Download Print this page

Advertisement

SERVICE MANUAL
Level 2
Ver 1.0 2000. 03
On the FC-72 board
This service manual provides the information that is premised the circuit board
replacement service and not intended repair inside the FC-72 board.
Therefore, schematic diagram, printed wiring board and electrical parts list of
the FC-72 board are not shown.
The following pages are not shown.
Block diagram ............................... Page 3-9 to 3-18
Schematic diagram ....................... Page 4-9 to 4-26
Printed wiring board ..................... Page 4-27 to 4-30
Electrical parts list ........................ Page 6-7 to 6-14
The above-described information is shown in service manual Level 3.
MVC-FD85/FD90
Photo: MVC-FD90
SPECIFICATIONS
US Model
Canadian Model
AEP Model
UK Model
Australian Model
Hong Kong Model
Chinese Model
Tourist Model
Japanese Model
MVC-FD85/FD90
Korea Model
Brazilian Model
This service manual contains information
for japanese model as well.
DIGITAL STILL CAMERA
E Model
MVC-FD90
MVC-FD85

Advertisement

   Summary of Contents for Sony MVC-FD85

  • Page 1

    MVC-FD85/FD90 SERVICE MANUAL US Model Canadian Model AEP Model Level 2 UK Model E Model Australian Model Hong Kong Model Ver 1.0 2000. 03 Chinese Model Tourist Model Japanese Model MVC-FD85/FD90 Korea Model MVC-FD90 Brazilian Model Photo: MVC-FD90 MVC-FD85 This service manual contains information On the FC-72 board for japanese model as well.

  • Page 2

    MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

  • Page 3: Table Of Contents

    Order of Adjustments ······················································ 5-7 2-10. FOCUS MOTOR UNIT, Subjects ··········································································· 5-7 ZOOM MOTOR UNIT (MVC-FD85) ···························· 2-7 1-2. INITIALIZATION OF B, D, E, F, 7 PAGE DATA ········· 5-8 2-11. CIRCUIT BOARDS LOCATION ··································· 2-8 1-2-1. INITIALIZATION OF D PAGE DATA ·························· 5-8 2-12.

  • Page 4

    V-COM Adjustment (PK-50 board) ······························ 5-31 White Balance Adjustment (PK-50 board) ···················· 5-32 1-5-3. LCD SYSTEM ADJUSTMENT (PK-52 board) (MVC-FD85) ································································· 5-32 LCD Initial Data Input ·················································· 5-32 VCO Adjustment (PK-52 board) ··································· 5-33 Black Limit Adjustment (PK-52 board) ························ 5-33 Bright Adjustment (PK-52 board) ·································...

  • Page 5: Service Note

    The electric shock is caused by the charged voltage which is kept without discharging when the main power of the MVC-FD85/FD90 is simply turned off. Therefore, the remaining voltage must be discharged as described below.

  • Page 6: Self-diagnosis Display

    [Description on Self-diagnosis Display] Self-diagnosis display • C: ss: ss The contents which can be handled by customer, are displayed. • E: ss: ss The contents which can be handled by engineer, are displayed. Display Code Countermeasure Cause Caution Display During Error Change the disk and turn off the main C:32:01 Defective floppy disk.

  • Page 7

    MVC-FD85/FD90 SECTION 1 This section is extracted from GENERAL instruction manual.

  • Page 16

    1-10...

  • Page 17

    1-11...

  • Page 18

    1-12...

  • Page 19

    1-13...

  • Page 20

    1-14...

  • Page 21

    1-15E...

  • Page 22: Disassembly

    MVC-FD85/FD90 SECTION 2 DISASSEMBLY The following flow chart shows the disassembly procedure. 2-1 . Cabinet (Rear) block assembly LCD, PK-50/52 board 2-4. LCD, PK-50/52 board chack service position 2-8. Eject button section 2-2. FC-72 board, Floppy disk drive 2-6. DC-IN connector, Microphone UNIT Control switch block (MF 330)(MVC-FD90) 2-7.

  • Page 23: Board, Floppy Disk Drive

    Flash unit (10p) qa Cabinet (front) qf Blind sheet block assembly qg Floppy disk drive (4 × ) 2 Flexible board (18P) MVC-FD85 FP-231 MVC-FD90 FP-167 6 Claw qd FC Bracket 3 Lens block assembly MVC-FD85 (26P) qs Three screws (M2 ×...

  • Page 24: Lens Block Assembly

    [ MAIN (FC-72) BOARD, LENS BLOCK (CD-246/248 BOARD) CHECK SERVICE POSITION ] FU-52 harness (9p) CPC-12 jig FU-51 harness (12p) (J-6082-436-A) AC IN FC-72 board AC POWER ADAPTOR PK-52 board (MVC-FD85) PK-50 board (MVC-FD90) CD-248 board Lens block assembly (MVC-FD85) CD-246 board MVC-FD90 FC-72 board...

  • Page 25: Lcd, Pk-50/52 Board

    (24p) 5 PK shield case (lower) assembly 8 Tapping screw (M2 × 5) 4 Tapping screw (M2 × 5) PK-52 board (MVC-FD85) PK-50 board (MVC-FD90) PRECAUTION DURING INSTALLATION Set this knob the center. Note : Refer to page 5-27 for LCD type check.

  • Page 26: Flash Unit, Fu-140/146 Board

    2-5. FLASH UNIT, FU-140/146 BOARD 2 Two tapping screws (M2 × 5) 1 ST inslating sheet 6 FU-140 board (MVC-FD90) FU-146 board (MVC-FD85) 5 Two tapping screws (M2 × 5) 4 Control switch block (6p) 3 Flash unit Short jig (see page 5) 1k Ω...

  • Page 27: Dc-in Connector, Microphone Unit

    2-6. DC-IN CONNECTOR, MICROPHONE UNIT (PRECAUTION DURING INSTALLATION) Align the switch position as shown. Control switch block (MF 330) Focus slider REMOVING THE MICROPHONE UNIT 2 DC retainer 2 Microphone cover 1 Two tapping screws (M2 × 5) 4 Microphone cushion 3 Microphone holder 3 DC-IN connector...

  • Page 28: Eject Button Section

    Gear cover Rack (A) 2-9. FOCUS STEPPING MOTOR, 2-10.FOCUS MOTOR UNIT, ZOOM STEPPING MOTOR, ZOOM MOTOR UNIT ND-METER (MVC-FD85) (MVC-FD90) 3 Lens sheet (L) 1 Two screws (M2 × 5) 1 Two screws (M2 × 5) 2 Lens frame 4 screw...

  • Page 29: Circuit Boards Location

    2-11.CIRCUIT BOARDS LOCATION PK-50 (MVC-FD90) CD-246 (MVC-FD90) CD-248 (MVC-FD85) FU-140 (MVC-FD90) PK-52 (MVC-FD85) FU-146 (MVC-FD85) FLASH UNIT FC-72 2-12.FLEXIBLE BOARDS LOCATION CONTROL SWITCH BLOCK (From FLOPPY DISK DRIVE) (From ND901) (From LCD901) (From FLOPPY DISK DRIVE) CONTROL SWITCH BLOCK (MF300)

  • Page 30: Block Diagrams

    MVC-FD85/FD90 SECTION 3 BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. Note:FD85 model:MVC-FD85 FD90 model:MVC-FD90 CD-248/246 BOARD FC-72 BOARD Note:FD85 model/FD90 model (4-13)

  • Page 31: Overall Block Diagram (2/2)

    MVC-FD85/FD90 3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. FLOPPY FC-72 BOARD Note:FD85 model:MVC-FD85 FD90 model:MVC-FD90 DISK DRIVE UNIT (4-18) (4-17) WRITE DATA R/W A,B...

  • Page 32: Power Block Diagram (1/2)

    6.5V REG A 4.9V Q018 CN003 CN002 IC001 el 3.2V Q023 CAM P 5V IC001 r; EMERGENCY FDD P 5V DETECT Q013,016 L017 4.9V PANEL 4.9V 800mVp-p 800mVp-p Note:FD85 model:MVC-FD85 2.0µsec 2.0µsec FD90 model:MVC-FD90 LCD DD ON SYS DD ON...

  • Page 33: Power Block Diagram (2/2)

    IC505 IC506 CAM 15V CAM 15V MEMORY CONTROL CAM 3.3V VIDEO ENCODER IMAGER CN101 CN201 OPD,OSD,HOST IF FD85 MODEL : MVC-FD85 /101 RES CONTROL Note: SG,JPEG,L-MODE 64 Mbit FLASH ROM SDRAM FD90 MODEL : MVC-FD90 FD85 modelL/FD90 model SDRAM 16Mbit...

  • Page 34: Printed Wiring Boards And Schematic Diagrams

    (FD90 MODEL) FD85 MODEL FD90 MODEL CN201 CN101 LENS UNIT IMAGER FD85 MODEL : MVC-FD85 FD90 MODEL : MVC-FD90 FLASH -LCD type check- UNIT By measurimg the resistor valve between 13 of CN803(FC-72 board) and Pin of CN803(FC-72 board),the type of LCD can...

  • Page 35: Schematic Diagrams

    1. Connection Pattern box (For schematic diagrams) • All capacitors are in µF unless otherwise noted. pF : µµF. Approx. 97 cm (MVC-FD85) 50V or less are not indicated except for electrolytics and 1.5 m (MVC-FD90) tantalums. • Chip resistors are 1/10W unless otherwise noted.

  • Page 36: Schematic Diagram

    0.1u 3300 PK-50 (MVC-FD90) in the diagram. CD-246 (MVC-FD90) PK-52 (MVC-FD85) • Chip parts C110 Transistor R109 Precautions Upon Replacing CCD Imager • The CD-246 board mounted as a repair part is not equipped...

  • Page 37: Ccd Imager)(fd85 Model)

    • Refer to page 4-59 for parts location. • This board is four-layer print board. However, the pat- C210 terns of layers two and three have not been included CD-248 (MVC-FD85) R209 in the diagram. FU-140 (MVC-FD90) • Chip parts...

  • Page 38: Pages From 4-9 To 4-30 Are Not Shown

    MVC-FD85/FD90 Schematic diagram and printed wiring board of the FC-72 board are not shown. Pages from 4-9 to 4-30 are not shown.

  • Page 39: Av Out/key In, Back Light, Rgb, Tg)(fd90 Model) Printed Wiring Board

    • Chip parts Transistor Diode There are few cases that the part printed on this diagram isn’t mounted in this model. PK-50 (MVC-FD90) CD-246 (MVC-FD90) PK-52 (MVC-FD85) FC-72 AV OUT/KEY IN, BACK LIGHT, RGB, TG 4-31 4-32 PK-50...

  • Page 40

    MVC-FD85/FD90 AV OUT/KEY IN, BACK LIGHT, RGB, TG 4-33 4-34 PK-50...

  • Page 41: Av Out/key In, Back Light, Rgb, Tg)(fd85 Model) Printed Wiring Board

    • Chip parts Transistor Diode There are few cases that the part printed on this diagram isn’t mounted in this model. PK-50 (MVC-FD90) CD-246 (MVC-FD90) PK-52 (MVC-FD85) FC-72 AV OUT/KEY IN, BACK LIGHT, RGB, TG 4-35 4-36 PK-52...

  • Page 42

    MVC-FD85/FD90 AV OUT/KEY IN, BACK LIGHT, RGB, TG 4-37 4-38 PK-52...

  • Page 43: Schematic Diagram

    • Refer to page 4-31, 35 for printed wiring board. (FD90 MODEL) NO MARK:REC/PB MODE PK-50 BOARD(1/4) R :REC MODE SIGNAL PATH PK-52 BOARD(1/3) (FD85 MODEL) P :PB MODE FD85 MODEL:MVC-FD85 FD90 MODEL:MVC-FD90 VIDEO SIGNAL REC/PB AMP(REF BLOCK) AUDIO -REF.NO.:10000 SERIES- CHROMA Y/CHROMA SIGNAL...

  • Page 44: Pk-50/52 (back Light)(2/4)

    TO(3/3) FD85 MODEL Note : Note : The components identified by Les composants identifiés par FD85 MODEL:MVC-FD85 mark 0 or dotted line with mark une marque 0 sont critiques FD90 MODEL:MVC-FD90 0 are critical for safety. pour la sécurité. Replace only with part number Ne les remplacer que par une specified.

  • Page 45: Rgb Driver/tg

    MVC-FD85/FD90 For schematic diagram • Refer to page 4-35 for printed wiring board. • Refer to page 4-56 for waveforms. PK-52 BOARD(3/3) (FD85 MODEL) RGB DRIVER/TG(RGB/TG BLOCK) -LCD type check- R912 By measurimg the resistor valve between -REF.NO.:6000 SERIES- IC903...

  • Page 46: Rgb Driver

    MVC-FD85/FD90 For schematic diagram • Refer to page 4-31 for printed wiring board. • Refer to page 4-56 for waveforms. PK-50 BOARD(3/4) Note:Refer to page 4-48for (FD90 MODEL) NO MARK:REC/PB MODE (Note) LCD type check. R :REC MODE R817 RGB DRIVER(RGB BLOCK) 5.6k:Type CA...

  • Page 47: Schematic Diagram

    MVC-FD85/FD90 For schematic diagram • Refer to page 4-31 for printed wiring board. • Refer to page 4-55 for waveforms. PK-50 BOARD(4/4) NO MARK:REC/PB MODE (FD90 MODEL) -LCD type check- R :REC MODE TG(TG BLOCK) P :PB MODE By measurimg the resistor valve between of CN803(FC-72 board) and Pin -REF.NO.:5000 SERIES-...

  • Page 48: Schematic Diagram

    FB003 TERMINAL DC_PACK_SW UNREG3(TRANS 4.9V) (SEE PAGE 4-25) F002 1.4A/32V R021 UNREG3 R006 UNREG2 (FDD_P_5V) F001 1.4A/32V FD85 MODEL:MVC-FD85 UNREG2 (FLASH) FD90 MODEL:MVC-FD90 Q004 UNREG1 (3.2/1.8/HI) SSM3K03FE(TPL3) F005 1.4A/32V Q005 SSM3K03FE(TPL3) Note : Note : The components identified by Les composants identifiés par...

  • Page 49: Dc In)(fd90 Model)

    For printed wiring boards • Refer to page 4-61 for parts location. • This board is four-layer print board. However, the pat- terns of layers two and three have not been included CD-248 (MVC-FD85) in the diagram. FU-140 (MVC-FD90) • Chip parts...

  • Page 50: Dc In)(fd85 Model)

    For printed wiring boards • Refer to page 4-61 for parts location. • This board is four-layer print board. However, the pat- terns of layers two and three have not been included CD-248 (MVC-FD85) in the diagram. FU-140 (MVC-FD90) • Chip parts...

  • Page 51: Waveform

    MVC-FD85/FD90 4-3. WAVEFORM CD-246 CD-248 PK-50/52 BOARD BOARD BOARD (MVC-FD90 model) (MVC-FD85 model) (MVC-FD90/FD85 model) REC/PB REC/PB REC/PB IC101 1,3 IC201 1,3 IC901 8 IC904 wk IC802 wf 6.5µsec 6.5µsec 8.7Vp-p 8.7Vp-p 127µsec 127µsec 3.8Vp-p 4.4Vp-p 440mVp-p 85nsec IC101 2...

  • Page 52: Parts Location

    4-4. PARTS LOCATION Waveforms and parts location of the FC- 72 board are not shown. Pages from 4-57 to 4-58 are not shown. CD-246 BOARD (SIDE A) D101 IC101 R111 R112 CD-246 BOARD (SIDE B) C101 C102 C103 C104 C105 C106 C107 C108...

  • Page 53

    PK-50 BOARD (SIDE A) PK-50 BOARD (SIDE B) PK-52 BOARD (SIDE A) PK-52 BOARD (SIDE B) BT701 R817 C709 R703 B-14 BT701 R728 C705 B-14 R729 R818 C711 C-14 R704 C-15 R782 C709 R787 A-14 C701 R851 C783 A-14 R705 B-14 C701 R851...

  • Page 54

    FU-140 BOARD (SIDE A) FU-146 BOARD (SIDE A) D002 D002 D003 D003 D004 D004 D006 D006 FB002 FB002 FB003 FB003 Q002 Q002 Q003 Q003 Q005 Q005 R004 R004 R005 R005 R008 R008 R009 R009 R019 R019 R020 R020 R021 R021 FU-140 BOARD (SIDE B) FU-146 BOARD (SIDE B) C001...

  • Page 55: Adjustments

    MVC-FD85/FD90 SECTION 5 ADJUSTMENTS Before Starting Adjustment EVR Data Re-writing Procedure When Replacing Board The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.

  • Page 56: Adjusting Items When Replacing

    *3: When replacing the FDD unit, reset the data of page: D, address: 6C to 6F to “00”. (Refer to “Record of Use check” of “5-2. SERVICE MODE”) *4: When replacing the Flash unit, reset the data of page: D, address: 67 to “00”. (Refer to “Emergency Memory Address of Flash Unit” of “5-2. SERVICE MODE”) *5: CD-248 board IC201: MVC-FD85, CD-246 baord IC101: MVC-FD90...

  • Page 57: Adjustment

    5-1. ADJUSTMENT 1-1. PREPARATIONS BEFORE ADJUSTMENT 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope • AC power adapter • Regulated power supply • Digital voltmeter • Frequency counter Ref. No. Name Parts Code Usage Auto white balance adjustment/check Filter for color temperature correction (C14) J-6080-058-A White balance adjustment/check...

  • Page 58: Preparations

    1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Pattern box Note 2: When performing only the adjustments, the lens block and boards need not be disassembled. 1) Connect the equipment for adjustments according to Fig. 5-1- 2) Connect the adjustment remote commander to the following connector or jack.

  • Page 59: Discharging Of The Flashlight Power Supply

    1-1-3. Discharging of the Flashlight Power Supply The capacitor which is used as power supply of flashlight is charged with 200 V to 300 V voltage. Discharge this voltage before starting adjustments in order to protect service engineers from electric shock during adjustment.

  • Page 60

    AC power adaptor Adjustment remote CD-248 board : MVC-FD85 model CN101: MVC-FD90 model commander CD-246 board : MVC-FD90 model CN201: MVC-FD85 model CN001 CN002 FDD UNIT CN251 CN301 CD-248/246 CN701 board CN101/CN201 CN702 FC-72 board CPC-12 jig CN703 (J-6082-436-A) CN101...

  • Page 61: Precaution

    MACRO (PK-50 board) (MVC-FD90) ......OFF FOCUS (MF unit) (MVC-FD90) ......MANUAL FLASH LEVEL (CAMERA menu) ....... NORMAL EXPOSURE (CAMERA menu) ........0EV (PK-52 board) (MVC-FD85) ......AUTO P. EFFECT (EFFECT menu) ........... OFF (No mark indicated on LCD) 10. DISPLAY (PK-52/50 board) ..........OFF 2.

  • Page 62: Initialization Of B, D, E, F, 7 Page Data

    2) Select page: 2, address: 03, and set the following data. 1F to 61 Fixed data-1 (Initialized data) 05: MVC-FD85 62 to 63 Fixed data-2 (Modified data. Copy 04: MVC-FD90 the data built in the same model.) 3) Select page: 2, address: 00, and set data: 2D.

  • Page 63: Modification Of B, E, F, 7 Page Data

    *2: LCD TYPE SA/ LCD TYPE ST Select page: 6, address: 03, and set the following data. 90/80 7A/6A *3: LCD TYPE SH/ LCD TYPE CA 05: MVC-FD85 (*2) (*3) 04: MVC-FD90 Select page: 6, address: 00, and set data: 2D.

  • Page 64

    3. F Page table Note: Fixed data-1: Address Initial value Remark Initialized data.(Refer to “1. Initializing the B, E, F, 7 Page Data”). FD85 FD90 Fixed data-2: Color reproduction adj. Modified data. (Refer to “2. Modification of B, E, F, 7 Page Data”). (ND Filter OFF) Address Initial value...

  • Page 65: F Page Table

    4. 7 Page Table Note: Address Initial value Remark Fixed data-1: FD85 FD90 Initialized data. (Refer to “1. Initializing the B, E, F, 7 Page Data”.) Mechanical shutter adj. Fixed data-2: Modified data. (Refer to “2. Modification of B, E, F, 7 Page Data”). Address Initial value Remark...

  • Page 66: B Page Table

    5. E Page Table Note: Address Initial value Remark Fixed data-1: NTSC Initialized data. (Refer to “1. Initializing the B, E, F, 7 Page Data”.) CCD white defect compensation Fixed data-2: Modified data. (Refer to “2. Modification of B, E, F, 7 Page Data”). Address Remark 00 to FF...

  • Page 67: Video System Adjustments

    1-3. VIDEO SYSTEM ADJUSTMENTS 1. Video Output Level Adjustment (FC-72 board) Adjust the sync level and burst level of the composite video signal output. Mode PLAY Signal Arbitrary Measurement Point Video terminal of AV OUT jack (75 Ω terminated) Measuring Instrument Oscilloscope Adjustment Page Adjustment Address...

  • Page 68: Camera System Adjustments

    1-4. CAMERA SYSTEM ADJUSTMENTS Before perform the camera system adjustments, check that the specified values of “VIDEO SYSTEM ADJUSTMENT” are satisfied. Data setting during camera system adjustments: 2. HALL Adjustment For detecting the position of the lens iris, adjust the hall AMP gain Perform the following data setting before the camera system and offset.

  • Page 69: Flange Back Adjustment (using Minipattern Box)

    Specified voltage: The specified voltage varies according to the minipattern box, so adjust the power supply output voltage to the specified voltage written Note: MVC-FD85/MVC-FD90 on the sheet which is supplied with the minipattern box. Select page: 6, address: 01, set data: 13, and press the PAUSE button of the adjustment remote commander.

  • Page 70: (using Flange Back Adjustment Chart)

    7) Select page: 6, address: 02, and check that the data is “01”. Processing after Completing Adjustments: Note: MVC-FD85/MVC-FD90 1) Select page: 0, address: 01, and set data: 00. 4) Select page: 6, address: 01, set data: 13, and press the PAUSE 2) Turn off the power and turn on again.

  • Page 71: Flange Back Check

    1) FOCUS ............ AUTO (MVC-FD90) 01, set data: 00, and press the PAUSE button..AUTO (No mark indicated on LCD) (MVC-FD85) Note: 2 Install the clear chart at a distance of about 10 cm from the front of the lens. (It is recommended.) Checking method: Place the Siemens star 2.0m from the front of the lens.

  • Page 72: Picture Frame Setting

    8. Picture Frame Setting Check on an oscilloscope Mode STILL Subject Color bar chart 1. Horizontal period (Color reproduction adjustment frame) About 90 cm from the front of the lens Measurement Point Video output terminal Measuring Instrument Oscilloscope and TV monitor Specified Value A=B, C=D, E=F Note 1: Display data of page 1 of the adjustment remote commander.

  • Page 73: Light Level Adjustment And Nd Shutter Check

    9. Light Level Adjustment and ND Shutter Check 10. Mixed Color Cancel Adjustment Adjust the standard LV value. Perform the mixed color cancel adjustment using the each data of the color bars. Mode STILL Mode STILL Subject Clear chart (Color bar standard picture frame) Subject Color bar chart (Color bar standard picture frame)

  • Page 74: Auto White Balance Standard Data Input

    11. Auto White Balance Standard Data Input 12. White Balance ND Filter Compensation Adjust the white balance standard data at 3200 K. (MVC-FD90) Compensate the white balance deviation when ND filter is ON. Mode STILL Mode STILL Subject Clear chart (Color bar standard picture frame) Subject Clear chart...

  • Page 75: Mvc-fd90

    01, set data: 00, and press the PAUSE button. Note 3: After the power is turned on, this adjustment can be done only Specified Value R ratio: 29E0 to 2B20 (MVC-FD85) once. B ratio: 5F20 to 6060 (MVC-FD85) R ratio: 2760 to 28A0 (MVC-FD90)

  • Page 76

    15. Color Reproduction Adjustment (ND Filter ON) (MVC-FD90) Adjust the color Separation matrix coefficient so that proper color reproduction is produced. Mode STILL Subject Color bar chart (Color bar standard picture frame) Adjustment Page Adjustment Address 51 to 58, 60 to 63 Note 1: This adjustment should be carried out upon completion of “Auto White Balance Standard Data Input”, “Auto White Balance Adjustment”...

  • Page 77

    16. Color Reproduction Check Mode STILL Subject Color bar chart (Color reproduction adjustment frame) Measurement Point Video output terminal Measuring Instrument NTSC vectorscope (NTSC mode) PAL vectorscope (PAL mode) Specified Value Each center of all color luminance points should settle within each color reproduction frame.

  • Page 78: Data Check

    14) Select page: 1, and check that the display data (Note2) satisfies the B ratio specified value. 15) Only for MVC-FD85 model, proceed to step 24). • INDOOR (ND filter ON) data check (MVC-FD90) 16) Select page: F, address: 27, after noting down the data, set data: 80, and press the PAUSE button.

  • Page 79

    F : XX : 64 Select page: 6, address: 93, and set the following data. Y level data 80 : MVC-FD85 Note 5: Display data of page 1 of the adjustment remote commander. 60 : MVC-FD90 1 : XX : XX Select page: 6, address: 6C, and set data: 01.

  • Page 80: Ccd White Defect Compensation

    20. CCD Black Defect Compensation 21. CCD White Defect Compensation Mode STILL Mode STILL Subject Clear chart Subject Clear chart (25 cm from the front of the lens) (25 cm from the front of the lens) (Note 1) (Note 1) Adjustment Page Adjustment Page Adjustment Address...

  • Page 81

    1-5. LCD SYSTEM ADJUSTMENT Before perform the LCD system adjustments, check that the specified 1-5-1. LCD Type Check values of “VIDEO SYSTEM ADJUSTMENT” are satisfied. By measuring the resistor value between Pin qd of CN803 and Pin Note 1: The back light (fluorescent tube) is driven by a high voltage AC 4 of CN803, the type of LCD can be discriminated.

  • Page 82: (mvc-fd90)

    1-5-2. LCD SYSTEM ADJUSTMENT (PK-50 board) (MVC-FD90) 1. LCD Initial Data Input 2. VCO Adjustment (PK-50 board) Set the VCO free-run frequency. If deviated, the LCD screen will Mode PLAY be blurred. Signal Arbitrary Mode PLAY Adjustment Page Signal Arbitrary Adjustment Address D0 to D9, DC to DF Measurement Point...

  • Page 83: D Range Adjustment (pk-50 Board)

    3. D Range Adjustment (PK-50 board) 4. Bright Adjustment (PK-50 board) Set the D range of the LCD driver to the specified value. If deviated, Set the level of the VIDEO signal for driving the LCD to the specified the LCD screen will become blackish or saturated (whitish). value.

  • Page 84: Contrast Adjustment (pk-50 Board)

    5. Contrast Adjustment (PK-50 board) 6. Color Adjustment (PK-50 board) Set the level of the VIDEO signal for driving the LCD to the specified Set the color saturation to the standard value. If deviated, the color value. If deviated, the screen image will be blackish or saturated will be too dark or light.

  • Page 85: V-com Level Adjustment (pk-50 Board)

    7. V-COM Level Adjustment (PK-50 board) 8. V-COM Adjustment (PK-50 board) Set the common electrode drive signal level of LCD to the specified Set the DC bias of the common electrode drive signal of LCD to the value. specified value. If deviated, the LCD display will move, producing flicker and Mode PLAY...

  • Page 86: White Balance Adjustment (pk-50 Board)

    9. White Balance Adjustment (PK-50 board) 1-5-3. LCD SYSTEM ADJUSTMENT (PK-52 board) Correct the white balance. (MVC-FD85) If deviated, the LCD screen color cannot be reproduced. 1. LCD Initial Data Input Mode PLAY Mode PLAY Signal Arbitrary Signal Arbitrary Measurement Point...

  • Page 87: Vco Adjustment (pk-52 Board)

    2. VCO Adjustment (PK-52 board) 3. Black Limit Adjustment (PK-52 board) Set the VCO free-run frequency. If deviated, the LCD screen will Set the amplitude of the VIDEO signal for driving the LCD to the be blurred. specified value. If deviated, the screen image will be blackish or saturated (whitish).

  • Page 88: Bright Adjustment (pk-52 Board)

    4. Bright Adjustment (PK-52 board) 5. Contrast Adjustment (PK-52 board) Set the level of the VIDEO signal for driving the LCD to the specified Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated value.

  • Page 89: Color Adjustment (pk-52 Board)

    6. Color Adjustment (PK-52 board) 7. VG Center Adjustment (PK-52 board) Set the color saturation to the standard value. If deviated, the color Set the video signal center level of LCD panel to an appropriate will be too dark or light. level.

  • Page 90: V-com Adjustment (pk-52 Board)

    8. V-COM Adjustment (PK-52 board) 9. White Balance Adjustment (PK-52 board) Set the DC bias of the common electrode drive signal of LCD to the Correct the white balance. specified value. If deviated, the LCD screen color cannot be reproduced. If deviated, the LCD display will move, producing flicker and Mode PLAY...

  • Page 91: System Control System Adjustment

    Cover the lens with a black cap. Lens block Power coda (J-6082-223-A) Flexible of MF unit (MVC-FD90 model only) Need not to be connected. FDD unit FU-146 board : MVC-FD85 model FU-146/140 board CN002 FU-140 board : MVC-FD90 model Fig. 5-1-28. 5-37...

  • Page 92: Alignment Check (fdd Unit)

    2. Alignment Check (FDD UNIT) Confirm that the FDD alignment is within the specifications. If deviated, reading and writing data from and to the floppy disk become impossible. Or compatibility of the floppy disk with other machines can be lost. Mode Playback Signal...

  • Page 93: Service Mode

    5-2. SERVICE MODE 2-1. ADJUSTMENT REMOTE COMMANDER The adjustment remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The adjustment remote commander performs bi-directional communication with the unit using the remote commander signal line (LANC). The resultant data of this bi-directional communication is written in the non-volatile memory.

  • Page 94: Data Process

    2-2. DATA PROCESS The calculation of the DDS display and the adjustment remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data.

  • Page 95: Service Mode

    2-3. SERVICE MODE 1. Setting the Test Mode 3. Emergency Memory Address of Flash Unit Page D Address 10 Page D Address 67 Data Function Data Function Normal No error Forced STILL mode power ON Flash unit emergency Forced PLAY mode power ON Forced MOVIE mode power ON Using method: When emergency occurs in the flash unit, the data...

  • Page 96: Record Of Use Check

    4. Record of Use check Page D Address 6C to 6F Address Function Remarks Recording counter Counter data 1 (Hexadecimal) Counter data 2 Counter data 3 Recording counter (Hexadecimal) / Counter data 4 Note: When this data is “80” to “FF”, the MC CAM (FC-72 board IC501) is abnormal. MC CAM emergency Note: When replacing the floppy disk drive unit, initialize these data.

  • Page 97: Switch Check (1)

    DISK IN SW (FDD unit) XSTILL/MOVIE SW MOVIE STILL or PLAY (PK-52/50 board S710) Note: PK-52 board: MVC-FD85 PK-50 board: MVC-FD90 Using method: Select page: 2, address: 43. By discriminating the bit value of display data, the state of the switches can be discriminated.

  • Page 98: Exploded Views

    Items marked “*” are not stocked since they • Abbreviation Replace only with part number specified. are seldom required for routine service. Some FD85: MVC-FD85 Les composants identifiés par une marque delay should be anticipated when ordering these FD90: MVC-FD90 0 sont critiques pour la sécurité.

  • Page 99

    6-1-2. CABINET (FRONT) BLOCK SECTION-2 (MVC-FD90) J901 (MVC-FD85) supplied not supplied not supplied supplied (MVC-FD90) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-3950-245-1 CABINET (FRONT) ASSY (FD90) X-3949-747-1 LABEL ASSY, LENS (FD90) X-3950-606-1 CABINET (FRONT) ASSY (FD85)

  • Page 100

    6-1-3. CABINET (REAR) BLOCK SECTION Note 1: LCD type check By measuring the resistor value between of CN803 (FC-72 board) and Pin not supplied CN803 (FC-72 board), the type of LCD can be discriminated. Type SA : 10 k Ω Type ST : 22 k Ω...

  • Page 101

    M903 supplied supplied M902 IC201 supplied M905 supplied M904 supplied (MVC-FD85) Be sure to read “Precautions Upon Replacing CCD Imager” on page 4-6,8 when changing the CCD imager. Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks...

  • Page 102: Electrical Parts List

    • Items marked “*” are not stocked since they • Abbreviation are seldom required for routine service. FD85 : MVC-FD85 Type SH: 4.7 kΩ Some delay should be anticipated when FD90 : MVC-FD90 ordering these items. CND : Canadian model.

  • Page 103

    CD-248 FC-72 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R206 1-216-831-11 METAL CHIP 6.8K 1/16W R207 1-216-857-11 METAL CHIP 1/16W R208 1-216-827-11 METAL CHIP 3.3K 1/16W R209 1-216-864-11 METAL CHIP 1/16W R210 1-216-805-11 METAL CHIP 1/16W R212 1-216-296-91 SHORT...

  • Page 104

    PK-50 (FD90) FU-140 FU-146 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-7074-298-A FU-140BOARD, COMPLETE (FD90) A-7074-300-A PK-50(CASI) BOARD, COMPLETE (FD90)(CA) ********************** *************************** A-7074-417-A FU-146BOARD, COMPLETE (FD85) A-7074-301-A PK-50(SHAP) BOARD, COMPLETE (FD90)(SH) ********************** *************************** (REF.NO.;4000 Series) (REF.NO.;5000 Series) <...

  • Page 105

    1-691-388-11 CONNECTOR, FFC/FPC 24P L851 1-414-753-91 INDUCTOR 4.7uH L852 1-424-674-11 INDUCTOR 22uH < DIODE > L853 1-419-387-21 INDUCTOR 100uH D701 8-719-061-81 DIODE TLYU1002(TPX1,SONY) L901 1-414-754-11 INDUCTOR 10uH D702 8-719-061-81 DIODE TLYU1002(TPX1,SONY) L902 1-414-754-11 INDUCTOR 10uH D703 8-719-064-05 DIODE TLGU1002(TPX1,SONY) L903...

  • Page 106

    PK-50 (FD90) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R720 1-216-829-11 METAL CHIP 4.7K 1/16W R913 1-216-844-11 METAL CHIP 1/16W R721 1-216-829-11 METAL CHIP 4.7K 1/16W (CA) R722 1-216-831-11 METAL CHIP 6.8K 1/16W R913 1-216-845-11 METAL CHIP 100K 1/16W R723...

  • Page 107

    PK-50 (FD90) PK-52 (FD85) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R951 1-216-864-11 METAL CHIP 1/16W < SENSOR > (CA) R952 1-216-864-11 METAL CHIP 1/16W SE701 1-801-868-41 SENSOR, SHOCK (SH) R953 1-216-864-11 METAL CHIP 1/16W <...

  • Page 108

    1-691-388-11 CONNECTOR, FFC/FPC 24P Q861 8-729-042-59 TRANSISTOR UN9112J-(K8).SO < DIODE > Q901 8-729-037-74 TRANSISTOR UN9213J-(K8).SO (SA) Q902 8-729-046-75 TRANSISTOR SI2301DS-T1 (SA) D701 8-719-061-81 DIODE TLYU1002(TPX1,SONY) Q903 8-729-427-74 TRANSISTOR XP4601-TXE D702 8-719-061-81 DIODE TLYU1002(TPX1,SONY) Q904 8-729-427-74 TRANSISTOR XP4601-TXE D703 8-719-064-05 DIODE TLGU1002(TPX1,SONY) D785 8-719-073-01 DIODE MA111-(K8).S0...

  • Page 109

    PK-52 (FD85) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R863 1-216-823-11 METAL CHIP 1.5K 1/16W R939 1-216-849-11 METAL CHIP 220K 1/16W R864 1-216-841-11 METAL CHIP 1/16W R940 1-216-837-11 METAL CHIP 1/16W R865 1-216-829-11 METAL CHIP 4.7K 1/16W R942...

  • Page 110

    PK-52 (FD85) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R981 1-216-864-11 METAL CHIP 1/16W M903 3-709-499-01 METER, ND (FD90) (SA) M904 3-709-573-01 MOTOR UNIT, FOCUS (FD85) R982 1-216-864-11 METAL CHIP 1/16W M905 3-709-574-01 MOTOR UNIT, ZOOM (FD85) R984 1-218-887-11 METAL CHIP 0.5%...

  • Page 111

    〈 〉 FOR CAMERA COLOR REPRODUCTION ADJUSTMENT Take a copy of CAMERA COLOR REPRODUCTION FRAME with a clear sheet for use. — 137 —...

  • Page 112

    MVC-FD85/FD90 Sony Corporation 2000C1649-1 Personal VIDEO Products Company 9-929-813-31 Printed in Japan © 2000.3 — 138 — Published by Safety & Service Engineering Dept.

This manual also for:

Mvc-fd90

Comments to this Manuals

Symbols: 0
Latest comments: