As An External Drive - Sony MVC-FD100 Service Manual

MVC-FD100/FD100H/FD200/FD200H
Notes
• You cannot copy uncompressed images.
• You cannot copy the image that is bigger
than 1.4 MB.
• You cannot copy the images that the total
amount of the images is bigger than
1.4 MB. If "NOT ENOUGH MEMORY"
appears or flashes on the INDEX
screen, cancel some images to copy and try
again.
• If you eject and insert the floppy disk or
the "Memory Stick" without selecting
[EXIT] after "COMPLETE" appears, the
image will be copied.
• The number of floppy disks that is needed
for copying is as a guide, which is
t
displayed when selecting [MS FD].
4
Select [ENTER].
The marks on the selected
images change from green to
white.
0 0 0 1 - 0 0 0 6 / 0 1 0 0
PRINT MARK ENTER CANCEL
SELECT OK
To unmark selected print
marks
Select the images to be unmarked in
step 3 with the control button, then
select [ENTER].
To unmark all the print
marks
Select [FILE], [PRINT MARK],
[ALL], and then [OFF] from the menu.
The marks on all images are
removed.
To print out using the FVP-1
Mavica Printer
Set PRESET SELECT SW to PC on
the printer.
Notes
• You cannot mark moving images, Clip
Motion images or images recorded in
TEXT mode.
• If you mark an image recorded in TIFF
mode with a print mark, only the
uncompressed image is printed, and the
JPEG image recorded at the same time is
not printed.
Copying all the
information on your
floppy disk (DISK
COPY)
You can copy to another disk not only
the images you have recorded with
your camera but also various files you
have created in other software with
your computer.
Notes
• Once you carry out DISK COPY, all
information saved on the recipient floppy
disk is erased to be replaced by newly
written data including the protected image
data. Check the contents of the recipient
disk before copying the disk.
• Be sure to use the floppy disk that has been
formatted by this camera to carry out
DISK COPY (page 81).
1, 4
3
1
2
1
Set the MS/FD selector to FD,
then insert the floppy disk to
be copied.
2 Select [FILE], [DISK TOOL],
[DISK COPY], and then [OK]
from the menu.
"DISK ACCESS" appears.
3
When "CHANGE FLOPPY
DISK" is displayed, eject the
floppy disk.
"INSERT FLOPPY DISK"
appears.
79
Format
When you format a floppy disk or a
"Memory Stick," all data stored on the
floppy disk or the "Memory Stick" will
be deleted. Check the contents of the
floppy disk or the "Memory Stick"
before formatting.
Note
Even if images are protected, these images
will be deleted.
1
2
3
1
Select the floppy disk or the
"Memory Stick" using the
MS/FD selector.
2
Insert only the floppy disk or
the "Memory Stick" you want
to format.
Be sure to insert only the media
you want to format.
3 Select [FILE] from the menu.
• When formatting a floppy disk
Select [DISK TOOL],
[FORMAT], and then [OK] from
the menu.
• When formatting a "Memory
Stick"
Select [FORMAT], and then
[OK] from the menu.
To cancel formatting
Select [CANCEL] in step 3.
81
4
Insert another floppy disk.
"RECORDING" appears. When
copying is completed,
"COMPLETE" appears.
To end copying, select [EXIT].
To continue copying to other
floppy disks
After "COMPLETE" appears in step 4,
select [CONTINUE] and repeat steps 3
and 4 above.
To cancel copying partway
Select [CANCEL].
Note
If you eject and insert the floppy disk
without selecting [EXIT] after
"COMPLETE" appears, DISK COPY will
be carried out onto the floppy disk.
80
Notes
• Format the floppy disk or the
"Memory Stick" only using this
camera. You cannot format the
floppy disk or the "Memory Stick"
using a computer via the USB cable.
• When you format, be sure to use a fully
charged battery pack or the AC power
adaptor as the power source.
B As an external drive
Using the camera as
an external drive of a
computer
Once you connect the camera to a
computer using the USB cable, you
can use the camera as a floppy disk/
"Memory Stick" drive of a computer.
Install the USB driver to the computer
beforehand (page 29).
For Windows 98, Windows
98SE, Windows 2000,
Windows Me and Windows
XP Users
1
Select the drive type using
the MS/FD selector on this
camera.
When used as the floppy disk
drive, set the MS/FD selector to
FD.
When used as the "Memory Stick"
drive, set the MS/FD selector to
MS.
2
Connect the AC power
adaptor and turn on the
camera.
3
Connect the camera to the
computer using the supplied
USB cable.
82
1-20
Selecting still images
to print (PRINT MARK)
You can mark a print mark on still
images recorded with your camera.
This mark is convenient when you
have images printed at a shop that
conforms with the DPOF (Digital Print
Order Format) standard.
1
2, 3, 4
In single mode
1
Set the PLAY/STILL/MOVIE
selector to PLAY and display
the image you want to print.
2
Select [FILE], [PRINT MARK],
and then [ON] from the menu.
The (print) mark is marked on
the displayed image.
To unmark the print mark
Select [OFF] in step 2.
In INDEX mode
1
Set the PLAY/STILL/MOVIE
selector to PLAY, then
display the INDEX screen.
2 Select [FILE], [PRINT MARK],
and then [SELECT] from the
menu.
3
Select the images to be
marked with the control
button.
4
Open "My Computer" on
Windows and check the icon
"Removable Disk," then use
the camera as an external
drive.
Note
• When using Windows 2000, Windows Me,
or Windows XP, see also page 31.
• The drive symbol ((D:), etc.) may differ
depending on your computer.
• If you are using Mac OS X(v10.0/v10.1),
you can use only a "Memory Stick" with a
computer running Mac OS X(v10.0/
v10.1). Even if you insert a floppy disk,
Mac OS X(v10.0/v10.1) cannot recognize
it. To use data saved on a floppy disk,
copy it to a "Memory Stick" first
(page 77).