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 5, address: F1, and set data: FF.
3) Select page: D, address: 63, set data: 40, and press the PAUSE
button of the adjusting remote commander.
4) Perform " Data setting during camera system adjustment".
(Refer to page 5-13)
5) Select page: 7, address: 03, and set data: 08.
6) Select page: 6, address: 90, and set data: 00.
7) Select page: 6, address: 91, and set data: 00.
8) Select page: 6, address: 92, and set data: 00.
9) Select page: 6, address: 93, and set data: 80.
10) Select page: 6, address: 6C, and set data: 01.
11) Select page: 6, address: 2C, and set data: 01.
12) Select page: 6, address: 01, set data: 79, and press the PAUSE
button.
13) Select page: 6, address: 01, set data: 67, and press the PAUSE
button.
14) Select page: 6, address: 01, set data: 00, and press the PAUSE
button.
15) Select page: 6, address: 01, set data: 79, and press the PAUSE
button.
16) Select page: 6, address: 01, set data: 67, and press the PAUSE
button.
17) Select page: 6, address: 01, set data: 00, and press the PAUSE
button.
18) Select page: 6, address: 01, set data: 79, and press the PAUSE
button.
19) Select page: 6, address: 01, set data: B9, and press the PAUSE
button. (The strobe white balance adjustment is performed
and the adjustment data is stored in page: F, address: 4D, 4E,
64, 69, 6A and 6B)
20) Select page: 6, address: 02, and check that the data is "01".
Processing after Completing Adjustments:
1) Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjusting remote commander.
2) Perform "Strobe Light Level and White Balance Check" suc-
cessively. (Do not turn the power of unit OFF)
STILL
Flash adjustment box (Note 3)
(1.0 m from the front of lens)
F
4D, 4E, 64, 69, 6A, 6B
ON

14. Strobe Light Level and White balance Check

Check the light level regulation and the white balance when the
strobe light flashed.
Mode
Subject
Measurement Point
Measuring Instrument Adjusting remote commander
Specified value
Note 1: Perform this checking successively after performing
"Flange Back Adjustment", " Light Level Adjustment", "Strobe
White Balance Adjustment" and "Auto White Balance Standard
Data Input". (Do not turn the power of unit OFF)
Note 2: Perform this adjustment in the Flash adjustment box.
Note 3: Refer to "4. Preparing the Fiash adjustment box".
(See page 5-7)
Note 4: The right four digits of the page: 1 displayed data of the
adjusting remote commander.
1:XX:XX
 R-Y level data
Note 5: Displayed data of page: F, address: 64 of the adjusting
remote commander.
F:XX:64
 Y level data
Note 6: Check that the data of page: 6, address: 02 is "00".
Checking method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 6, address: 01, set data: 79, and press the PAUSE
button of the adjusting remote commander.
3) Select page: 6, address: 01, set data: 67, and press the PAUSE
button.
4) Check the flashing of strobe light.
5) Select page: F, address: 64, and check that the data satisfies
the Y level data specified value. (Note 5)
6) Select page: 0, address: 03, and set data: 02.
7) Select page: 1, and check the R-Y, B-Y level data (Note 4)
satisfies the specified value.
Processing after Completing Adjustments:
1) Select page: 0, address: 03, and set data: 00.
2) Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjusting remote commander.
3) Select page: 6, address: 2C, and set data: 00.
4) Select page: 6, address: 6C, and set data: 00.
5) Select page: 6, address: 93, and set data: 00.
6) Select page: 7, address: 03, set data: 00, and press the PAUSE
button.
7) Select page: 5, address: F1, and set data: 00.
8) Select page: D, address: 63, set data: 00, and press the PAUSE
button.
9) Release the data setting performed at step 4) of "Strobe White
Balance Adjustment". (Refer to page 5-13)
10) Select page: 0, address: 01, and set data: 00.
5-23
STILL
Flash adjustment box (Note 3)
(1.0 m from the front of lens)
Displayed data of page: 1
Y level data: 60 to 94
R-Y level data: FA to FF or 00 to 06
(Note 4)
B-Y level data: FA to FF or 00 to 06
(Note 4)
 B-Y level data