Related Manuals for Contura C 460
Summary of Contents for Contura C 460
- Page 1 Installation Installation instruction Installationsanleitung Monteringsvejledning instruction Installasjonsanvisning Asennusohje C 460 www.contura.eu...
- Page 2 See rating plate on the stove Intended area of use Heating of rooms in residential buildings Fuel Wood MANUFACTURER Name NIBE AB / Contura Address Box 134, Skulptörvägen 10 SE-285 23 Markaryd, Sweden CHECKS According to AVCP System 3 European standard...
-
Page 3: Table Of Contents
A warm welcome to Contura A warm welcome to the Contura family. We hope you will get a great deal of pleasure from your new stove. As a new owner of a Contura stove, you have secured a pro- duct with timeless design and long service life. Contura also has a combustion process that is both environmen- tally friendly and efficient, for the best heat production. -
Page 4: Technical Specifications
This folder contains instructions on how to assemble and horizontal sections. A horizontal flue length of up to 1.0 metre is install stoves in the Contura 460. The stove also comes with permissible, provided that the vertical flue is at least 5.0 metres in comprehensive Lighting and Maintenance Instructions. -
Page 5: Installation Distances To Walls And Ceiling
Installation distances to walls and ceiling Lay the metal template as a base-plate (see page 8) where the of the chimney. The rear edge of the template must be flush in stove is to stand and measure to make sure that the stove is line with the rear edge of the concrete surround. -
Page 6: Air Supply
Air supply Important! To prevent condensation in air ducts which pass through heated Combustion air for the stove can be supplied through a duct areas, the duct must be insulated with 30 mm of mineral wool directly from outside, or indirectly through a vent in the wall of covered with aluminium tape. -
Page 7: Unpacking
Unpacking Lift and transport the stove as shown in the sketch! The cast-iron door and fire-bed may be re moved to make the stove lighter and easier to move. First remove all the components from the fire-box and place the steel profiles and metal plates on one side. -
Page 8: Fitting The Fire-Box Surrond
Lift the door upwards until it disengages from the lower hinge. Ease the bottom of the door slightly sideways until it clears the hinge pin. Lower the door to disengage it completely. Fitting the fi re-box surrond Remove the cast-iron cover strips below the side windows. Unscrew the metal brackets from the rear edge of the side windows. -
Page 9: Positioning The Base-Plate
Positioning the base-plate The metal template indicates the position of the stove body, the concrete surround and the hole in the ceiling for the flue. The rear edge of the surround will later be aligned exactly with the rear edge of the template. Place the base-plate on the floor –... -
Page 10: Fitting The Rear Panel
Fitting the rear panel Vent screen Rear panel Secure the vent screen to the rear panel. Screw the rear panel to the supporting profiles of the stove body. -
Page 11: Positioning The Fire-Box
Positioning the fire-box Position the fire-box on the template so that the front legs are centred over the markings. Fit the fan (optional accessory) in accordance with the Installation Instructions for Fan 2000/C460. Installing the heat-retaining blocks Place the seven olivine blocks on the ledge as shown. Top flue connection to steel chimney Follow the instructions on page 7 when making a hole through the ceiling. -
Page 12: Rear Flue Connection To Masonry Chimney
Rear flue connection to masonry chimney Mark out the centre of the hole to be made in the wall for a rear Check the height to make sure that the hole aligns with the flue connection. Make a hole at least 180 mm in diameter and then chimney connection on the rear of the stove. -
Page 13: Assembling The Concrete Surround
Assembling the concrete surround Before starting the assembly work, check to make sure that none of the concrete components have any hairline cracks that run all the way through. When assembling the surround, use the cement supplied to bond the sections together. Mix 1 part water with 2 parts cement. - Page 14 File off any uneven edges on the inside of the door. Screw the Place the hatch in the gap in the plinth and make drilling marks. mounting plate for the hinge into place in the pre-drilled holes in the door, and then fit the hinge to the mounting plate. If a fan is to be connected, make holes for the cables either in the wall or in the back of the plinth.
- Page 15 The gap between the rebate in the concrete components and the rear panel must be carefully sealed with silicone. This is necessary to prevent the wrong kind of convection currents in the warm air. Squeeze out a liberal amount of silicone all along the edge of the rear panel.
- Page 16 Dab a few heaps of cement on the mantelshelf and lift the hood base into place. Use silicone to attach the In this instance it is extra important cover to the rear wall. to make sure that there is a tight seal between the concrete surro und and the rear panel as hot air will be collecte d in this cavity.
- Page 17 Lay the first insulating block on top of the sealing plate. Make sure that the insulation forms a tight seal around the flue base Skorstensmodul (the start section of the flue) and the concrete surround. Then fit Chimney module the second insulating block in place. This has a larger hole in the middle and should form a tight seal with the outside of the chimney Övergångsisolering module.
- Page 18 Cement the remaining concrete sections into place together with any height-extension pieces that may be necessary. Leave a gap of at least 20 mm between the top of the chimney surround and the ceiling. Fill the two expansion gaps in the hood with acrylic sealant.
- Page 19 Use the adhesive to fill the gaps between the different sections of the chimney hood, adding pieces of fibre-glass tape to reinforce the seal. The adhesive should also be used to fill the gap between the hood and the marble slabs of the shelf. The gap between the concrete surround and the marble shelf is filled with acrylic sealant.
-
Page 20: How To Use The Stove
How to use the stove Pulling out the damper bar opens the grate disc. This should only Under normal conditions we recommend that the stove burns 2 be done for a short time when lighting or re-stoking the fire to kg of wood per hour. - Page 24 NIBE AB · Box 134 · 285 23 Markaryd · Sweden www.contura.se Contura reserves the right to change dimensions and procedures described in these instructions at any 611326 IAV EX C460-9 time without special notice. The current edition can 2014-01-23...