Sony MVC-FD97 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Digital Camera
  5. FD Mavica MVC-FD97
  6. Service manual
Sony MVC-FD97 Service Manual

Sony MVC-FD97 Service Manual

Digital still camera
Hide thumbs Also See for MVC-FD97:
Table of Contents

Advertisement

Quick Links

SERVICE MANUAL
Level 2
Ver 1.1 2001. 06
This service manual contains information for Japanese model as well.
When the machine needs to be repaired,
please refer to page 6 to discriminate the
type of LCD.
On the FC-85 board
This service manual procides the information that is premised the
circuit board replacement service and not intended repair inside the
FC-85 board.
Therefore, schematic diagram, printed wiring board and electrical
parts list of the FC-85 board is not shown.
The following pages are not shown.
System
Image device
6.64 mm (1/2.7 type) color
CCD
Lens
×
10 zoom lens
f = 6.0 – 60.0 mm (1/4 –
2 3/8 inches)
(39 – 390 mm
(1 9/16 – 15 3/8 inches)
when converted into a
35 mm still camera)
F = 2.8
Exposure control
Automatic exposure
White balance
Automatic, Indoor, Outdoor,
One-push
Data system
Movie: MPEG
Still: JPEG, GIF (in TEXT
mode, Clip Motion), TIFF
Audio with still image:
MPEG (Monaural)
MVC-FD97
FC-85 board
Schematic diagram ..................................... Page 4-15 to 4-38
Printed wiring board ................................... Page 4-11 to 4-14
Electrical parts list ...................................... Page 6-11 to 6-18
The above-described information is shown in service manual
Level 3.
SPECIFICATIONS
Recording medium
Floppy disk:
3.5 inch 2HD MS-DOS
format (1.44 MB)
"Memory Stick"
Flash
Recommended recording
distance:
0.6 m to 2.5 m (23 5/8 inches
to 8 1/3 feet)
Input and Output
connector
A/V OUT (MONO)
(Monaural)
Minijack Video:
1 Vp-p, 75 Ω, unbalanced,
sync negative
Audio: 327 mV (at a 47 kΩ
load)
Output impedance: 2.2 kΩ
ACC jack
Minijack
US Model
Canadian Model
AEP Model
UK Model
E Model
Hong Kong Model
Australian Model
Korea Model
Japanese Model
USB jack
mini-B
LCD screen
LCD panel
TFT (Thin Film Transistor
active matrix) drive
Total number of dots
123 200 (560×220) dots
Finder
LCD panel
TFT (Thin Film Transistor
active matrix) drive
Total number of dots
180 000 (800×225) dots
– Continued on next page –
DIGITAL STILL CAMERA

Advertisement

Table of Contents
loading

Related Manuals for Sony MVC-FD97

Summary of Contents for Sony MVC-FD97

  • Page 1 MVC-FD97 SERVICE MANUAL US Model Canadian Model Level 2 AEP Model UK Model E Model Hong Kong Model Ver 1.1 2001. 06 Australian Model Korea Model Japanese Model This service manual contains information for Japanese model as well. When the machine needs to be repaired, please refer to page 6 to discriminate the type of LCD.
  • Page 2 Built-in microphone Electret condenser Capacity 5.0 Wh (700 mAh) microphone Built-in speaker Dynamic speaker • Floppy disk that can be used by the MVC-FD97 • Size : 3.5-inch • Type : 2 HD • Capacity : 1.44 MB • Format : MS-DOS format (512 bytes ×...

  • Page 3: Table Of Contents

    TABLE OF CONTENTS Section Title Page Section Title Page SERVICE NOTE PK-55 Printed Wiring Board .......... 4-43 ..............5 PK-55 (MODE SWITCH, A/V OUT) Schematic Diagram ............4-47 Self-diagnosis Display ............. 7 PK-55 (LCD DRIVE) Schematic Diagram ..... 4-49 PK-55 (LCD TIMING GENERATOR) Schematic Diagram ............
  • Page 4 Section Title Page 19. CCD White Defect Compensation ........ 5-33 20. Steady Shot Adjustment ..........5-34 1-5. Color Electronic Viewfinder System Adjustments ..5-37 EVF Initial Data Input ............ 5-37 VCO Adjustment (VF-141 Board) ......... 5-38 Bright Adjustment (VF-141 Board) ........ 5-39 Contrast Adjustment (VF-141 Board) ......

  • Page 5: Service Note

    (Part code: charged voltage which is kept without discharging when the main 1-215-869-11) power of the MVC-FD97 is simply turned off. Therefore, the re- maining voltage must be discharged as described below. Preparing the Short Jig To preparing the short jig. a small clip is attached to each end of a resistor of 1 kΩ...
  • Page 6 [LCD type check] By measuring the resistor value between Pin qd of CN803 and Pin 4 of CN803 on FC-85 board, the type of LCD can be discrimi- nated. Note: About PK-55 board and LCD module, discriminate LCD type on the machine, and replace the same type. FC-85 board CN803 Resistor LCD type...

  • Page 7: Self-Diagnosis Display

    DISK ERROR C:13:01 Format the floppy disk or “Memory Stick” • Data is damaged. MEMORY STICK ERROR with the MVC-FD97. • Unformatted disk or “Memory Stick” is inserted. Flash LED Checking of flash unit or replacement of Abnormality when flash is being...

  • Page 8: General

    You are cautioned that any changes or modifications not expressly approved This symbol is intended to For the Sony Service Center nearest you call The electromagnetic fields at the specific in this manual could void your alert the user to the presence...

  • Page 9: Identifying The Parts

    “InfoLITHIUM” is a lithium ion battery pack which can exchange information such as battery Charging at a room temperature of 10°C to 30°C (50°F to 86°F) is recommended. consumption with compatible video equipment. “InfoLITHIUM” L series battery packs have the mark. “InfoLITHIUM” is a trademark of Sony Corporation.

  • Page 10: Setting The Date And Time

    (mains). Using a car battery EFFECT FILE CAMERA SETUP SELECT MENU BAR OFF Use Sony DC adaptor/charger. Select [SETUP] with on the control button, Using your camera abroad then press the center For details, see page 76. VIDEO OUT /LANGUAGE...

  • Page 11: Inserting A Floppy Disk

    If you release the shutter button, the recording will be canceled. Terminal AE lock indicator (green) flashes t lights up Write-protect LOCK switch Label space The position or shape of the write-protect switch depends on the type of the “Memory Stick.” “Memory Stick” and are trademarks of Sony Corporation.
  • Page 12 Turning off the LCD screen Press the shutter button fully down. The shutter clicks. “RECORDING” appears on the LCD screen or on the Press LCD ON/OFF switch to turn off the LCD screen. The battery life will be finder, and the image will be recorded on the floppy disk or the “Memory longer.

  • Page 13: Recording Moving Images

    Notes Using the self-timer • The recommended shooting distance is 0.6 to 2.5 m (23 5/8 inches to 8 1/3 feet). • Attaching a conversion lens (not supplied) may block the light from the flash and the recorded When you use the self-timer function, the subject is recorded 10 seconds after you image may be eclipsed.

  • Page 14: Playing Back Moving Images

    Playing back moving images Select the (playback) button on the LCD B (playback)/ screen or on the finder with X (pause) button the control button, then press the center 120min 0:05 The moving image and sound are played back. During playback, (playback) changes to Access lamp (pause).
  • Page 15 (drag and drop). Click “USB Driver Installation for Windows 98/98SE, Windows Me, Windows 2000”. • Sony USB Driver USB driver installation starts. • Sony USB Shim Follow the on-screen messages to install the USB driver. When “Put these items into the Extensions folder?” appears, click “OK.”...

  • Page 16: Image File Storage Destinations And Image File Names

    Image file storage destinations Notes on using your computer and image file names Floppy disk/“ Memory Stick ” • Format the floppy disk or “Memory Stick” only using this camera Image files recorded with your camera are grouped in folders by recording mode. (page 72).

  • Page 17: Before Performing Advanced Operations

    Advanced operations Folder File Meaning Before performing advanced Imcif100 DSC0 ssss .JPG • Small-size image file recorded in E- operations MAIL mode (page 51) ssss • Uncompressed image file recorded in DSC0 .TIF TIFF mode (page 53) This section describes the basic control methods that are frequently used for “Advanced operations.”...
  • Page 18 Menu settings Item Setting Description PLAY/STILL/ MOVIE selector Menu items that can be modified differ depending on the positions of the PLAY/ STILL/MOVIE selector or the MS/FD selector. The LCD screen or the finder shows FORMAT Formats a “Memory Stick.” Once you PLAY only the items you can operate at the moment.

  • Page 19: Various Recording

    B Various recording Item Setting Description PLAY/STILL/ ∗ The image is recorded in the ratio of MOVIE selector three to two to fit the printing paper size. Using this image size, the Setting the image size VIDEO NTSC Sets the video output signal to NTSC PLAY margin of an image is not printed out.
  • Page 20 The number of images that you Recording still Adding audio files to Recording text can record on a floppy disk or “Memory Stick” (8 MB) in VOICE images for e-mail (E- still images (VOICE) documents (TEXT) mode MAIL) Images in VOICE mode are recorded Text is recorded in GIF format to Image size Number of images*...
  • Page 21 Notes Focusing manually Using the PROGRAM Twilight mode • Focal point information may not Suppresses the blurring of colors completely show the correct distance. Use AE function Normally the focus is automatically the information as a guide. of a bright subject in a dark place •...

  • Page 22: Various Playback

    Shoot a white object such as paper Adjusting the white Recording the date Enjoying picture full under the same situation you balance (WHITE and time on the still effects (PICTURE will shoot. Press BALANCE) image (DATE/TIME) EFFECT) indicator flashes quickly. When the white balance has been Normally the white balance is adjusted and stored in the memory,...

  • Page 23: Editing

    To skip to the next/previous Playing back the still Viewing images on a image during the slide show images in order TV screen Select at the lower-left on the (SLIDE SHOW) LCD screen or on the finder. Before connecting your camera, be sure to turn off the TV.
  • Page 24 Notes Select the media that the Changing the Copying images • You cannot change the size of images image will be copied onto. recorded in TEXT mode, moving images, recorded still image (COPY) • When the MS/FD selector is set uncompressed images, or Clip Motion size (RESIZE) to FD.

  • Page 25: As An External Drive

    Insert another floppy disk. Select [ENTER]. Selecting still images Format “RECORDING” appears. When marks on the selected to print (PRINT MARK) copying is completed, images change from green to When you format a floppy disk or “COMPLETE” appears. white. “Memory Stick,” all data stored on the You can mark a print mark on still To end copying, select [EXIT].
  • Page 26 (mains lead), pull it • Keep the battery pack dry. Stick” with your hand or a metal object. camera and contact your nearest Sony out by the plug. Never pull the power • Do not strike, bend or drop the “Memory •...

  • Page 27: Troubleshooting

    The picture is noisy. • Your camera is placed near a TV or other Sony dealer or local authorized Sony service facility. If code displays (C: equipment that uses strong magnets. appear on the LCD screen or on the finder, the self-diagnosis display function is Move your camera away from the TV, etc.

  • Page 28: Warning And Notice Messages

    • A malfunction has occurred in the battery pack. System properties is displayed. Click the [Hardware] tab located at the top, (CHG) lamp flashes when Contact your Sony dealer or local authorized then click the [Device Manager (D)] button. charging a battery pack.

  • Page 29: Self-Diagnosis Display

    If you are unable to rectify the problem even if you try corrective actions a K Iris/Shutter speed indicator few times when C: ss : ss is indicated, contact your Sony dealer or local authorized Sony service facility. L AE lock indicator/Focus lock...

  • Page 30: Disassembly

    MVC-FD97 SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. MVC-FD97 2-1. TOP CABINET BLOCK 2-2. EVF BLOCK ASSEMBLY 2-3. VF LENS ASSEMBLY 2-4. VF-143 BOARD ASSEMBLY (Page 2-2) (Page 2-2) (Page 2-2) (Page 2-2) 2-5.

  • Page 31: Top Cabinet Block Assembly

    Note: Follow the disassembly procedure in the numerical order given. 2-1. TOP CABINET BLOCK ASSEMBLY 2-3. VF LENS ASSEMBLY 2 Screw 3 Screw 7 Top cabinet (M2) (M2) block assembly 4 Screw 2 VF cabinet assembly (M2) 4 VF lens assembly 3 Flexible board (CN501) 8 Flexible board...

  • Page 32: Cabinet (Rear) Block Assembly

    [SERVICE POSITION (EVF)] VF-143 board VF lens assembly : Contacting surface AC power AC IN adaptor Base Adjustment remote commander CPC-12 jig (J-6082-436-A) 2-5. CABINET (REAR) BLOCK ASSEMBLY 2-6. PK-55 BOARD 2 Flexible board (CN781) 3 Screw 5 Cabinet (rear) (M2) block assembly 1 Two screws...

  • Page 33: Lcd Module

    2-7. LCD MODULE 4 Speaker 6 LCD module 1 Two screws 5 Cold cathode fluorescent tube 2 Two screws 3 BL fixed plate [SERVICE POSITION (PK-55 BOARD AND LCD PANEL)] : Contacting surface Cold cathode LCD panel Insulating sheet fluorescent tube AC power AC IN adaptor...

  • Page 34: Fdd Block Assembly

    2-8. FDD BLOCK ASSEMBLY 2-10. LENS COMPLETE BLOCK ASSEMBLY 4 FDD block assembly 5 Harness 2 Two flexible board 1 Four screws (CN004) (CN182, 401) (M2) 1 Harness (CN003) 2 Remove the lens complete assembly in the direction of the arrow. 3 Two flexible board (CN101, 183) 2-9.

  • Page 35: Board

    2-12. VP-55 BOARD 2-13. LENS BLOCK ASSEMBLY 1 Screw 2 Screw 4 Clow (M2) (M2) 2 Boss 3 Boss 6 Cabinet (LT) qs Screw 5 Clow (M2) qa VP fixed plate qd Screw (M2) 1 Two screws 4 Lens block assembly 3 Screw qf VP-55 board (M2)

  • Page 36: Board

    2-14. FC-85 BOARD 2-15. CF-83 BOARD 5 Four screws 1 Screw 7 FC-85 board (M2) (M2) 3 CF-83 board 6 Claw Two switches (S402, 403) Two SS knobs 2 Two claws 4 Three flexible 2 Screw boards (M2) (CN701, 702, 703) 1 Flexible board Note: When installing CF-83 board, connect two switches (CN682)

  • Page 37: Circuit Boards Location

    2-16. CIRCUIT BOARDS LOCATION VF-143 LCD DRIVE, TIMING FLASH UNIT GENERATOR, BACK LIGHT MA-404 (MIC AMP) FU-153 (DC IN) AE-25 (CONTROL SWITCH) FC-85 CAMERA PROCESS, CAMERA DSP, VIDEO, MEMORY, LENS DRIVE, SH DSP, USB I/F, MS SOCKET, FDD INTERFACE, FDD CONTROL, HI CONTROL, AUDIO, DC/DC CONVERTER CD-311 (CCD IMAGER, STEADY SHOT SENSOR)

  • Page 38: Flexible Boards Location

    2-17. FLEXIBLE BOARDS LOCATION Control switch block FP-174 FP-171 FP-176 LCD901 FP-168 FP-335 ND801 Lens assembly FP-175 VAP assembly FP-173 LCD902 FP-177 FP-166 FP-172 FP-169 FP-170 2-9 E...

  • Page 39: Block Diagrams

    MVC-FD97 SECTION 3 BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM CD-311 BOARD (1/2) FC-85 BOARD LENS IRIS METER IC102 FILTER IC101 IC702 IC704 CCD OUT S/H, AGC, DATA BUS 12 REC/PB AMP, FLOPPY CCD IMAGER A/D CONV. IC301 CONTROL STEPPING (SEE PAGE 4-8)

  • Page 40: Power Block Diagram 1

    MVC-FD97 3-12. POWER BLOCK DIAGRAM 1 FU-153 BOARD FC-85 BOARD (1/2) CN801 (2/2) (SEE PAGE 4-68) EVER 3.2V EVER 3.2V J001 CN004 CN001 CN001 DC IN F003 BL UNREG BL UNREG ACV UNREG BL UNREG BATT/XEXT F001 PANEL 13.2V ST UNREG...

  • Page 41: Power Block Diagram 2

    MVC-FD97 3-13. POWER BLOCK DIAGRAM 2 MA-404 BOARD CONTROL SWITCH BLOCK VF-143 BOARD (SEE PAGE 4-62) IC504 IC503 SHOCK CN402 CN301 IC301 DETECT (D/A CONVERTER) A 4.9V MIC AMP (SEE PAGE 4-57) (SEE PAGE 4-58) RV001 IC603 IC604 (SEE PAGE 4-62)

  • Page 42: Power Block Diagram 3

    MVC-FD97 3-14. POWER BLOCK DIAGRAM 3 TYPE S/C model: Please refer to page 6 to discriminate the type of LCD. TYPE S TYPE C PANEL PANEL PK-55 BOARD (2/2) UNIT UNIT CN701 (2/2) CN901 CN901 L901 PANEL 13.2V L902 PANEL –15.3V...

  • Page 43: Printed Wiring Boards And Schematic Diagrams

    MVC-FD97 SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) (Measuring conditions voltage and waveform) •...

  • Page 44: Frame Schematic Diagrams

    MVC-FD97 4-1. FRAME SCHEMATIC DIAGRAMS FRAME SCHEMATIC DIAGRAM (1/2) J001 S355 CN001 DC IN PROGRAM AE ACV_UNREG S351 SPOT METER ACV_GND BATT/XEXT FLOPPY DISK DRIVE S352 BT901 S356 BATTERY TERMINAL FU-153 BOARD PROGRAM AE ONE-PUSH WHITE BALANCE CN002 AE-25 BOARD...

  • Page 45: Frame Schematic Diagram (2/2)

    MVC-FD97 FRAME SCHEMATIC DIAGRAM (2/2) OPEN ND801 (FLASH) FLASH UNIT (FOR CHECK) BACK LIGHT CN801 CN701 AV_JACK_IN AV_JACK_IN VIDEO_OUT VIDEO_OUT VIDEO_GND VIDEO_GND AUDIO_OUT AUDIO_OUT VF-143 BOARD AUDIO_GND AUDIO_GND CN501 REG_GND REG_GND CN601 CN802 PK-55 BOARD XHI_SCK LANC_SIG LANC_SIG XHI_SCK CN901...

  • Page 46: Printed Wiring Boards And Schematic Diagrams

    MVC-FD97 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS CD-311 (CCD IMAGER, STEADY SHOT SENSOR) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM • See page 4-69 for waveforms. – Ref. No.: CD-311 board; 2,000 series – CD-311 BOARD (1/2) • For Printed Wiring Board.

  • Page 47: Steady Shot Sensor) Schematic Diagram

    MVC-FD97 CD-311 (STEADY SHOT SENSOR) SCHEMATIC DIAGRAM • See page 4-7 for CD-311 printed wiring board. CD-311 BOARD (2/2) STEADY SHOT SENSOR(SENSOR BLOCK) -REF.NO.:2,000 SERIES- XX MARK:NO MOUNT NO MARK:REC/PB MODE R:REC MODE P:PB MODE R160 R157 C152 R150 C163 0.022u...
  • Page 48 MVC-FD97 VP-55 (STEADY SHOT CONTROL) PRINTED WIRING BOARD – Ref. No.: VP-55 board; 2,000 series – • For Printed Wiring Board. • VP-55 board is four-layer print board. However, the patterns of layers 2 to 3 have not been included in the diagram.

  • Page 49: Vp-55 Printed Wiring Board

    MVC-FD97 VP-55 (STEADY SHOT CONTROL) SCHEMATIC DIAGRAM • See page 4-39 for VP-55 printed wiring board. • See page 4-71 for Waveforms. VP-55 BOARD IC206,207 INVERTER STEADY SHOT CONTROL L207 R238 10uH C225 -REF.NO.:2,000 SERIES- R252 R253 0.022u XX MARK:NO MOUNT...
  • Page 50 MVC-FD97 PK-55 (MODE SWITCH, A/V OUT, LCD DRIVE, LCD TIMING GENERATOR, BACK LIGHT DRIVE) PRINTED WIRING BOARD – Ref. No.: PK-55 board; 2,000 series – • For Printed Wiring Board. • PK-55 board is four-layer print board. However, the patterns of layers 2 to 3 have not been included in the diagram.
  • Page 51 MVC-FD97 DISPLAY (CHARGE) POWER ON/OFF CONTROL AV OUT (POWER) FLASH (FLASH) VOLUME(–) VOLUME ON/OFF 4-46 MODE SWITCH, A/V OUT, LCD DRIVE, LCD TIMING GENERATOR, BACK LIGHT DRIVE 4-45 PK-55...

  • Page 52: Mode Switch, A/V Out

    MVC-FD97 PK-55 (MODE SWITCH, A/V OUT) SCHEMATIC DIAGRAM • See page 4-43 for PK-55 printed wiring board. PK-55 BOARD (1/4) MODE SWITCH,A/V OUT(LK BLOCK,JACK BLOCK) SIGNAL PATH -REF.NO.:2,000 SERIES- VIDEO SIGNAL AUDIO XX MARK:NO MOUNT SIGNAL NO MARK:REC/PB MODE CHROMA Y/CHROMA PANEL_3.2V...

  • Page 53: Lcd Drive) Schematic Diagram

    MVC-FD97 PK-55 (LCD DRIVE) SCHEMATIC DIAGRAM • See page 4-43 for PK-55 printed wiring board. • See page 4-71 for waveforms. PK-55 BOARD (2/4) LCD DRIVE(RGB BLOCK) -REF.NO.:2,000 SERIES- XX MARK:NO MOUNT NO MARK:REC/PB MODE R812 *R817 :TYPE S 5600...

  • Page 54: Lcd Timing Generator) Schematic Diagram

    MVC-FD97 PK-55 (LCD TIMING GENERATOR) SCHEMATIC DIAGRAM • See page 4-43 for PK-55 printed wiring board. • See page 4-71 for waveforms. PK-55 BOARD (3/4) LCD TIMING GENERATOR(TG BLOCK) -REF.NO.:2,000 SERIES- XX MARK:NO MOUNT NO MARK:REC/PB MODE < >:TYPE S MODEL(REC/PB MODE)

  • Page 55: Back Light Drive) Schematic Diagram

    MVC-FD97 PK-55 (BACK LIGHT DRIVE) SCHEMATIC DIAGRAM • See page 4-43 for PK-55 printed wiring board. • See page 4-71 for waveforms. PK-55 BOARD (4/4) BACK LIGHT DRIVE(BL BLOCK) -REF.NO.:2,000 SERIES- Q856 XX MARK:NO MOUNT FP102-TL ND801 SWITCHING T851 L853...
  • Page 56 MVC-FD97 VF-143 (LCD DRIVE, TIMING GENERATOR, EVF LCD, BACK LIGHT) PRINTED WIRING BOARD – Ref. No.: VF-143 board; 2,000 series – • For Printed Wiring Board. • VF-143 board is six-layer print board. However, the patterns of layers 2 to 5 have not been included in the diagram.

  • Page 57: Vf-143 Printed Wiring Board

    MVC-FD97 VF-143 (LCD DRIVE) SCHEMATIC DIAGRAM • See page 4-55 for VF-143 printed wiring board. • See page 4-72 for waveforms. VF-143 BOARD(1/2) LCD DRIVER(VF1 BLOCK) R517 -REF.NO.:2,000 SERIES- XX MARK:NO MOUNT R525 R527 R511 R513 R516 R520 R518 NO MARK:REC/PB MODE...

  • Page 58: Timing Generator, Evf Lcd, Back Light) Schematic Diagram

    MVC-FD97 VF-143 (TIMING GENERATOR, EVF LCD, BACK LIGHT) SCHEMATIC DIAGRAM • See page 4-55 for VF-143 printed wiring board. • See page 4-72 for waveforms. VF-143 BOARD(2/2) TIMING GENERATOR,EVF LCD,BACK LIGHT (VF2 BLOCK) -REF.NO.:2,000 SERIES- XX MARK:NO MOUNT NO MARK:REC/PB MODE...
  • Page 59 MVC-FD97 MA-404 (MIC AMP) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM – Ref. No.: MA-404 board; 2,000 series – • For Printed Wiring Board. MA-404 BOARD • MA-404 board is four-layer print board. However, the patterns of layers 2 to 3 have not been included in the diagram.

  • Page 60: Parts Location

    MVC-FD97 AE-25 (CONTROL SWITCH) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM – Ref. No.: AE-25 board; 2,000 series – • For Printed Wiring Board. • AE-25 board is four-layer print board. However, the patterns S351 of layers 2 to 3 have not been included in the diagram.
  • Page 61 MVC-FD97 CF-83 (CONTROL SWITCH) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM – Ref. No.: CF-83 board; 2,000 series – • For Printed Wiring Board. • CF-83 board is four-layer print board. However, the patterns CF-83 BOARD of layers 2 to 3 have not been included in the diagram.
  • Page 62 MVC-FD97 FU-153 (DC IN) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM – Ref. No.: FU-153 board; 2,000 series – • For Printed Wiring Board. • FU-153 board is four-layer print board. However, the patterns of layers 2 to 3 have not been included in the diagram.

  • Page 63: Waveforms

    4-3. WAVEFORMS CD-311 BOARD 8.0 Vp-p 104 µsec IC101 1, 2, 3 REC 8.0 Vp-p 104 µsec IC101 4, 5, 6 REC 1.0 Vp-p 104 µsec IC101 8 REC 5.0 Vp-p 18.4 MHz IC101 qf REC 5.0 Vp-p 17.1 MHz IC101 qg REC 4.2 Vp-p 17.1 MHz...
  • Page 64 VP-55 BOARD PK-55 BOARD 2.8 Vp-p 6.0 Vp-p 500 mVp-p 480 MHz 12 MHz IC209 wf REC IC802 8 REC/PB IC851 1 REC/PB 300 mVp-p IC802 9 REC/PB 250 mVp-p IC802 0 REC/PB 4.6 Vp-p IC802 w; REC/PB 4.6 Vp-p IC802 ws REC/PB 4.6 Vp-p IC802 wf REC/PB...
  • Page 65 VF-143 BOARD 480 mVp-p 2.2 Vp-p 16.5 MHz IC502 8 REC/PB IC603 ra REC/PB 300 mVp-p 3.0 Vp-p IC502 9 REC/PB IC603 rg REC/PB 200 mVp-p IC502 0 REC/PB 8.8 Vp-p IC502 w; REC/PB 8.8 Vp-p IC502 ws REC/PB 8.8 Vp-p IC502 wf REC/PB 3.0 Vp-p IC502 wl REC/PB...

  • Page 66: Parts Location

    4-4. PARTS LOCATION CD-311 BOARD CD-311 BOARD (SIDE A) (SIDE B) C160 C101 C161 C102 C165 C103 C104 L150 C105 C106 R112 C107 C108 C109 C150 C151 C152 C153 C156 C157 C158 C159 C162 C163 C164 CN101 CN102 IC101 IC150 L101 Q101 Q102...
  • Page 67 VP-55 BOARD VP-55 BOARD PK-55 BOARD PK-55 BOARD (SIDE A) (SIDE B) (SIDE A) (SIDE B) R956 R862 C205 C201 BT701 C803 C207 C202 R957 C804 R863 C212 C203 C705 R961 C805 R865 C224 C204 C706 R962 C806 R866 R974 R873 C225 C206...
  • Page 68 VF-143 BOARD VF-143 BOARD AE-25 BOARD FU-153 BOARD FU-153 BOARD (SIDE A) (SIDE B) (SIDE B) (SIDE A) (SIDE B) C501 C520 CN351 CN001 C001 C502 C521 CN002 C503 C601 R351 CN003 CN004 C504 C602 R352 C505 C603 R353 FB001 D001 C506 C604...

  • Page 69: Adjustments

    MVC-FD97 SECTION 5 ADJUSTMENTS Before starting adjustment EVR Data Re-writing Procedure When Replacing Board The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.

  • Page 70: Adjusting Items When Replacing Main Parts And Boards

    1-1. Adjusting items when replacing main parts and boards When replacing main parts and boards, adjust the items indicated by z in the following table. Replaced parts Block Mounted parts Board replacement replacement replacement Adjustment section Adjustment Initialization of D page data Initialization of 7, B, D, E, F, page data Initialization of 7, B, E, F page data...

  • Page 71: Camera Section Adjustments

    5-1. CAMERA SECTION ADJUSTMENTS 1-1. PREPARATIONS BEFORE ADJUSTMENT 1-1-1. List of service tools • Oscilloscope • Regulated power supply • AC power adaptor (AC-L10A) • Digital voltmeter • Vectorscope • Color monitor Ref. No. Name Parts Code Usage Filter for color temperature correction (C14) J-6080-058-A Auto white balance adjustment/check White balance adjustment/check...

  • Page 72: Preparations

    1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Pattern box Note 2: When performing only the adjustments, the lens block and boards need not be disassemble. 1) Connect the equipment for adjustments according to Fig. 5-1- Front side of the lens 2) Connect the Adjusting remote commander to FC-85 board CN803 via CPC-12 jig (J-6082-436-A).
  • Page 73 VF-141 BOARD power adaptor AC IN FU-153 BOARD CN601 CN501 AE-25 BOARD Must be connected when the MIC UNIT is used. CN001 Need not CN351 connected MIC UNIT CN002 MF UNIT MA-404 BOARD CN004 CN303 CN003 FDD UNIT CN305 CN301 FLASH UNIT CN306...

  • Page 74: Precautions

    1-1-4. Precautions 1. Setting the Switch Unless otherwise specified, set the switches as follows and per- form adjustments. 1. PLAY/CAMERA/MOVIE switch (PK-55 board S708, S710) ........CAMERA 2. FOCUS AUTO/MANUAL switch (CF-83 board S402) ..........MANUAL 3. PROGRAM AE button (AE-25 board S354) ........

  • Page 75: Preparing The Flash Adjustment Box

    4. Preparing the Flash Adjustment Box A dark room is required to provide an accurate flash adjustment. If it is not available, prepare the flash adjustment box as given below; 1) Provide woody board A, B and C of 15 mm thickness. woody board A (2) woody board B (2) woody board C (1)

  • Page 76: Initialization Of B, D, E, F

    1-2. INITIALIZATION OF B, D, E, F, 7 PAGE DATA 3. D Page Table Note 1: Fixed data-1: Initialized data. 1-2-1. Initialization of D Page Data (Refer to “1. Initializing of D Page Data”) 1. Initializing D Page Data Note 2: Fixed data-2: Modified data. Note: If the D page data has been initialized, the following (Refer to “2.

  • Page 77: Initialization Of B, E, F, 7 Page Data

    1-2-2. Initialization of B, E, F, 7 Page Data 3. B Page Table 1. Initializing B, E, F, 7 Page Data Note 1: Fixed data-1: Initialized data. Note: If the B, E, F Page data has been initialized, “Modification (Refer to “1. Initializing B, E, F, 7 Page Data”) Note 2: Fixed data-2: Modified data.

  • Page 78: F Page Table

    5. F Page Table Note 1: Fixed data-1: Initialized data. (Refer to “1.Initializing of B, E, F, 7 Page Data”) Note 2: Fixed data-2: Modified data. (Refer to “2.Modification of B, E, F, 7 Page Data”) Address Initial value Remark Address Initial value Remark White balance ND filter compensation...
  • Page 79 Address Initial value Remark Mixed color cancel adj. A4 to AB Fixed data-1 (Initialized data) Steady shot adj. (2) Steady shot adj. (1) AE to AF Fixed data-1 (Initialized data) B0 to FF Fixed data-2 5-11...

  • Page 80: Page Table

    6. 7 Page Table Note 1: Fixed data-1: Initialized data. (Refer to “1. Initializing B, E, F, 7 Page Data”) Note 2: Fixed data-2: Modified data. (Refer to “2. Modification of B, E, F, 7 Page Data”) Address Initial value Remark Address Initial value...

  • Page 81: Video System Adjustments

    1-3. VIDEO SYSTEM ADJUSTMENTS 2. Video Burst Level Adjustment Adjust the burst level of the composite video signal output. 1. Video Sync Level Adjustment Adjust the sync level of the composite video signal output. Mode PLAY Mode PLAY Signal Arbitrary Signal Arbitrary Measurement Point...

  • Page 82: Camera System Adjustment

    1-4. CAMERA SYSTEM ADJUSTMENT Before perform the camera system adjustments, check that the specified values of “VIDEO SYSTEM ADJUSTMENTS” are sat- isfied. Data setting during camera system adjustment Perform the following data setting before the camera system ad- justments. Data setting method: Order Page Address Data Procedure Press PAUSE button.

  • Page 83: Hall Adjustment

    1. HALL Adjustment Processing after Completing Adjustment: For detecting the position of lens iris, adjust the HALL AMP gain Order Page Address Data Procedure and offset. Mode CAMERA Press PAUSE button. Subject Not required Measurement Point Displayed data of page: 1 (Note 2) Measuring Instrument Adjusting remote commander Adjustment Page...

  • Page 84: Flange Back Adjustment (Using The Minipattern Box)

    2. Flange Back Adjustment (Using the minipattern box) Specified voltage: The specified voltage varies according to the The flange back of inner focus lens is adjusted automatically. If minipatternbox, so adjustment the power sup- shifted, the auto focus is disordered. ply output voltage to the specified voltage writ- ten on the sheet which is supplied with the mini- Mode...
  • Page 85 3. Flange Back Adjustment Adjusting method: (Using the flange back adjustment chart and a subject Order Page Address Data Procedure more than 500 m away) The flange back of inner focus lens is adjusted automatically. If shifted, the auto focus is disordered. Press PAUSE button.

  • Page 86: Flange Back Check

    3-2. Flange Back Adjustment (2) 4. Flange Back Check Perform this adjustment after performing “Flange Back Adjust- ment (1)”. Mode CAMERA Subject Siemens star Mode CAMERA (2.0 m from the front of the lens) Subject Subject more than 500 m away (Luminance: approx.

  • Page 87: F No. Standard Data Input

    6. Mechanical Shutter Adjustment 5. F No. Standard Data Input Adjust the period which the mechanical shutter is closed, and com- Compensate the unevenness of the iris meter sensitivity. pensate the exposure. Mode CAMERA Mode CAMERA Subject Clear chart Subject Clear chart (Color reproduction adjustment (10 cm from the front of the lens)

  • Page 88: Picture Frame Setting

    7. Picture Frame Setting How to reset the zoom and focus when they deviated: Order Page Address Data Procedure Mode CAMERA (Note 2) Subject Color bar chart (Note 2) (Color reproduction adjustment frame) (Note 3) Measurement Point Video terminal of A/V OUT jack (Note 3) (75 Ω...

  • Page 89: Light Level Adjustment And Nd Shutter Check

    8. Light Level Adjustment and ND Shutter Check Processing after Completing Adjustment: Adjust the standard LV value. Order Page Address Data Procedure Mode CAMERA Press PAUSE button. Subject Clear chart (Color reproduction adjustment frame) Press PAUSE button. Measurement Point Displayed data of page: 1 (Note 2) Release the data setting Measuring Instrument Adjusting remote commander...

  • Page 90: Mixed Color Cancel Adjustment

    9. Mixed Color Cancel Adjustment 10. Auto White Balance Standard Data Input Adjust the white balance standard data at 3200K. To perform mixed color cancel adjustment based on data of each color in color bar. Mode CAMERA Mode CAMERA Subject Clear chart (Color reproduction adjustment Subject...

  • Page 91: Auto White Balance Nd Filter Compensation

    11. Auto White Balance ND Filter Compensation Adjust to the proper auto white balance output data with Built-in ND filter. If it is not correct, auto white balance and color reproducibility will be poor. Mode CAMERA Subject Clear chart (Color reproduction adjustment frame) Adjustment Page Adjustment Address...

  • Page 92: Auto White Balance Adjustment

    12. Auto White Balance Adjustment Order Page Address Data Procedure Adjust to the proper auto white balance output data. Check that the displayed data If it is not correct, auto white balance and color reproducibility (Note 3) satisfied the R ratio will be poor.

  • Page 93: Color Reproduction Adjustment

    13. Color Reproduction Adjustment 13-2. Color Reproduction Adjustment (With ND Filter) Adjust the color separation matrix coefficient so that proper color Mode CAMERA reproduction is produced. Subject Color bar chart 13-1. Color Reproduction Adjustment (Without ND Filter) (Color reproduction adjustment frame) Mode CAMERA...

  • Page 94: Color Reproduction Check

    14. Color Reproduction Check Processing after Completing Adjustment: Order Page Address Data Procedure Mode CAMERA Press PAUSE button. Subject Color bar chart (Color reproduction adjustment frame) Set the data noted down at step 7, and press PAUSE Measurement Point Video terminal of A/V OUT jack (75 Ω...
  • Page 95 For NTSC mode Processing after Completing Adjustment: Order Page Address Data Procedure Press PAUSE button. Set the data noted down at step 8, and press PAUSE button. Set the data noted down at step 5, and press PAUSE button. Press PAUSE button. Release the data setting performed at step 4.

  • Page 96: Auto White Balance Check

    Ver 1.1 2001. 06 15. Auto White Balance Check Order Page Address Data Procedure INDOOR data check (with ND filter) Mode CAMERA Note down the data. Subject Clear chart (Color reproduction adjustment Press PAUSE button. frame) Measurement Point Displayed data of Video terminal Wait for 1 second.
  • Page 97 4 mm 4 mm Fig. 5-1-19 (A) 1 mm 1 mm 6 mm 6 mm Fig. 5-1-19 (B) 5-29...

  • Page 98: Strobe White Balance Adjustment

    16. Strobe White Balance Adjustment Adjust the white balance when the strobe light flashed. Mode CAMERA Subject Flash adjustment box (Note 3) (1.0 m from the front of lens) Adjustment Page Adjustment Address 4D, 4E, 64, 69, 6A, 6B Note 1: Perform “Hall Adjustment”, “Flange Back Adjustment”, “Light Level Adjustment”...

  • Page 99: Strobe Light Level And White Balance Check

    17. Strobe Light Level and White Balance Check Processing after Completing Adjustment: Check the light level regulation and the white balance when the Order Page Address Data Procedure strobe light flashed. Mode CAMERA Press PAUSE button. Subject Flash adjustment box (Note 3) (1.0 m from the front of lens) Measurement Point Displayed data of page: 1...

  • Page 100: Ccd Black Defect Compensation

    18. CCD Black Defect Compensation Processing after Completing Adjustment: Order Page Address Data Procedure Mode CAMERA Set data noted down at step Subject Clear chart 5, and press PAUSE button. (25 cm from the front of lens) Press PAUSE button. Measurement Point Displayed data of page: 6, address: 55...

  • Page 101: Ccd White Defect Compensation

    19. CCD White Defect Compensation Processing after Completing Adjustment: Order Page Address Data Procedure Mode CAMERA Set data noted down at step Subject Clear chart 5, and press PAUSE button. (25 cm from the front of lens) Set data noted down at step Measurement Point Displayed data of page: 6, 7, and press PAUSE button.

  • Page 102: Steady Shot Adjustment

    Adjusting method: 20. Steady shot adjustment • Perform the steady shot adjustment only when replacing the Order Page Address Data Procedure angular velocity sensor. When the microprocessor, circuit, etc. Expose pattern A with the zoom malfunctions, do not perform this adjustment but check opera- TELE end.
  • Page 103 Falling edge of Falling edge of waveform when waveform when data is “08” data is “09” t1 (µsec) Fig. 5-1-21 5-35...
  • Page 104 20-2. Steady Shot Adjustment (2) Processing after Completing Adjustment: Order Page Address Data Procedure Mode CAMERA Subject Pattern B Turn off the HOLD switch. (1.5 m from the front of the protection glass) Check that the steady shot operation is performed normally. Measurement Point Video output terminal Measuring Instrument...

  • Page 105: Color Electronic Viewfinder System Adjustments

    1-5. COLOR ELECTRONIC VIEWFINDER SYSTEM 1. EVF Initial Data Input ADJUSTMENTS Mode CAMERA Note 1: The back light (fluorescent tube) is driven by a high volt- Signal Arbitrary age AC power supply. Therefore, do not touch the back Adjustment Page light holder to avoid electrical shock.

  • Page 106: Vco Adjustment (Vf-141 Board)

    2. VCO Adjustment (VF-141 board) Set the VCO free-run frequency. If deviated, the EVF screen will be blurred. Mode CAMERA Subject Arbitrary Pin ws of CN803 (EVF_VCO) on Measurement Point FC-85 board Measuring Instrument Oscilloscope GND level (0 Vdc) Adjustment Page Fig.

  • Page 107: Bright Adjustment (Vf-141 Board)

    3. Bright Adjustment (VF-141 board) Pedestal Set the D range of the RGB driver used to drive the LCD to the specified value. If deviated, the EVF screen will become blackish or saturated (whitish). Mode CAMERA Subject Arbitrary Pin wa of CN803 (EVF_VG) on Measurement Point FC-85 board Measuring Instrument...

  • Page 108: Contrast Adjustment (Vf-141 Board)

    4. Contrast Adjustment (VF-141 board) Set the level of the VIDEO signal for driving the LCD to the speci- fied value. If deviated, the screen image will be blackish or satu- rated (whitish). 10 steps peak Mode CAMERA Subject Arbitrary Pin wa of CN803 (EVF_VG) on Measurement Point FC-85 board...

  • Page 109: Backlight Consumption Current Adjustment

    5. Backlight Consumption Current Adjustment 6. White Balance Adjustment (VF-141 board) (VF-141 board) Correct the white balance. Set the backlight luminance and color temperature. If deviated, the EVF screen color cannot be reproduced. If deviated, the image may become dark or bright. Mode CAMERA Mode...

  • Page 110: Lcd System Adjustments

    [Adjusting connector] 1-6. LCD SYSTEM ADJUSTMENTS Most of the measuring points for adjusting the LCD system are Before perform the LCD system adjustments, check that the concentrated in CN803 of the FC-85 board. specified values of “VIDEO SYSTEM ADJUSTMENTS” are sat- Connect the Measuring Instruments via the CPC-12 jig (J-6082- isfied.

  • Page 111: Lcd Initial Data Input

    1. LCD Initial Data Input Alignment disk (Disk-1, Disk-2) (A set of alignment disks consists of two disks as a pair.) Disk-1: 8-967-990-01 Mode PLAY (TFD2-1 (+)) (+17.5 µm) Signal Arbitrary Disk-2: 8-967-990-11 Adjustment Page (TFD2-2 (–)) (–17.5 µm) Adjustment Address D0 to D9, DC to DF [Common signals in the disks] Adjusting method:...

  • Page 112: Vco Adjustment (Fc-85 Board)

    2. VCO Adjustment (FC-85 Board) 3. D Range Adjustment (FC-85 Board) Set the VCO free-run frequency. If deviated, the LCD screen will Set the D range of the LCD driver to the specified value. be blurred. If deviated, the LCD screen will became blackish or saturated (whitish) Mode PLAY...

  • Page 113: Bright Adjustment (Fc-85 Board)

    4. Bright Adjustment (FC-85 Board) 5. Contrast Adjustment (FC-85 Board) Set the level of the VIDEO signal for driving the LCD to the speci- Set the level of the VIDEO signal for driving the LCD to the speci- fied value. fied value.

  • Page 114: Color Adjustment (Fc-85 Board)

    6. Color Adjustment (FC-85 Board) 7. V-COM Level Adjustment (FC-85 Board) Set the color saturation to the standard value. Set the common electrode drive signal level of LCD to the speci- If, deviated, the color will be dark or light. fied value.

  • Page 115: V-Com Adjustment (Fc-85 Board)

    8. V-COM Adjustment (FC-85 Board) 9. White Balance Adjustment (FC-85 Board) Set the DC bias of the common electrode drive signal of LCD to Correct the white balance. the specified value. If deviated, the LCD screen color cannot be reproduced. If deviated, the LCD display will be move, producing flicker and conspicuous vertical lines.

  • Page 116: System Control System Adjustments

    1-7. SYSTEM CONTROL SYSTEM ADJUSTMENTS Adjusting method: 1. Battery Down Adjustment Order Page Address Data Procedure Set the battery end voltage. If the voltage is incorrect, the life of battery will shorten. The image at the battery end will also be rough. Decrease the output voltage of the regulated power supply Mode...

  • Page 117: Zoom Center Adjustment

    2. ZOOM Center Adjustment 3. Eye Sensor Adjustment Set normal position (center value) of ZOOM lever. Mode CAMERA Mode CAMERA White chart (30 cm × 30 cm) Subject Subject Arbitrary Measurement Point Displayed data of page: 2, Measurement Point Displayed data of page: 2 address: 82 address: 5C (Note 2) Measuring Instrument...

  • Page 118: Eye Sensor Check

    4. Eye Sensor Check 5. Alignment Check (FDD Unit) Confirm that the FDD alignment is within the specifications. If Mode CAMERA deviated, reading and writing data from and to floppy disk be- White chart (30 cm × 30 cm) come impossible. Subject Or compatibility of floppy disk with other machines can be lost.

  • Page 119: Service Mode

    5-2. SERVICE MODE • Changing the address The address increases when the FF (M) button is pressed, 2-1. ADJUSTING REMOTE COMMANDER and decreases when the REW (M) button is pressed. There The adjusting remote commander is used for changing the calcu- are altogether 256 addresses, from 00 to FF.
  • Page 120 2-2. DATA PROCESS The calculation of the adjusting remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data.

  • Page 121: Remote Commander

    3. Switch Check (1) 2-3. SERVICE MODE 1. Setting the Test Mode Page 2 Address 43 Page D Address 10 Function When bit value=1 When bit value=0 Data Function XPOWER SW (PK-55 board S703) Normal XCAM/PLAY SW Forced CAMERA mode power ON PLAY CAMERA (PK-55 board S707)

  • Page 122: Switch Check (3)

    (Such as 2DD) DISK ERROR Format the floppy disk or “Memory Stick” • Data is damaged. MEMORY STICK ERROR with the MVC-FD97. • Unformatted disk or “Memory Stick” is inserted. Flash LED Checking of flash unit or replacement of Abnormality when flash is being...

  • Page 123: Repair Parts List

    MVC-FD97 SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS The components identified by mark 0 or dotted line with mark 0 are NOTE: critical for safety. • -XX and -X mean standardized parts, so they may • The mechanical parts with no reference number in Replace only with part number speci- fied.

  • Page 124: Top Cabinet Block Assembly

    6-1-2. TOP CABINET BLOCK ASSEMBLY EVF block assembly (See page 6-3.) supplied supplied MIC901 supplied supplied The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité.

  • Page 125: Evf Block Assembly

    6-1-3. EVF BLOCK ASSEMBLY LCD902 supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-678-327-12 FP-173 FLEXIBLE BOARD 3-060-836-11 KNOB, VISIBILITY ADJUSTMENT 3-060-922-01 LID, VF * 109 3-058-232-01 CUSHION (1) (97), LCD A-7074-453-A VF-143 BOARD, COMPLETE * 110 3-058-234-02 CUSHION (2) (97), LCD X-3950-617-1 LENS ASSY, VF...

  • Page 126: Lens Complete Assembly

    6-1-4. LENS COMPLETE ASSEMBLY Lens block assembly (See page 6-5.) J001 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3950-618-1 CABINET (LB) ASSY 1-678-330-11 FP-177 FLEXIBLE BOARD 3-060-893-01 COVER, DC IN 3-968-729-51 SCREW (M2), LOCK ACE, P2 3-060-914-01 HOLDER, DC A-7074-793-A VP-55 BOARD, COMPLETE 3-948-339-61 TAPPING...

  • Page 127: Lens Block Assembly

    6-1-5. LENS BLOCK ASSEMBLY IC101 (Note 1) supplied supplied (Note 1) Be sure to read “Precuations for Replacement of CCD Imager” on page 4-8 when changing the CCD imager. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7074-792-A CD-311 BOARD, COMPLETE 3-709-575-01 VAP ASSY...

  • Page 128: Cabinet (Front) Block Assembly

    6-1-6. CABINET (FRONT) BLOCK ASSEMBLY BT901 supplied supplied supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3951-506-1 CABINET (FRONT) ASSY * 264 3-058-801-01 SHEET, ST INSULATING 3-060-842-02 LID, BATTERY 3-736-363-41 TAPPING 3-058-748-01 KNOB, B LOCK * 266 3-058-753-01 RETAINER, HINGE 3-058-802-01 SPRING, B LOCK...

  • Page 129: Fdd Block Assembly

    6-1-7. FDD BLOCK ASSEMBLY (Note 2) CN201 (Note 2) The FD block assembly is a mechanical unit which has completely been adjusted in the factory. So never disassemble the FD block assembly. Ref. No. Part No. Description Remark Ref. No. Part No.

  • Page 130: Cabinet (Rear) Block Assembly

    6-1-8. CABINET (REAR) BLOCK ASSEMBLY LCD901 (Note 4) ND801 SP901 not supplied (Note 3) supplied (Note 3) supplied supplied : BT701 (BATTERY, LITHIUM SECONDARY) Board on the mount position. (See page 4-43.) (Note 3) The eject mechanism portion is a mechanical unit which has completely been adjusted in the factory.

  • Page 131: Electrical Parts List

    AE-25 CD-311 6-2. ELECTRICAL PARTS LIST NOTE: The components identified by • Due to standardization, replacements in the • Items marked “*” are not stocked since they mark 0 or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.
  • Page 132 CD-311 CF-83 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R112 1-216-296-11 SHORT R150 1-218-969-11 RES-CHIP 1/16W R151 1-218-969-11 RES-CHIP 1/16W R152 1-218-969-11 RES-CHIP 1/16W R153 1-218-969-11 RES-CHIP 1/16W R154 1-218-990-11 SHORT R155 1-218-985-11 RES-CHIP 470K 1/16W R156 1-218-965-11 RES-CHIP...
  • Page 133 FU-153 MA-404 PK-55 (TYPE C) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7074-794-A FU-153 BOARD, COMPLETE C305 1-125-837-91 CERAMIC CHIP 6.3V C306 1-107-820-11 CERAMIC CHIP 0.1uF ********************** (Ref.No.: 2,000 Series) C307 1-119-749-11 TANTAL. CHIP 33uF <...
  • Page 134 1-469-525-91 INDUCTOR 10uH L903 1-469-525-91 INDUCTOR 10uH < DIODE > L904 1-469-525-91 INDUCTOR 10uH D701 8-719-061-81 DIODE TLYU1002 (TPX1, SONY) L905 1-412-949-21 INDUCTOR 6.8uH D702 8-719-061-81 DIODE TLYU1002 (TPX1, SONY) D703 8-719-064-05 DIODE TLGU1002 (TPX1, SONY) < TRANSISTOR > D782...
  • Page 135 PK-55 (TYPE C) PK-55 (TYPE S) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R716 1-218-956-11 RES-CHIP 1.8K 1/16W R927 1-208-721-11 METAL CHIP 0.5% 1/16W R717 1-218-956-11 RES-CHIP 1.8K 1/16W R718 1-218-958-11 RES-CHIP 2.7K 1/16W R928 1-218-961-11 RES-CHIP 4.7K 1/16W...
  • Page 136 Part No. Description Remark Ref. No. Part No. Description Remark C711 1-164-870-11 CERAMIC CHIP 68PF D703 8-719-064-05 DIODE TLGU1002 (TPX1, SONY) C801 1-107-820-11 CERAMIC CHIP 0.1uF D782 8-719-075-15 DIODE MAZT082H08S0 D783 8-719-075-15 DIODE MAZT082H08S0 C802 1-107-820-11 CERAMIC CHIP 0.1uF C803 1-164-943-11 CERAMIC CHIP 0.01uF...
  • Page 137 PK-55 (TYPE S) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSISTOR > R867 1-216-055-00 METAL CHIP 1.8K 1/10W R868 1-216-055-00 METAL CHIP 1.8K 1/10W Q851 8-729-042-72 TRANSISTOR UN9214J- (K8).SO R869 1-218-977-11 RES-CHIP 100K 1/16W Q852 8-729-042-59 TRANSISTOR UN9112J- (K8).SO...
  • Page 138 PK-55 (TYPE S) VF-143 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark S709 1-771-331-81 SWITCH, PUSH (1 KEY) (MOVIE) C626 1-113-642-11 TANTAL. CHIP 47uF < SENSOR > C628 1-117-720-11 CERAMIC CHIP 4.7uF C629 1-164-505-11 CERAMIC CHIP 2.2uF 0 C630 SE701...
  • Page 139 VF-143 VP-55 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R507 1-218-969-11 RES-CHIP 1/16W A-7074-793-A VP-55 BOARD, COMPLETE R508 1-218-971-11 RES-CHIP 1/16W ********************* R510 1-218-990-11 SHORT (Ref.No.: 2,000 Series) R513 1-218-975-11 RES-CHIP 1/16W R514 1-218-971-11 RES-CHIP 1/16W <...
  • Page 140 VP-55 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark IC204 8-759-444-87 IC NJM324V (TE2) R232 1-208-943-11 METAL CHIP 220K 0.5% 1/16W IC205 8-759-058-45 IC NJM3403AV (TE2) R233 1-208-935-11 METAL CHIP 100K 0.5% 1/16W R234 1-208-935-11 METAL CHIP 100K 0.5% 1/16W...
  • Page 141 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-066-743-51 MANUAL, INSTRUCTION (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK) 3-066-743-61 MANUAL, INSTRUCTION (SWEDISH, RUSSIAN) (AEP) 3-066-743-71 MANUAL, INSTRUCTION (ARABIC) (E) 3-066-743-81 MANUAL, INSTRUCTION (KOREAN) (KR) 3-067-797-11 STRING (T), CAP 3-987-015-01 BELT (S), SHOULDER A-7094-140-A BATTERY PACK (NP-330) (US, CND) A-7094-141-B BATTERY PACK (NP-330)
  • Page 142 FOR CAMERA COLOR REPRODUCTION ADJUSTMENT Take a copy of CAMERA COLOR For NTSC mode REPRODUCTION FRAME with a clear sheet for use. MVC-FD97 For PAL mode MVC-FD97 – 169 –...
  • Page 143 MVC-FD97 2001F0500-1 Sony EMCS Co. Kohda TEC 9-929-887-32 © 2001. 6 – 170 – Published by PV Customer Center...

  • Page 144: Revision History

    Reverse 992988732.pdf Revision History S.M. Rev. Ver. Date History Contents issued 2001.03 Official Release — — 2001.06 Correction S.M. correction: Page 5-28...

Table of Contents