Victory Motorcycles 2010 Victory Cross Roads Rider's Manual

Table of Contents

Quick Links

Victory Cross Roads

2010

Rider's Manual

Victory Cross Country

Table of Contents

Chapters

Table of Contents

Summary of Contents for Victory Motorcycles 2010 Victory Cross Roads

Page 1 2010 2010 Rider’s Manual Rider’s Manual Victory Cross Roads Victory Cross Roads Victory Cross Country Victory Cross Country...
Page 2 For your nearest VICTORY dealer, call 1-800-POLARIS or visit www.polarisindustries.com Polaris Sales Inc., 2100 Hwy. 55, Medina, MN 55340 Phone 1-888-704-5290 Part No. 9922671 Rev 01 Printed in USA...
Page 3 inside cover.fm Page 202 Monday, May 11, 2009 1:31 PM California Proposition 65 Warning This product contains or emits chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.
Page 4 inside back cover Vision.fm Page 202 Monday, May 11, 2009 1:31 PM The text is printed on 100% recycled with 40% post-consumer waste (PCW).
Page 6: Introduction
All reference to RIGHT, LEFT, FRONT, REAR are from the operator’s perspective seated in a normal riding position. Features of VICTORY Motorcycles are covered by U.S. Patent Nos: 6,976,691; 6,407,663; D489670; D482311; D482304; D481980; D481973; D474142.
Page 7 Introduction Trademarks The following are registered trademarks of Polaris Industries Inc. POLARIS® THE WAY OUT® VICTORY MOTORCYCLES® VICTORY® FREEDOM® VICTORY CROSS ROADS™ and VICTORY CROSS COUNTRY™ are trademarks of Polaris Industries Inc. DUNLOP® is a registered trademark of Dunlop Tire Corporation.
Page 8: Before You Ride
9922671.book Page 4 Tuesday, June 16, 2009 12:06 PM Introduction WARNING Failure to follow recommended precautions and procedures could result in severe injury or death. Always heed all safety precautions and follow all operation, inspection and maintenance procedures outlined in this manual. Before You Ride Read your Rider’s Manual This rider’s manual contains information that is essential to safe riding and proper mainte-...
Page 9: Table Of Contents
02 Table of Contents.fm Page 5 Tuesday, June 16, 2009 12:30 PM Table of Contents Introduction ..........2 Safety .
Page 10 02 Table of Contents.fm Page 6 Tuesday, June 16, 2009 12:30 PM Table of Contents Audio System..........256 System Overview .
Page 11: Safety
9922671.book Page 7 Tuesday, June 16, 2009 12:06 PM Safety Safety Symbols and Signal Words The following signal words and symbols appear throughout this manual. Your safety and the safety of others is involved when these words and symbols are used. Become familiar with their meanings before reading the manual.
Page 12: Safe Riding Practices
9922671.book Page 8 Tuesday, June 16, 2009 12:06 PM Safety Safe Riding Practices WARNING! Improper use of this motorcycle can result in serious injury or death to you, your passenger and others. To minimize the risk of injury, read and understand the information contained in this section before operating the motorcycle.
Page 13 9922671.book Page 9 Tuesday, June 16, 2009 12:06 PM Safety Safe Riding Practices • Your ability to safely operate the motorcycle depends on your judgment and your use of safe riding habits. Take a rider education course from the Motorcycle Safety Foundation or another qualified instructor.
Page 14 104. Failure to do so can result in serious engine damage. • Some VICTORY motorcycles include saddlebags, a windshield, a trunk, or a passenger backrest as standard equipment. To maintain stability, be prepared to reduce the operating...
Page 15 9922671.book Page 11 Tuesday, June 16, 2009 12:06 PM Safety Safe Riding Practices Follow these general safe riding practices: • Before each ride, perform the pre-ride inspections as outlined beginning on page 81. Fail- ure to do so may result in damage to the motorcycle or an accident. •...
Page 16 9922671.book Page 12 Tuesday, June 16, 2009 12:06 PM Safety Safe Riding Practices • Do not ride when you're fatigued or under the influence of alcohol, prescription drugs, over-the-counter drugs or any other drugs. Fatigue, alcohol and drugs can cause drowsi- ness, loss of coordination and loss of balance.
Page 17 9922671.book Page 13 Tuesday, June 16, 2009 12:06 PM Safety Safe Riding Practices • Be especially cautious at intersections, as these are the most likely places for an accident. • To prevent loss of control, keep your hands on the handlebars and your feet on the foot- rests.
Page 18 9922671.book Page 14 Tuesday, June 16, 2009 12:06 PM Safety Safe Riding Practices • Reduce speed when: • the road has potholes, or is otherwise rough or uneven. • the road contains sand, dirt, gravel or other loose substances. • the road is wet, icy or oily. •...
Page 19 9922671.book Page 15 Tuesday, June 16, 2009 12:06 PM Safety Safe Riding Practices • To maximize braking effectiveness, use the front and rear brakes together. Improper brak- ing may cause loss of control or may not slow the vehicle in time to avoid a collision. Be aware of the following braking facts and practices: •...
Page 20 9922671.book Page 16 Tuesday, June 16, 2009 12:06 PM Safety Safe Riding Practices • When approaching a curve, choose a speed and lean angle that allows you to pass through the curve in your own lane without applying the brakes. Excessive speed, improper lean angle or braking in a curve can cause loss of control.
Page 21: Parking The Motorcycle
9922671.book Page 17 Tuesday, June 16, 2009 12:06 PM Safety Parking the Motorcycle When leaving the motorcycle unattended, turn the engine off. Remove the ignition key to prevent unauthorized use. Park the motorcycle where people are not likely to touch the hot engine or exhaust system or place combustible materials near these hot areas.
Page 22: Carrying A Passenger
9922671.book Page 18 Tuesday, June 16, 2009 12:06 PM Safety Carrying a Passenger Not all models are equipped from the factory with a passenger seat and passenger footrests. Do not carry a passenger unless the motorcycle is equipped with passenger seat and passen- ger footrests.
Page 23 9922671.book Page 19 Tuesday, June 16, 2009 12:06 PM Safety Carrying a Passenger • To obtain the best ride and handling characteristics, adjust the rear shock absorber air pres- sure. See page 160. • Before riding, be sure your passenger knows safe riding procedures. Discuss any safety information unfamiliar to your passenger.
Page 24 9922671.book Page 20 Tuesday, June 16, 2009 12:06 PM Safety Carrying Cargo Use the following guidelines when attaching cargo or accessories to the motorcycle. Where applicable, these guidelines also refer to the contents of any accessories. • Keep cargo and accessory weight to a minimum, and keep items as close to the motorcycle as possible to minimize a change in the motorcycle’s center of gravity.
Page 25 9922671.book Page 21 Tuesday, June 16, 2009 12:06 PM Safety Carrying Cargo • Do not attach large or heavy cargo such as sleeping bags, duffel bags or tents to the han- dlebars, front fork area or front fender. Cargo or accessories placed in these areas can cause instability (due to improper weight distribution or aerodynamic changes) and could cause loss of control.
Page 26: Protective Apparel
9922671.book Page 22 Tuesday, June 16, 2009 12:06 PM Safety Protective Apparel Wear protective apparel to decrease the risk of injury and increase riding comfort. • Always wear a helmet that meets or exceeds established safety standards. Approved hel- mets in the USA and Canada bear a U.S. Department of Transportation (DOT) label. Laws in some areas require that you wear an approved helmet.
Page 27 9922671.book Page 23 Tuesday, June 16, 2009 12:06 PM Safety Protective Apparel • All riders should wear bright or light-colored and/or reflective clothing to improve visibil- ity to other motorists. A motorist's failure to see or recognize a motorcycle is the leading cause of automobile/motorcycle accidents.
Page 28 9922671.book Page 24 Tuesday, June 16, 2009 12:06 PM Safety Use of Accessories Because VICTORY cannot test and make specific recommendations concerning every acces- sory or combination of accessories sold, the operator is responsible for determining that the motorcycle can be safely operated with any accessories or additional weight. Use the follow- ing guidelines when choosing and installing accessories: •...
Page 29 9922671.book Page 25 Tuesday, June 16, 2009 12:06 PM Safety Use of Accessories • Do not install electrical accessories that exceed the capacity of the motorcycle’s electrical system. Never install higher wattage light bulbs than those supplied as original equipment. An electrical failure could result and cause hazardous loss of engine power or lights, or damage to the electrical system.
Page 30 9922671.book Page 26 Tuesday, June 16, 2009 12:06 PM Safety Saddlebags WARNING! Operating this vehicle without saddlebags could result in severe injury or death. Never operate this vehicle if the saddlebags are not in place and properly secured. Whenever operating a motorcycle with saddlebags: •...
Page 31: Transporting The Motorcycle
9922671.book Page 27 Tuesday, June 16, 2009 12:06 PM Safety Transporting the Motorcycle If you must transport the motorcycle: To lower triple clamp (one tiedown each side) • Use a truck or trailer. Do not tow the motorcycle with another vehicle, as towing will impair the motorcycle's steering and handling.
Page 32 9922671.book Page 28 Tuesday, June 16, 2009 12:06 PM Safety Fuel and Exhaust Safety Always heed these fuel safety warnings when refueling or servicing the fuel system. For fueling procedures, see page 106. WARNING! Gasoline is highly flammable and explosive under certain conditions. •...
Page 33 9922671.book Page 29 Tuesday, June 16, 2009 12:06 PM Safety Fuel and Exhaust Safety WARNING! Gasoline and gasoline vapors are poisonous and can cause severe injury. • Do not swallow gasoline, inhale gasoline vapors, or spill gasoline. If you swallow gasoline, inhale more than a few breaths of gasoline vapor, or get gasoline in your eyes, see a physician immediately.
Page 34 9922671.book Page 30 Tuesday, June 16, 2009 12:06 PM Safety Safety Maintenance WARNING! Failure to perform safety maintenance as recommended can result in difficult handling and loss of control, which could result in serious injury or death. Always perform the safety maintenance procedures as recommended.
Page 35: Electromagnetic Interference
9922671.book Page 31 Tuesday, June 16, 2009 12:06 PM Safety Safety Maintenance • Always ensure proper steering head bearing adjustment. Regularly inspect the rear shock absorber and the front forks for fluid leaks or damage. Make any necessary repairs promptly. •...
Page 36 9922671.book Page 32 Tuesday, June 16, 2009 12:06 PM Safety Gross Vehicle Weight Rating (GVWR) WARNING! Exceeding the gross vehicle weight rating of your motorcycle can reduce stability and han- dling and could cause loss of control. NEVER exceed the GVWR of your motorcycle. The maximum load capacity of your motorcycle is the maximum weight you may add to your motorcycle without exceeding the GVWR.
Page 37 9922671.book Page 33 Tuesday, June 16, 2009 12:06 PM Safety Gross Vehicle Weight Rating (GVWR) When determining the weight you will be adding to your motorcycle, and to ensure you do not exceed the maximum load capacity, include the following: •...
Page 38 9922671.book Page 34 Tuesday, June 16, 2009 12:06 PM Safety Safety and Information Labels 1. Vehicle Identification Number (VIN) 5. Cargo Information (in saddlebags) 2. Vehicle Emission Control Information (VECI) 6. Shock Air Pressure label 3. Noise Emission Control Information (NECI) 7.
Page 39: Reporting Safety Defects
9922671.book Page 35 Tuesday, June 16, 2009 12:06 PM Safety Reporting Safety Defects If you believe that your vehicle has a defect that could result in a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Polaris Industries in writing.
Page 40: Component Identification
9922671.book Page 36 Tuesday, June 16, 2009 12:06 PM Identification Ignition Key Number Key Number The ignition key number is stamped on the small metal tag attached to the key ring. Remove the tag and record the number on page 37. Store the tag in a safe place. Additional keys can be copied from one of the original keys.
Page 41: Identification Number Record
9922671.book Page 37 Tuesday, June 16, 2009 12:06 PM Identification Identification Number Record Record important identification numbers below. Vehicle Identification Number (VIN) (see page 34) Engine Identification Number (see page 36) Ignition Key Number (see page 36)
Page 42 9922671.book Page 38 Tuesday, June 16, 2009 12:06 PM Identification Component Locations 1. Spark Plugs 2. Front Brake Caliper 3. Oil Cooler 4. Battery 5. Gear Shift Pedal 6. Operator Footrest 7. Sidestand 8. Oil Drain Plug 9. Oil Filter 10.
Page 43 9922671.book Page 39 Tuesday, June 16, 2009 12:06 PM Identification Component Locations 1. Exhaust Mufflers 2. Drive Belt Guard 3. Drive Sprocket (under cover) 4. Engine Oil Fill Cap / Dipstick 5. Rear Brake Fluid Reservoir 6. Rear Brake Pedal 7.
Page 44 9922671.book Page 40 Tuesday, June 16, 2009 12:06 PM Identification Component Locations 1. Windshield 2. Clutch Lever 3. Fuel Filler Cap 4. Operator Seat 5. Passenger Seat 6. Saddlebag Latch 7. Turn Signals 8. Tail Lamps 9. Front Brake Lever 10.
Page 45: Component Locations
9922671.book Page 41 Tuesday, June 16, 2009 12:06 PM Identification Component Locations 1. Speakers 9. Left Handlebar Switches 2. Mode Switch 10. Audio Control Switches 3. Fuel Gauge 11. +12-Volt Accessory Outlet 4. Speedometer 12. Radio Display 5. Indicator Lamp Display 13.
Page 46: Instruments/Features/Controls
9922671.book Page 42 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Ignition Switch The ignition key operates the ignition switch and parking lights. The ignition switch pro- vides electrical power to the ignition, the lighting system and all electrical switches and buttons.
Page 47: Ignition Switch
9922671.book Page 43 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Ignition Switch In the ON position, all electrical circuits are energized and the ignition key cannot be removed. The headlamp, taillight, and instrument lights illuminate. The engine stop/run switch must be in the RUN position to start the engine or activate the turn signals and other electrical features.
Page 48 9922671.book Page 44 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Roads) Speedometer Speedometer The speedometer displays vehicle speed in either miles per hour (MPH) or kilometers per hour (km/h). Multi-Function Display Use the mode button to toggle through the modes of the multi- function display.
Page 49 9922671.book Page 45 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Roads) Multi-Function Display Odometer The odometer displays total distance traveled. Trip Odometers The ignition switch must be in the ON or PARK position to access the trip odometers. The trip odometers (Trip 1 and Trip 2) display total distance traveled since being reset.
Page 50 9922671.book Page 46 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Roads) Multi-Function Display Clock Tip: The clock must be reset any time the battery has been disconnected or discharged. 1. Turn the key to ON or PARK. Toggle to the clock display. 2.
Page 51 9922671.book Page 47 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Roads) Multi-Function Display Trip Hours Meter The trip hours meter displays total hours of operation since being reset. To reset the trip hours meter, toggle to the hours meter display, then press and hold the mode button until the meter resets to zero.
Page 52 9922671.book Page 48 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Roads) Indicator Lamps Lamp Indicates Condition Neutral This lamp illuminates when the transmission is in neutral and the ignition key is in the ON position. High Beam This lamp illuminates when the headlamp switch is set to high beam.
Page 53 9922671.book Page 49 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Roads) Indicator Lamps Lamp Indicates Condition Low Fuel This lamp illuminates when approximately one gallon (3.8 liters) of fuel remains in the fuel tank. CKENG Check Engine The check engine message appears in the multi-function display.
Page 54 9922671.book Page 50 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Country) The instrument cluster includes the speedometer, tachometer, fuel gauge, volt meter, indica- tor lamps and multi-function display. Indicator Lamps Tachometer Speedometer Volt Meter Fuel Gauge Multi-Function Display...
Page 55 9922671.book Page 51 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Country) Speedometer Fuel Gauge The speedometer displays vehicle speed in The fuel gauge displays fuel level. The key either miles per hour or kilometers per hour. must be in the ON or PARK position. For the most accurate reading, sit on the motor- Tachometer cycle and bring it to the upright position.
Page 56 9922671.book Page 52 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Country) Indicator Lamps Right Turn High Beam Low Fuel Left Turn Oil Pressure Cruise Control Check Engine Battery Warning Neutral...
Page 57 9922671.book Page 53 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Country) Indicator Lamps Lamp Indicates Condition Neutral This lamp illuminates when the transmission is in neutral and the ignition key is in the ON or PARK position. High Beam This lamp illuminates when the headlamp switch is set to high beam.
Page 58 9922671.book Page 54 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Country) Indicator Lamps Lamp Indicates Condition Turn Signal One arrow flashes when the corresponding turn signal is activated. Both arrows flash when the hazard signal is activated. If a bulb fails, or if there is a short circuit in the signal system, the lamp flashes at more than twice the normal rate.
Page 59 9922671.book Page 55 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Country) Indicator Lamps Lamp Indicates Condition Low Fuel This lamp illuminates when approximately one gallon (3.8 liters) of fuel remains in the fuel tank. Low Battery This lamp illuminates when battery voltage is low. Make sure the Warning charging system is operating properly.
Page 60 9922671.book Page 56 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Country) Multi-Function Display Use the mode button to toggle through the Clock modes of the multi-function display. See page 66. Gear Permanently Displayed Modes Position • Clock •...
Page 61 9922671.book Page 57 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Country) Multi-Function Display Engine Error Codes Error Code Failure Mode Number (0-9) Indicator (FMI) The error screen displays only when the CHECK ENGINE light is on or when it goes on and off dur- ing one ignition cycle.
Page 62 9922671.book Page 58 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Country) Multi-Function Display Display Units (Standard/Metric) The display can be changed to display either standard or metric units of measurement. Tip: To exit the set-up mode at any time, wait 10 seconds.The display automatically exits and returns to the odometer display.
Page 63 9922671.book Page 59 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Country) Multi-Function Display Display Units (Standard/Metric) 1. Turn the key to the OFF position. 2. Press and hold the mode button while turning the key to the ON or PARK position. 3.
Page 64 9922671.book Page 60 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Country) Multi-Function Display Clock Tip: The clock must be reset any time the battery has been disconnected or discharged. 1. Turn the key to ON or PARK. Use the mode button to toggle to the odometer display. Tip: If LOW FUEL is flashing, the display will not enter the CLOCK SET mode.
Page 65 9922671.book Page 61 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Instrument Cluster (Cross Country) Multi-Function Display Odometer/Trip Odometer The odometer displays the total distance traveled by the vehicle. The trip odometer displays distance traveled since the trip odometer was reset. To view the trip odometer, turn the key to the ON position.
Page 66 9922671.book Page 62 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Console Switches (Cross Country) Hand Grip Optional Accessory Heater Switch Switch...
Page 67 9922671.book Page 63 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Console Switches (Cross Country) Hand Grip Heater Switch High Press the top (high heat) or bottom (low heat) of the rocker switch to turn the hand grip heaters on. Move the switch to the center position to turn the heat- ers off.
Page 68: Left Handlebar Switches
9922671.book Page 64 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Left Handlebar Switches High/Low Light Switch Flasher (Hazard) Switch Turn Signal Switch Horn Button Lamp Switch Description Emergency The emergency flasher switch activates and cancels the emergency Flasher Switch flashers. When the emergency flashers are active, all of the turn signals (Hazard Switch) flash.
Page 69 9922671.book Page 65 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Left Handlebar Switches Lamp Switch Description High Beam/Low The headlight high/low beam switch toggles the headlight between high Beam Light beam and low beam. To activate the high beam, press the upper portion Switch of the switch;...
Page 70 9922671.book Page 66 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Left Handlebar Switches Audio Switches (if equipped) Refer to the Audio System section of this manual (beginning on page 256) for audio systems operation. Mode Button The mode button is located on the front side of the left handlebar switch.
Page 71 9922671.book Page 67 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Left Handlebar Switches Starter Interlock Switch The starter interlock switch is located on the left han- dlebar. This switch prevents the electric starter from operating when the transmission is in gear and the clutch is engaged (lever released).
Page 72: Right Handlebar Switches
9922671.book Page 68 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Right Handlebar Switches Engine Stop/Run Switch Stop The engine stop/run switch is located on the right handlebar. This switch completes or interrupts the ignition, starter and fuel pump circuits. Use the engine stop/run switch to turn the engine off quickly.
Page 73 9922671.book Page 69 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Right Handlebar Switches Engine Starter Switch The starter switch is located on the right handlebar. Use the starter switch to start the engine and operate in reverse (if equipped). The switch will operate only when the engine stop/ run switch is in the RUN position and the transmission is in neutral (or the clutch is disengaged).
Page 74: Clutch Lever
9922671.book Page 70 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Clutch Lever The clutch lever is located on the left handlebar. Disen- gage the clutch before shifting gears. For smooth clutch operation, pull the lever quickly and release it gradu- ally.
Page 75: Throttle Control Grip
9922671.book Page 71 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Throttle Control Grip The throttle control grip is located on the Decrease right handlebar. Use the throttle control grip Speed to control engine speed. While seated in the proper riding position: •...
Page 76 9922671.book Page 72 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Brakes The front brake lever activates the front brake calipers. The rear brake pedal activates the rear brake caliper. For maximum brake effectiveness, apply the front brake lever and the rear brake pedal together.
Page 77 9922671.book Page 73 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Brakes Front Brake Lever Front brake lever reach (distance to the hand grip) is adjustable. 1. Pull and hold the lever away from the hand grip. 2. To increase reach distance, rotate the Pull and hold lever adjuster to align a lower number with the arrow on the lever.
Page 78 9922671.book Page 74 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Brakes Rear Brake Pedal The rear brake pedal is located on the right side of the motorcycle. Press downward on the rear brake pedal to apply the rear brake. The rear brake pedal activates the rear brake caliper fully.
Page 79 9922671.book Page 75 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Gear Shift Pedal The gear shift pedal is located on the left side of the motorcycle. • Press downward on the gear shift pedal to shift to a lower gear. •...
Page 80 9922671.book Page 76 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Pedal Adjustment The brake pedal and gear shift pedal controls can be adjusted to a front, rear or center position. The center position is the factory setting. 1. Remove the screw from the footwell support. Tool: 6 mm Allen wrench 2.
Page 81 9922671.book Page 77 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Sidestand The sidestand is located on the left side of the motorcycle. WARNING! An improperly retracted sidestand could contact the ground and cause a loss of control resulting in serious injury or death. Always retract the sidestand fully before operating the motorcycle. To park the motorcycle, swing the end of the sidestand down- ward and away from the motorcycle until it is fully extended.
Page 82 9922671.book Page 78 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Saddlebag Lock Use the ignition key to lock and unlock the saddlebag Unlock doors. The doors should be locked before riding. To lock a door, place the key in the lock and turn it counter-clockwise.
Page 83: Fuel Filler Cap
9922671.book Page 79 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Fuel Cap Use the ignition key to lock and unlock the fuel cap. Always lock the fuel cap before riding. An open fuel cap could contact the handlebars. To open the fuel cap, lift the lock cover. Place the key in the lock and turn it clockwise.
Page 84: Tool Kit
9922671.book Page 80 Tuesday, June 16, 2009 12:06 PM Instruments/Features/Controls Tool Kit The tool kit can be used to perform most basic maintenance items. Tools provided in the tool kit include: 1. 4 mm Ball Drive Allen Wrench 2. 5 mm Ball Drive Allen Wrench 3.
Page 85: Pre-Ride Inspections
9922671.book Page 81 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections To keep your motorcycle in safe operating condition, always perform the recommended pre- ride inspections before each ride. This is especially important before making a long trip and when removing the motorcycle from storage. WARNING! Failure to perform the recommended pre-ride inspections could result in component failure while riding, which could result in serious injury or death.
Page 86: Turn Signals
9922671.book Page 82 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Turn the ignition key to the ON position and move the stop/run switch to RUN before per- forming the following electrical inspections. Return the ignition key to the OFF position after completing these inspections.
Page 87 9922671.book Page 83 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Item Inspection Procedure Electrical Emergency Press the top of the hazard switch to turn the flashers on. Verify that all four turn Flashers signals flash, as well as the lamps on the indicator panel. Turn the flashers off. Verify that all signals and indicator lamps stop flashing.
Page 88 9922671.book Page 84 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Item Inspection Procedure See Page General Engine Oil Level Check the oil level on the dipstick. Fuel Level View the fuel gauge or information bar. Tires Inspect condition, pressure and tread depth. Brake Operation Inspect pedal and lever movement.
Page 89 9922671.book Page 85 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Item Inspection Procedure See Page General Clutch (Mechanical) Check lever operation and freeplay. Front Suspension Check for leaks, debris and damage. Steering Check for smooth operation. Rear Suspension Check shock movement and air pressure, verify ground clearance.
Page 90: Engine Oil Level
9922671.book Page 86 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Engine Oil Level The oil fill cap/dipstick is located on the right side of the vehicle. Always use the recommended oil. See page 255. Tip: The engine must be at normal operating temperature when checking the oil level.
Page 91 9922671.book Page 87 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Engine Oil Level 5. Remove the oil fill cap/dipstick and wipe it clean. Reinstall the dipstick and turn the cap clockwise until it seats. 6. Remove the dipstick and view the oil level. Safe Range 7.
Page 92: Fuel Level
9922671.book Page 88 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Fuel Level 1. On level ground, straddle the motorcycle and bring it to the fully upright position. 2. Turn the ignition switch to the ON or PARK position. View the fuel level in the fuel gauge (Cross Country), or use the MODE button to toggle to the fuel display in the information bar (Cross Roads).
Page 93 9922671.book Page 89 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Tires Tire Pressure Check tire pressure before riding, when the tires are cold. This will provide the most accurate reading, as riding warms the tires and increases tire air pressure. Adjust tire pressure as needed based on the total weight of your intended load.
Page 94: Front Brake Lever
9922671.book Page 90 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Front Brake Lever 1. Pull the front brake lever toward the Minimum Level handlebar and hold it. The lever should move freely and smoothly. It should not move more than 3/4 inch (19 mm) before resistance is firm.
Page 95 9922671.book Page 91 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Front Brake Fluid Level 1. Straddle the motorcycle and bring it to the fully upright position. Position the handlebars so that the fluid reservoir is level. 2. View the fluid level through the sight glass. The fluid should be clear. Replace cloudy or contaminated fluid.
Page 96 9922671.book Page 92 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Rear Brake Pedal 1. Press downward on the rear brake pedal. It should move freely and smoothly. It should not move more than 3/8 inch (8 mm) before resistance is firm. It should continue to feel firm, without loss of pres- sure, until the pedal is released.
Page 97 9922671.book Page 93 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Rear Brake Fluid Level The rear brake fluid reservoir is located near the rear brake pedal. View the reservoir from the front right side of the vehicle. 1. Position the motorcycle on level ground in the fully upright position.
Page 98 9922671.book Page 94 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Brake Lines Inspect all brake hoses and connections for dampness or stains from leaking or dried fluid. Tighten any leaking connections and replace components as necessary. Tip: Refer to the service manual or contact your dealer for fastener torque values. WARNING! Brake fluid leaks or low brake fluid levels could cause brake system failure, which could result in serious injury or death.
Page 99: Brake Pads
9922671.book Page 95 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Brake Pads Inspect each front brake pad on both sides of Friction the front disc. Inspect each rear brake pad on Material both sides of the rear disc. When the thinnest point of the friction material has worn to the minimum recommended thickness, see your VICTORY dealer for brake pad replacement.
Page 100 9922671.book Page 96 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Throttle Rotate the throttle control grip. It should rotate smoothly from the rest position to the completely open position. It should return to the rest position quickly when released. Throttle Freeplay Throttle freeplay is the amount of throttle 2-4 mm to...
Page 101 9922671.book Page 97 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Mechanical Clutch 1. Squeeze the clutch lever toward the handlebar and release it. It should move freely and smoothly, and it should return to the rest posi- tion quickly when released. If the lever fails to perform as stated, service the clutch lever before riding.
Page 102: Front Suspension
9922671.book Page 98 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Front Suspension Inspect the front forks for oil leaks or damage, and verify smooth suspension operation. See page 167. Steering 1. On level ground, straddle the motorcycle and bring it to the fully upright position. Turn the handlebars from stop to stop.
Page 103: Rear Suspension
9922671.book Page 99 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Rear Suspension 1. Check rear shock absorber movement and air pressure to ensure the correct amount of suspension travel and ground clearance. 2. For air pressure adjustment information, see page 160 or refer to the suspension air pres- sure label located in the left saddlebag near the air fitting.
Page 104: Drive Belt
9922671.book Page 100 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Drive Belt 1. Check drive belt tension. See page 153. The drive belt should fit tightly. Tip: The drive belt system must be cool, clean and dry to accurately measure belt tension (deflection). Do not measure belt tension when the belt or drive system is wet, or when it is hot (such as immediately after riding).
Page 105 9922671.book Page 101 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Sidestand 1. On level ground, straddle the motorcycle and bring it to the fully upright position. 2. Move the sidestand up to the stored position and down to the fully extended position sev- eral times.
Page 106 9922671.book Page 102 Tuesday, June 16, 2009 12:06 PM Pre-Ride Inspections Fasteners 1. Inspect the entire motorcycle chassis and engine for loose, damaged or missing fasten- ers. Tighten loose fasteners to the proper torque. Tip: Refer to the specifications section of this manual or the service manual for fastener torque values, or see your VICTORY dealer.
Page 107: Operation
9922671.book Page 103 Tuesday, June 16, 2009 12:06 PM Operation The operation section of this manual describes how to ensure maximum performance and longevity through the proper care and operation of your motorcycle. Tip: Even if you're an experienced motorcycle operator or passenger, read all of the safety information in this manual before operating the motorcycle.
Page 108 9922671.book Page 104 Tuesday, June 16, 2009 12:06 PM Operation Engine Break-In The engine break-in period for your motorcycle is the first 500 miles (800 km) of operation. During this break-in period, critical engine parts require special wear-in procedures so they seat and mate properly.
Page 109 9922671.book Page 105 Tuesday, June 16, 2009 12:06 PM Operation Engine Break-In Odometer Break-in Procedure Miles 0-90 0-145 Do not operate for extended periods above 1/3 throttle or at any one throttle position. Vary engine speed frequently. 91-300 146-483 Do not operate for extended periods above 1/2 throttle or at any one throttle position.
Page 110 9922671.book Page 106 Tuesday, June 16, 2009 12:06 PM Operation Fueling Always refuel on level ground with the sidestand down. Review the fuel warnings. See page 28. Use only the recommended fuel. See page 255. Hold the nozzle while filling. Do not rest the weight of the nozzle and hose on the filler neck.
Page 111 9922671.book Page 107 Tuesday, June 16, 2009 12:06 PM Operation Priming the Fuel System If the motorcycle runs out of fuel, prime the fuel system before attempting to restart the engine. 1. Fill the fuel tank. 2. Turn the ignition key to the ON position. 3.
Page 112: Starting The Engine
9922671.book Page 108 Tuesday, June 16, 2009 12:06 PM Operation Starting the Engine The starter interlock system allows the engine to be started only when the transmission is in neutral, or when the transmission is in gear with the clutch disengaged (clutch lever pulled in).
Page 113 9922671.book Page 109 Tuesday, June 16, 2009 12:06 PM Operation Starting the Engine 7. Apply the front brakes. 8. Leaving the throttle closed, press and hold the starter switch to start the engine. Release the switch promptly when the engine starts. If the engine does not start within 10 sec- onds, release the starter switch.
Page 114: Shifting Gears
9922671.book Page 110 Tuesday, June 16, 2009 12:06 PM Operation Shifting Gears WARNING! Forced shifting (with clutch engaged) could cause damage to the engine, transmission and drive train. Such damage could cause loss of control, which could result in serious injury or death. Always pull the clutch lever fully toward the handlebars to disengage the clutch before shifting gears.
Page 115 9922671.book Page 111 Tuesday, June 16, 2009 12:06 PM Operation Shifting Gears 1. Start the engine. See page 108. 2. With the engine at idle speed, apply the front brakes. 3. Disengage the clutch (pull the clutch lever fully toward the handlebar). 4.
Page 116 9922671.book Page 112 Tuesday, June 16, 2009 12:06 PM Operation Shifting Gears Tip: Within the recommended speed ranges (see page 113), you can downshift to slow the motorcycle or to increase power. You may want to downshift when climbing a hill or passing. Downshifting also helps to decrease speed when combined with closing the throttle.
Page 117 9922671.book Page 113 Tuesday, June 16, 2009 12:06 PM Operation Shifting Gears Recommended Shift Points Upshifting (Accelerating) Downshifting (Decelerating) Gear Change Recommended Speed Gear Change Recommended Speed 1 to 2 18 MPH (29 km/h) O/D to 5 50 MPH (80 km/h) 2 to 3 30 MPH (48 km/h) 5 to 4...
Page 118 9922671.book Page 114 Tuesday, June 16, 2009 12:06 PM Operation Accelerating Accelerate by opening the throttle (rolling the throttle control grip rearward). For even accel- eration, open the throttle with a smooth, continuous motion. When you reach the recom- mended speed for upshifting, shift up one gear. WARNING! Accelerating abruptly could cause your body to shift rearward suddenly, which could result in loss of control.
Page 119 9922671.book Page 115 Tuesday, June 16, 2009 12:06 PM Operation Braking Always allow sufficient stopping distance so that brakes can be applied gradually. Tip: Applying slightly more front brake than rear brake generally provides the best braking perfor- mance. 1. To slow the motorcycle with the brakes, close the throttle and apply the front and rear brakes evenly and gradually.
Page 120 9922671.book Page 116 Tuesday, June 16, 2009 12:06 PM Operation Using Cruise Control (if equipped) If equipped, the cruise control is located on the right handlebar. Read this section and understand how to safely operate this feature before using. WARNING! Improper operation of cruise control could cause loss of control and result in serious injury or death.
Page 121 9922671.book Page 117 Tuesday, June 16, 2009 12:06 PM Operation Using Cruise Control (if equipped) Cruise Control Tips • Cruise control can be set in any gear. • Vehicle speed must be above 25 MPH (40 km/h). • Set speed will vary slightly in hilly terrain. •...
Page 122 9922671.book Page 118 Tuesday, June 16, 2009 12:06 PM Operation Using Cruise Control (if equipped) Set Speed 1. Press the cruise control ON button. Tip: The cruise control indicator lamp will illuminate when the ON or OFF switch is pressed. 2.
Page 123 9922671.book Page 119 Tuesday, June 16, 2009 12:06 PM Operation Using Cruise Control (if equipped) Resume Speed After disengaging the cruise control with the brake, throttle Resume or clutch, wait at least 3 seconds, then press the resume but- ton (RES) to return to the set speed. If the resume button is pressed within 3 seconds of disengag- ing, the cruise control may not engage, even if the cruise con- trol indicator illuminates.
Page 124 9922671.book Page 120 Tuesday, June 16, 2009 12:06 PM Operation Using Cruise Control (if equipped) Accelerate Tap and release the accelerate (ACC) button to increase speed in approximately 1 MPH (1-2 km/h) increments. Press and hold the ACC button to accelerate to a new SET speed (resets when button is released).
Page 125 9922671.book Page 121 Tuesday, June 16, 2009 12:06 PM Operation Using Cruise Control (if equipped) Decelerate Tap and release the decelerate (DEC) button to decrease speed in approximately 1 MPH (1-2 km/h) increments. Press and hold the DEC button to decelerate to a new SET speed (resets when button is released), or to the minimum cruise speed of 25 MPH (40 km/h).
Page 126: Stopping The Engine
9922671.book Page 122 Tuesday, June 16, 2009 12:06 PM Operation Stopping the Engine Before stopping the engine, bring the motorcycle to a complete stop. Shift to neutral or dis- engage the clutch. WARNING! Stopping the engine with the transmission in gear while the motorcycle is moving could cause loss of rear wheel traction or engine and transmission damage, which could cause loss of control and serious injury or death.
Page 127: Parking On A Slope
9922671.book Page 123 Tuesday, June 16, 2009 12:06 PM Operation Parking Choose a firm level surface to park the motorcycle. 1. When fully stopped, shift into neutral. 2. Stop the engine. 3. Fully extend the sidestand. 4. Turn the handlebars to the left and lean the motorcycle to the left until the sidestand firmly supports the motorcycle.
Page 128 9922671.book Page 124 Tuesday, June 16, 2009 12:06 PM Operation Parking on a Soft Surface If parking on a soft surface is unavoidable, place a sidestand footrest under the foot of the sidestand to provide a firm surface. The sidestand footrest must be strong enough and large enough to support the motorcycle's weight without sinking into the parking surface.
Page 129 9922671.book Page 125 Tuesday, June 16, 2009 12:06 PM Operation Reverse Operation (if equipped) NOTICE: Do not attempt to engage or disengage the reverse system when the motorcycle is moving. Before Operating in Reverse: NEVER Operate in Reverse: • always sit on the motorcycle with legs •...
Page 130 9922671.book Page 126 Tuesday, June 16, 2009 12:06 PM Operation Reverse Operation (if equipped) 1. Always check for obstacles or people behind the motorcycle. Be aware that the front wheel may travel outward and require a larger operating area. 2. Make sure the motorcycle is stationary. 3.
Page 131 9922671.book Page 127 Tuesday, June 16, 2009 12:06 PM Operation Reverse Operation (if equipped) 8. Lift the reverse lever and verify that the reverse indicator (R) displays in the multi-func- tion display. 9. Recheck the area behind and around the motorcycle to ensure a clear operating area. 10.
Page 132: Maintenance
9922671.book Page 128 Tuesday, June 16, 2009 12:06 PM Maintenance Safety During Service Procedures WARNING Failure to follow recommended precautions and procedures could result in severe injury or death. Always heed all safety precautions and follow all operation, inspection and maintenance procedures outlined in this manual.
Page 133 9922671.book Page 129 Tuesday, June 16, 2009 12:06 PM Maintenance Safety During Service Procedures • Hot engine and exhaust components can cause burns to skin and can ignite a fire if exposed to flammable materials. Always park the motorcycle clear of flammable materials and where people are not likely to contact hot components.
Page 134 9922671.book Page 130 Tuesday, June 16, 2009 12:06 PM Maintenance Proper maintenance assures the highest level of safety, durability and dependability for your motorcycle. • Have your VICTORY dealer perform the break-in maintenance procedures when the motorcycle’s odometer registers 500 miles (800 km). •...
Page 135: Major Maintenance
9922671.book Page 131 Tuesday, June 16, 2009 12:06 PM Maintenance Break-In Maintenance Have your VICTORY dealer perform the break-in maintenance procedures when the motor- cycle’s odometer registers 500 miles (800 km). Performing the break-in maintenance will help ensure optimum engine performance for the entire service life of the engine. Your dealer will change engine oil, inspect all fluids and serviceable components, ensure that all fasteners are tightened and make other adjustments as needed.
Page 136: Periodic Maintenance
9922671.book Page 132 Tuesday, June 16, 2009 12:06 PM Maintenance Periodic Maintenance Inspect, clean, lubricate, adjust and replace parts as necessary. When inspection reveals the need for replacement parts, use genuine VICTORY parts available from your VICTORY dealer. Record service and maintenance information in the Maintenance Log beginning on page 138.
Page 137 9922671.book Page 133 Tuesday, June 16, 2009 12:06 PM Maintenance Periodic Maintenance Table See table key below Odometer Reading in Miles (Kilometers) Component Page Air Filter Battery Brake Fluid Brake Pads Clutch Cable Maintenance Key: I = Inspect, clean, adjust, correct or replace if necessary; P = Perform; R = Replace / Rebuild L = Lubricate w/ proper lubricant;...
Page 138 9922671.book Page 134 Tuesday, June 16, 2009 12:06 PM Maintenance Periodic Maintenance Table See table key below Odometer Reading in Miles (Kilometers) Component Page Clutch Lever (Mechanical) Control Cables Crankcase Vent Drive Belt Drive Belt Adjustment Adjust with each tire change thereafter Engine Oil &...
Page 139 9922671.book Page 135 Tuesday, June 16, 2009 12:06 PM Maintenance Periodic Maintenance Table See table key below Odometer Reading in Miles (Kilometers) Component Page Evaporative Emission Control System (if equipped) Exhaust System Fasteners Front Brake Lever Front Fork Oil** Front Fork / Axle Fuel System Maintenance Key: I = Inspect, clean, adjust, correct or replace if necessary;...
Page 140 9922671.book Page 136 Tuesday, June 16, 2009 12:06 PM Maintenance Periodic Maintenance Table See table key below Odometer Reading in Miles (Kilometers) Component Page Gear Shift Pedal Headlamp Ignition Switch / Locks Radio/Radio Software Update annually. Please see your dealer. Rear Wheel Align Rear Shock Rear Brake Pedal...
Page 141 9922671.book Page 137 Tuesday, June 16, 2009 12:06 PM Maintenance Periodic Maintenance Table See table key below Odometer Reading in Miles (Kilometers) Component Page Sidestand Sidestand Pad Spark Plugs Steering Head Bearings Swingarm Throttle Cable Tires Maintenance Key: I = Inspect, clean, adjust, correct or replace if necessary; P = Perform; R = Replace / Rebuild; L = Lubricate w/ proper lubricant;...
Page 142: Maintenance Log
9922671.book Page 138 Tuesday, June 16, 2009 12:06 PM Maintenance Maintenance Log Maintenance Performed Miles / Km Notes Performed...
Page 143 9922671.book Page 139 Tuesday, June 16, 2009 12:06 PM Maintenance Maintenance Log Maintenance Performed Miles / Km Notes Performed...
Page 144 9922671.book Page 140 Tuesday, June 16, 2009 12:06 PM Maintenance Maintenance Log Maintenance Performed Miles / Km Notes Performed...
Page 145 9922671.book Page 141 Tuesday, June 16, 2009 12:06 PM Maintenance Maintenance Log Maintenance Performed Miles / Km Notes Performed...
Page 146 9922671.book Page 142 Tuesday, June 16, 2009 12:06 PM Maintenance Engine Oil / Filter Change Change the engine oil at the intervals specified in the periodic maintenance table beginning on page 133. 1. Start the engine and allow it to idle for several min- utes.
Page 147 9922671.book Page 143 Tuesday, June 16, 2009 12:06 PM Maintenance Engine Oil / Filter Change 4. Slowly loosen the oil filter. Allow the oil to drain completely. Tool: 2 1/2 inch (63.5 mm) oil filter wrench 5. Clean the drain plug sealing surface on the crankcase. 6.
Page 148 9922671.book Page 144 Tuesday, June 16, 2009 12:06 PM Maintenance Engine Oil / Filter Change 10. Start the engine and allow it to idle for several min- utes. Stop the engine. NOTICE: After an oil change, the low oil pressure indicator remains illuminated longer than usual before going out.
Page 149: Air Filter
9922671.book Page 145 Tuesday, June 16, 2009 12:06 PM Maintenance Air Filter Inspect the air filter often if riding in unusually wet or Mounting Screws dusty conditions. Do not apply air filter oil to this air filter. 1. Remove the fuel tank. See page 146. 2.
Page 150 9922671.book Page 146 Tuesday, June 16, 2009 12:06 PM Maintenance Fuel Tank Removal / Installation Before beginning, be prepared to place the fuel tank in a secure location with a drain pan positioned to catch any fuel that may leak or drip from disconnected hoses or fittings. 1.
Page 151 9922671.book Page 147 Tuesday, June 16, 2009 12:06 PM Maintenance Fuel Tank Removal / Installation 6. Lift the rear of the tank to locate the fuel pump electrical connector. Disconnect the connector by lifting the tab slightly. 7. Place the handlebars in the straight ahead position. NOTICE: DO NOT rest the fuel tank on the frame while removing it.
Page 152 08 Maintenance.fm Page 148 Tuesday, June 16, 2009 2:49 PM Maintenance Fuel Tank Removal / Installation 11. To reinstall the fuel tank, reverse the removal steps, routing the fuel line along the right edge directly to the fuel rail. NOTICE: The 90-degree tank fitting can be damaged if improperly installed.
Page 153 9922671.book Page 149 Tuesday, June 16, 2009 12:06 PM Maintenance Fuel Tank Removal / Installation 13. Connect the vent and drain hoses, then connect the fuel line. Listen for a click to ensure the line is secured properly. 14. Prime the fuel pump. See page 107. 15.
Page 154: Drive Belt Condition
9922671.book Page 150 Tuesday, June 16, 2009 12:06 PM Maintenance Drive Belt Condition Replace the drive belt if it is cracked or has broken teeth or frayed edges. No matter its condition, the drive belt should be replaced at periodic intervals. See the VICTORY Service Manual or an authorized VICTORY dealer.
Page 155 9922671.book Page 151 Tuesday, June 16, 2009 12:06 PM Maintenance Drive Belt Wear Analysis Internal tooth cracks External tooth cracks: Missing teeth: Chipping (not serious): (hairline): Replace belt Replace belt OK to run, but monitor OK to run, but condition monitor condition Fuzzy edge cord: Hook wear:...
Page 156 9922671.book Page 152 Tuesday, June 16, 2009 12:06 PM Maintenance Drive Belt Tension Data Specifications are listed below for deflection and sonic tension. Sonic tension measurement requires Gates Sonic Tension Meter 507C or an equivalent. Drive Belt Deflection (Using PV-43532 Tension Gauge) Deflection Cross Roads Cross Country...
Page 157 9922671.book Page 153 Tuesday, June 16, 2009 12:06 PM Maintenance Drive Belt Tension Inspection On new drive systems or belt, adjust belt tension after the Base first 500 miles (800 km). Adjust tension at each tire change thereafter. Tip: Do not inspect or adjust drive belt tension when the belt is Belt Tension Gauge wet.
Page 158 9922671.book Page 154 Tuesday, June 16, 2009 12:06 PM Maintenance Drive Belt Tension Inspection 1. Elevate and support the motorcycle with the rear tire slightly off the floor. CAUTION! Make sure the motorcycle is stable when elevated. Injury may occur if the motorcycle tips or falls. 2.
Page 159 9922671.book Page 155 Tuesday, June 16, 2009 12:06 PM Maintenance Drive Belt Tension Inspection 6. Note the graduation mark on the rule that aligns with the lower edge of the belt. This position represents zero force. 90° Drive Belt 7. Place the support base of the tension gauge squarely against the lower surface of the belt as close as possible to the rule or tape.
Page 160 9922671.book Page 156 Tuesday, June 16, 2009 12:06 PM Maintenance Drive Belt Tension Inspection Determine The Tightest Spot ° Rear Wheel 11. Repeat the above deflection measurements with the tire’s valve stem at the rear most position, top, and front most positions (90 degrees rotation each time), recording each measurement.
Page 161 9922671.book Page 157 Tuesday, June 16, 2009 12:06 PM Maintenance Drive Belt Tension Adjustment 1. Move the wheel to the tight spot location deter- mined previously. 2. Loosen the rear axle nut on the left side. 3. Turn each axle adjuster nut clockwise an equal amount to tighten the belt (reduce deflection) or an equal amount counter-clockwise to loosen the belt (increase deflection).
Page 162 9922671.book Page 158 Tuesday, June 16, 2009 12:06 PM Maintenance Drive Belt / Rear Wheel Alignment 1. Look at the alignment reference marks on each side of the swingarm and the marks on the axle plates to verify proper wheel alignment. Axle plate mark to ref- erence mark alignment must be the same Swing Arm Axle Plate...
Page 163 9922671.book Page 159 Tuesday, June 16, 2009 12:06 PM Maintenance Drive Belt Cleaning Cleaning the drive belt will maximize belt and sprocket life and minimize drive line noise. Clean the belt at every tire change. Clean the belt more often if riding in dirty, dusty or high debris environments.
Page 164: Rear Suspension Adjustment
9922671.book Page 160 Tuesday, June 16, 2009 12:06 PM Maintenance Rear Suspension Adjustment For riding comfort and to ensure proper ground clearance, Shock Label adjust rear shock air pressure as specified on the label located in the right saddlebag cover (reproduced on page 162).
Page 165 9922671.book Page 161 Tuesday, June 16, 2009 12:06 PM Maintenance Rear Suspension Adjustment If the VICTORY air pump and gauge are not available, use the gauge provided in the tool kit, and a pressurized air source with a maximum line pressure of 72 PSI (496 kPa). After using this gauge, remove it quickly to minimize leakage.
Page 166 9922671.book Page 162 Tuesday, June 16, 2009 12:06 PM Maintenance Rear Suspension Adjustment Air Suspension Adjustment (Shock Label 7176131) Set desired pressure with bike unloaded on side stand Total Cargo & Air Pressure Total Cargo & Air Pressure Total Cargo & Air Pressure Occupant (psi)
Page 167 9922671.book Page 163 Tuesday, June 16, 2009 12:06 PM Maintenance Rear Suspension Adjustment 1. Park the motorcycle with the sidestand Air Fitting down on a firm, level surface. Remove all riders and cargo. 2. Remove the right side cover. Remove the cap from the air fitting.
Page 168 9922671.book Page 164 Tuesday, June 16, 2009 12:06 PM Maintenance Rear Suspension Adjustment 5. To reduce air pressure, push the bleed button on the gauge. Bleed pressure in small amounts until the desired pressure is attained. 6. To increase pressure, pump the handle until pressure increases to the desired amount. CAUTION! DO NOT exceed 72 PSI (496 kPa) in the shock.
Page 169 9922671.book Page 165 Tuesday, June 16, 2009 12:06 PM Maintenance Swing Arm / Rear Axle Inspection 1. Sit in the operator's seat and slowly bounce the rear suspension a few times. Make sure the suspension moves freely without binding. Listen for abnormal noises. 2.
Page 170 9922671.book Page 166 Tuesday, June 16, 2009 12:06 PM Maintenance Swing Arm / Rear Axle Inspection 5. Grasp the top or bottom surface of the tire and try to move it side to side. If there is movement at the rear axle, inspect wheel bearings and rear axle nut torque.
Page 171 9922671.book Page 167 Tuesday, June 16, 2009 12:06 PM Maintenance Front Fork / Suspension Inspection 1. Place the motorcycle on the sidestand and inspect the front forks. If fork oil is present on the outer tube, do not ride the motorcycle.
Page 172: Steering Head Inspection
9922671.book Page 168 Tuesday, June 16, 2009 12:06 PM Maintenance Steering Head Inspection 1. Elevate and support the motorcycle with the front tire slightly off the floor. CAUTION! Make sure the motorcycle is stable when elevated. Injury may occur if the motorcycle tips or falls. 2.
Page 173: Evaporative Emission Control System
9922671.book Page 169 Tuesday, June 16, 2009 12:06 PM Maintenance Fuel System Components 1. Inspect fuel hoses for cracks or damage. 2. Inspect hose connections at the fuel tank and at the fuel rail for dampness or stains from leaks. Evaporative Emission Control System (California Models) 1.
Page 174: Fast Idle
9922671.book Page 170 Tuesday, June 16, 2009 12:06 PM Maintenance Fast Idle A fast idle speed during warm up of between 1200 and 2000 RPM is automatically set by the EFI system Idle Air Control (IAC). Periodic adjustment is not required. Crankcase Breather Hose Breather Hose Inspect the crankcase breather hose for cracks or...
Page 175: Throttle Control Inspection
9922671.book Page 171 Tuesday, June 16, 2009 12:06 PM Maintenance Throttle Control Inspection 1. With the engine OFF, rotate the throttle control grip fully open and then release it. It should rotate smoothly from the rest position to the completely open position.
Page 176: Throttle Cable Freeplay
9922671.book Page 172 Tuesday, June 16, 2009 12:06 PM Maintenance Throttle Cable Freeplay Throttle freeplay is the amount of throttle control grip movement from the rest position to the point of cable resistance. Measure this distance. Freeplay should be 2-4 mm. Adjust throttle freeplay as needed. 2-4 mm to 1.
Page 177 9922671.book Page 173 Tuesday, June 16, 2009 12:06 PM Maintenance Throttle Cable Freeplay 4. Turn the adjuster on the throttle opening cable (front cable) away from the lock nut until throttle freeplay is 2-4 mm. 5. To adjust the closing cable (rear cable), hold the throttle grip lightly in the closed posi- tion.
Page 178: Throttle Cable Lubrication
9922671.book Page 174 Tuesday, June 16, 2009 12:06 PM Maintenance Throttle Cable Lubrication Lubricate control cable ends at the intervals recommended in the periodic maintenance table beginning on page 133. NOTICE: External casings are factory-lubricated. Additional lubrication could be detrimental to cable performance.
Page 179 9922671.book Page 175 Tuesday, June 16, 2009 12:06 PM Maintenance Cruise Control Cable Inspection (if equipped) 1. Remove the right side access cover. 2. Inspect the throttle body end of the cruise control cable for fraying and be sure the end is secured in the bracket.
Page 180 9922671.book Page 176 Tuesday, June 16, 2009 12:06 PM Maintenance Mechanical Clutch Lever Freeplay 1. Remove the right side access cover. 2. Hold the clutch cable and loosen the adjuster lock nut. 3. While holding the cable, turn the cable adjuster inward or outward until clutch lever freeplay is 0.5-1.5 mm.
Page 181 9922671.book Page 177 Tuesday, June 16, 2009 12:06 PM Maintenance Mechanical Clutch Lever Lubrication 1. Remove the right side access cover. Loosen the clutch Pivot Screw cable adjuster lock nut. 2. Turn the cable adjuster completely inward to provide maximum lever freeplay. 3.
Page 182 9922671.book Page 178 Tuesday, June 16, 2009 12:06 PM Maintenance Mechanical Clutch Cable Lubrication Lubricate control cable ends at the intervals recommended in the periodic maintenance table beginning on page 133. NOTICE: External casings are factory-lubricated. Additional lubrication could be detrimental to cable performance.
Page 183 9922671.book Page 179 Tuesday, June 16, 2009 12:06 PM Maintenance Front Brake Lever 1. See page 73 for front brake lever reach adjustments. 2. Lubricate the pivot bushing at the intervals recom- mended in the periodic maintenance table beginning on page 133. Also lubricate any time binding is evi- dent.
Page 184: Brake Fluid Precautions
9922671.book Page 180 Tuesday, June 16, 2009 12:06 PM Maintenance Brake Fluid Precautions WARNING Using the wrong fluid or allowing air or contaminants into the fluid system can damage the system seals or result in a malfunction that could lead to serious injury or death. Use only DOT 4 brake fluid from a sealed container.
Page 185: Rear Brake Fluid
9922671.book Page 181 Tuesday, June 16, 2009 12:06 PM Maintenance Rear Brake Fluid 1. Position the motorcycle on level ground in the fully upright position. 2. The rear brake fluid reservoir is located near the rear brake pedal, just inside the right lower leg fairing. Wipe the fluid container and the area around the reservoir cover with a clean cloth.
Page 186: Front Brake Fluid
9922671.book Page 182 Tuesday, June 16, 2009 12:06 PM Maintenance Front Brake Fluid Change the brake fluid at the intervals recommended in the periodic maintenance table beginning on page 133. Maximum Level 1. Straddle the motorcycle and bring it to the fully upright position.
Page 187 9922671.book Page 183 Tuesday, June 16, 2009 12:06 PM Maintenance Front Brake Fluid 3. To add fluid, remove the three reservoir cover screws. Remove the cover and diaphragm. Carefully add fluid to the top of the sight glass. Do not overfill. Reinstall the diaphragm, cover and screws.
Page 188 9922671.book Page 184 Tuesday, June 16, 2009 12:06 PM Maintenance Brake Disc Inspection / Cleaning 1. Inspect brake pads as outlined on page 95. 2. Inspect brake discs for nicks, scratches, cracks or other damage. Inspect the thickness of each brake disc at four or more locations around the disc.
Page 189 9922671.book Page 185 Tuesday, June 16, 2009 12:06 PM Maintenance Brake Hoses / Connections Inspect all brake hoses and connections for dampness or stains from leaking or dried fluid. Tighten any leaking connections and replace components as necessary. See the VICTORY Service Manual or your authorized VICTORY dealer.
Page 190 9922671.book Page 186 Tuesday, June 16, 2009 12:06 PM Maintenance Gear Shift Pedal 1. Inspect the shift pedal and linkage. Tighten any loose fasteners. 2. Lubricate the pivot bushing at the intervals rec- ommended in the periodic maintenance table beginning on page 133. Lubricate if a shifting problem occurs.
Page 191: Wheel Inspection
9922671.book Page 187 Tuesday, June 16, 2009 12:06 PM Maintenance Wheel Inspection Inspect both wheels for cracks or damage and replace damaged wheels promptly. Do not operate the motorcycle if wheels are damaged or cracked. See the VICTORY Service Manual or your authorized VICTORY dealer.
Page 192 9922671.book Page 188 Tuesday, June 16, 2009 12:06 PM Maintenance Tires WARNING Operating the motorcycle with improper tires or with improper or uneven tire pressure could cause loss of control or accident. Always use the correct size and type of tires specified for your vehicle. Always maintain proper tire pressure as recommended in the owner's manual and on safety labels.
Page 193 9922671.book Page 189 Tuesday, June 16, 2009 12:06 PM Maintenance Tires Tire Pressure Riding warms the tires and increases tire air pressure. For an accurate reading, check tire pressure before riding. Adjust tire pressure as recommended for the total weight of your intended load (see table).
Page 194: Spark Plugs
9922671.book Page 190 Tuesday, June 16, 2009 12:06 PM Maintenance Spark Plugs Replace spark plugs at the intervals recommended in the periodic maintenance table beginning on page 133. Always replace spark plugs in pairs. .036 inch (0.9 mm) Spark Plug Specifications Spark Plug Type NGK DCPR6E Spark Plug Gap...
Page 195 9922671.book Page 191 Tuesday, June 16, 2009 12:06 PM Maintenance Spark Plugs CAUTION! Wear eye and face protection when using pressurized air. 3. To prevent debris from entering the spark plug hole, use compressed air to clean the area around the plugs before removing them. Remove the spark plugs. Tool: 12 mm plug socket Tip: Both spark plugs should have the same light or medium tan color deposits.
Page 196 9922671.book Page 192 Tuesday, June 16, 2009 12:06 PM Maintenance Battery The motorcycle battery is a sealed, maintenance-free battery. Do not remove the battery cap strip for any reason. Keep the battery connections clean and tight at all times. WARNING Battery electrolyte is poisonous.
Page 197 9922671.book Page 193 Tuesday, June 16, 2009 12:06 PM Maintenance Battery Removal Step 1 1. Remove the two upper and two lower screws from the front chin fairing. Remove the fairing. Step 1...
Page 198: Battery Removal
9922671.book Page 194 Tuesday, June 16, 2009 12:06 PM Maintenance Battery Removal WARNING! Improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or death. When removing the battery, always disconnect the negative (black) cable first. When reinstalling the battery, always connect the negative (black) cable last. 2.
Page 199: Battery Installation
9922671.book Page 195 Tuesday, June 16, 2009 12:06 PM Maintenance Battery Installation WARNING! Improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or death. When removing the battery, always disconnect the negative (black) cable first. When reinstalling the battery, always connect the negative (black) cable last. 1.
Page 200: Battery Charging
9922671.book Page 196 Tuesday, June 16, 2009 12:06 PM Maintenance Battery Charging Tip: If your VICTORY motorcycle will not be used for a period of 6 weeks or longer, a maintenance charger should be connected to the battery. A fused maintenance charger connection is provided. The connector is designed for use with the VICTORY accessory maintenance charger available at your authorized VICTORY dealer.
Page 201 9922671.book Page 197 Tuesday, June 16, 2009 12:06 PM Maintenance Ignition Switch / Lock Lubrication Periodically lubricate the ignition switch, saddle bag locks and fuel cap lock. We recom- mend the use of VICTORY Multi-Purpose Lubricant. 1. Spray lubricant directly into the ignition switch and into each lock cylinder for 1-2 seconds.
Page 202: Sidestand Lubrication
9922671.book Page 198 Tuesday, June 16, 2009 12:06 PM Maintenance Fastener Inspection 1. Inspect the entire motorcycle chassis and engine for loose, damaged or missing fasten- ers. Tighten loose fasteners to the proper torque. Tip: Refer to the specifications section of this manual or the service manual for fastener torque values, or see your VICTORY dealer.
Page 203: Side Covers
9922671.book Page 199 Tuesday, June 16, 2009 12:06 PM Maintenance Side Covers Remove the left side cover to access the electronic con- Grommets trol module, diagnostic connector and chassis-to-engine harness connector. Remove the right side cover to access the fuses, rear suspension air fitting, clutch cable adjuster, purge valve and flasher unit.
Page 204 9922671.book Page 200 Tuesday, June 16, 2009 12:06 PM Maintenance Seat Removal / Installation 1. Remove the side covers. See page 199. Seat Screws 10 ft-lbs (13.5 Nm) 2. Remove the two seat screws. Tool: 6 mm Allen wrench 3. Lift the front of the seat upward and pull for- ward to disengage the tab at the rear of the seat.
Page 205: Headlight Aim Inspection
9922671.book Page 201 Tuesday, June 16, 2009 12:06 PM Maintenance Headlight Aim Inspection The top edge of the high beam must be 3 inches (7.6 cm) below the widest part of the head- light and centered straight ahead at 25 feet (7.6 m). Cross Roads (High Beam) Cross Country (High Beam) 25 ft.
Page 206 9922671.book Page 202 Tuesday, June 16, 2009 12:06 PM Maintenance Headlight Aim Inspection 1. Verify that tire pressure is at specification. See page 189. 2. Verify that rear suspension ride height (preload) is at specification. See page 160. 3. Position the motorcycle on a level surface with the headlight 25 feet (7.6 m) from a wall. 4.
Page 207 9922671.book Page 203 Tuesday, June 16, 2009 12:06 PM Maintenance Headlight Aim Adjustment (Cross Roads) 1. To adjust the headlamp, loosen the adjustment nut. Adjust the headlamp vertically or horizontally. 2. Hold the headlamp firmly in position while tightening the nut. Torque: 28 ft-lbs (38 Nm) 3.
Page 208 9922671.book Page 204 Tuesday, June 16, 2009 12:06 PM Maintenance Headlight Aim Adjustment (Cross Country) 1. To adjust the headlamp vertically, remove the headlight bezel by pulling straight outward at the edges to release the spring clips. Loosen the adjustment screws evenly to adjust the beam downward.
Page 209: Headlight Lamp Replacement
9922671.book Page 205 Tuesday, June 16, 2009 12:06 PM Maintenance Headlight Lamp Replacement High Intensity Discharge (HID) Lamps (Cross Country) High intensity discharge lamps should be handled only by a trained technician wearing the appropriate protective gear. See the VICTORY Service Manual or an authorized VICTORY dealer.
Page 210: Fuse Replacement
9922671.book Page 206 Tuesday, June 16, 2009 12:06 PM Maintenance Fuse Replacement NOTICE: Use fuses with the recommended amperage to avoid damage to the electrical system. Fuse Recommendations Fuse Application Fuse Size Engine 15 amp Fuel Pump/Ignition Coil 15 amp Lights 20 amp Turn Signals/Horn...
Page 211 9922671.book Page 207 Tuesday, June 16, 2009 12:06 PM Maintenance Fuse Replacement Fuse Box Tip: Use the fuse puller provided in the tool kit to remove a fuse. 1. Remove the right side cover. 2. Lift the release tab and slide the fuse box upward to remove it from the bracket.
Page 212: Electrical Precautions
9922671.book Page 208 Tuesday, June 16, 2009 12:06 PM Maintenance Electrical Precautions Be aware of the following precautions regarding the electrical system to avoid disruption of electrical signals and possible system malfunction. • DO use ONLY genuine VICTORY parts and accessories designed for your model and fol- low the instructions provided.
Page 213 9922671.book Page 209 Tuesday, June 16, 2009 12:06 PM Maintenance Electrical Precautions DO NOT: • DO NOT splice or cut any wires. • DO NOT tap in to any power or ground on the motorcycle unless specifically directed to do so by the VICTORY instructions that come with the kit. •...
Page 214: Exhaust System Inspection
9922671.book Page 210 Tuesday, June 16, 2009 12:06 PM Maintenance Engine Compression Test An engine compression test can be performed to monitor general engine condition. See the VICTORY Service Manual or your authorized VICTORY dealer. Exhaust System Inspection Check the exhaust system for stains from leaking exhaust gasses. Replace damaged or leak- ing exhaust gaskets.
Page 215: Road Test
9922671.book Page 211 Tuesday, June 16, 2009 12:06 PM Maintenance Elevating the Motorcycle WARNING! Serious injury or death can occur if the motorcycle tips or falls. Make sure the motorcycle will not tip or fall while elevated or while on the sidestand. Some procedures require raising the motorcycle to remove weight from the component being inspected.
Page 216 9922671.book Page 212 Tuesday, June 16, 2009 12:06 PM Maintenance Fastener Torque Refer to the service manual or an authorized VICTORY dealer for procedures and fastener torques not listed in this manual. Front Fender Windshield Screws Handlebar End 8 ft-lbs (11 Nm) Switch Screws 36 in-lbs (4 Nm) Cap Screws...
Page 217: Troubleshooting
9922671.book Page 213 Tuesday, June 16, 2009 12:06 PM Maintenance Troubleshooting For your personal safety, do not attempt inspection or repairs not fully described in this rider’s manual. Contact an authorized VICTORY dealer for service if you cannot determine the cause of a problem or if the inspection / repair exceeds your mechanical ability or tool resources.
Page 218 9922671.book Page 214 Tuesday, June 16, 2009 12:06 PM Maintenance Troubleshooting Starter Motor Does Not Turn or Turns Slowly Possible Cause Possible Remedy/Action Engine Stop / Run Switch in Stop Position Place switch in RUN position. Battery Discharged Fully charge the battery. See page 196. Battery Cables Loose or Corroded Inspect battery cables.
Page 219 9922671.book Page 215 Tuesday, June 16, 2009 12:06 PM Maintenance Troubleshooting Engine Starts But Misses or Runs Poorly Tip: Turn engine OFF before inspecting any of these items. Possible Cause Possible Remedy/Action Battery Discharged Fully charge the battery. See page 196. Battery Cables Loose or Corroded Inspect battery cables and connections.
Page 220 9922671.book Page 216 Tuesday, June 16, 2009 12:06 PM Maintenance Troubleshooting Shifting Difficulties or Hard to Find Neutral Possible Cause Possible Remedy/Action Shift Linkage Bushings Dry Or Worn Lubricate shift linkage. Engine Oil Level Incorrect Or Wrong Type Inspect level and quality of oil. See page 86. Clutch Damage Replace clutch.
Page 221 9922671.book Page 217 Tuesday, June 16, 2009 12:06 PM Maintenance Troubleshooting Battery Charging Rate Low or Battery Discharges Possible Cause Possible Remedy/Action Loose/Corroded Charging Circuit Check/clean battery cable connections. Check/clean Connection charging circuit connections. See dealer. Accessory Load Exceeds Charge Rate Limit accessory operation when the engine is off.
Page 222 9922671.book Page 218 Tuesday, June 16, 2009 12:06 PM Maintenance Troubleshooting Brake Noise / Poor Brake Performance Tip: Contact a VICTORY dealer if brake performance does not return after these inspections. Possible Cause Possible Remedy/Action Dust / Dirt On Brake Disc(s) Clean disc.
Page 223 9922671.book Page 219 Tuesday, June 16, 2009 12:06 PM Maintenance Service Manual Availability Some procedures are beyond the scope of this manual. See your dealer to purchase a VIC- TORY Service Manual for your motorcycle. Some procedures provided in the Service Manual require specialized knowledge, equipment, and training.
Page 224: Cleaning And Storage
9922671.book Page 220 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage VICTORY Cleaning Products This section provides tips on the very best way to clean, polish and preserve every surface of your beautiful new VICTORY Motorcycle. We recommend the use of our new Pure VIC- TORY cleaning and polishing products and accessories, which have been specially designed to offer the best care possible for your VICTORY motorcycle.
Page 225 9922671.book Page 221 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage Washing the Motorcycle NOTICE: Do not use pressurized water to wash the motorcycle. Water may seep in and deteriorate wheel bearings, brake caliper assemblies, brake master cylinders, electrical connectors, steering head bearings, and transmission seals.
Page 226 9922671.book Page 222 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage Washing the Motorcycle 2. Rinse off as much dirt and mud as possible with water running at low pressure. Use as little water as possible when washing near the air cleaner or the exhaust pipe openings. Dry these components thoroughly before using the motorcycle.
Page 227 9922671.book Page 223 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage Washing the Motorcycle There are two totally different styles of motorcycle washing and there is a Pure VICTORY Polish product for each style. Standard “Bucket Wash” This is the conventional way to wash your motorcycle. We recommend the use of Pure VIC- TORY Bike Wash Concentrate, a concentrated gentle product formulated to clean without diminishing the life of any durable polish.
Page 228 9922671.book Page 224 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage Washing the Motorcycle Spray-Rinse-and-Ride Wash This is the new way to clean your VICTORY quickly and easily, then resume riding. Pure VICTORY Spray Rinse and Ride bike wash is safe and will not harm any surface that water won’t harm.
Page 229 9922671.book Page 225 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage Washing the Motorcycle Quick Clean-Ups For quick clean-ups between washings, or when water is not available, use Pure VICTORY Spray & Wipe Instant Detailer, a complete spray-and-wipe product designed to clean and polish all surfaces.
Page 230 9922671.book Page 226 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage Polishing the Motorcycle Polished Aluminum Care When a VICTORY is new, the polished aluminum wheels, hand levers and shifter shine like chrome. Ultraviolet (UV) rays and oxidation will cause polished aluminum to grow dull, however, if it’s not properly polished and protected.
Page 231 9922671.book Page 227 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage Polishing the Motorcycle There are now two totally different styles of polishing or protecting your paint and chrome. Standard Method of Polishing Paint and Chrome Pure VICTORY Windshield, Paint and Chrome Polish is a unique formula designed to pro- duce a glass-like shine on painted or clear-coated finishes and chrome surfaces.
Page 232 9922671.book Page 228 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage Polishing the Motorcycle Standard Method of Polishing Paint and Chrome 1. Shake the container well before using. 2. Apply with Pure VICTORY 100% Microfiber Wax Applicator in a circular motion or straight line to a clean surface.
Page 233 9922671.book Page 229 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage Polishing the Motorcycle Premium Polishing for Long-Lasting Protection This newer style of polishing paint and chrome utilizes the latest in high-quality polymer technology that provides the longest-lasting protection available in the polish industry today. Pure VICTORY Liquid Spray Wax for Windshields, Paint &...
Page 234 9922671.book Page 230 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage Polishing the Motorcycle Premium Polishing for Long-Lasting Protection 1. Shake container well before use. 2. Begin by washing and rinsing the motorcycle. 3. Spray Liquid Spray Wax on a wet or dry bike, one section at a time. (For best results, the bike’s surface should be cool.) 4.
Page 235 9922671.book Page 231 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage Leather, Rubber and Vinyl Care WARNING Never use a non-recommended protectant on seats, footrests, hand grips or tires. Slippery seats, footrests or hand grips can cause loss of control. Slippery tires can cause loss of traction and loss of control.
Page 236 9922671.book Page 232 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage Leather, Rubber and Vinyl Care This product is a true conditioner, not a coating. It does not close the pores of the surfaces but penetrates, nourishes and softens the material. It protects against ultra violet (UV) rays and cracking, repels water and prolongs the life and like-new appearance of the materials.
Page 237 9922671.book Page 233 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage If you will not operate the motorcycle for several months, such as during the winter, store the motorcycle to prevent damage to the fuel system and the battery and to protect components from corrosion or deterioration.
Page 238: Clean And Protect The Motorcycle
9922671.book Page 234 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage Clean and Protect the Motorcycle To prepare the motorcycle for storage, begin by cleaning it as outlined beginning on. Wax painted surfaces and polish chromed and other metal surfaces. Apply protectant to exposed rubber, vinyl, and plastic parts.
Page 239: Engine Protection
9922671.book Page 235 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage Engine Protection Change the engine oil. See page 142. Carbon deposits and combustion acids, normally sus- pended in the engine oil when in service, settle on internal engine components during stor- age.
Page 240: Park And Cover The Motorcycle
9922671.book Page 236 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage Park and Cover the Motorcycle Park the motorcycle in its storage location. Cover it with a genuine VICTORY motorcycle cover, or a cover made from a durable, breathable material designed for storage. Covering the motorcycle helps protect it from dust and other airborne materials.
Page 241: Removal From Storage
9922671.book Page 237 Tuesday, June 16, 2009 12:06 PM Cleaning and Storage Removal From Storage 1. Remove the cover and unlock the front 5. Inspect the storage area for signs of forks (if locked). fluid leaks. Identify and perform service to any leaking components.
Page 242: Warranty
9922671.book Page 238 Tuesday, June 16, 2009 12:06 PM Warranty Motorcycle Noise Regulation Tampering with noise control systems is prohibited. Federal law prohibits the following acts or causing thereof: • The removal or rendering inoperative by any person other than for the purposes of maintenance, repair, or replacement, of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or deliv- ery to the ultimate purchaser or while it is in use, or •...
Page 243: Emissions Control System Warranty
9922671.book Page 239 Tuesday, June 16, 2009 12:06 PM Warranty Emissions Control System Warranty VICTORY MOTORCYCLES, Polaris Sales Inc. - Emission Control System Warranty Statement Your Warranty Rights and Obligations The California Air Resources Board and VICTORY Motorcycle Division, Polaris Sales Inc. (hereinafter VICTORY) are pleased to explain the emission control system warranty on your 2007 or later VICTORY motorcycle.
Page 244 9922671.book Page 240 Tuesday, June 16, 2009 12:06 PM Warranty Emissions Control System Warranty Owner’s Warranty Responsibilities As the motorcycle owner, you are responsible for the performance of the required maintenance listed in your Rider’s manual. VICTORY recommends that you retain all receipts covering maintenance on your motorcycle, but VICTORY cannot deny war- ranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.
Page 245 9922671.book Page 241 Tuesday, June 16, 2009 12:06 PM Warranty Emissions Control System Warranty VICTORY Motorcycle Division, Polaris Sales Inc. - Limited Warranty on Emission Control System VICTORY Motorcycle Division, Polaris Sales Inc., (hereinafter VICTORY) warrants that each new 2009 and later VICTORY Motorcycle that includes as standard equipment a headlight, taillight and stoplight, and is street legal: A.
Page 246 9922671.book Page 242 Tuesday, June 16, 2009 12:06 PM Warranty Emissions Control System Warranty l. Coverage Warranty defects shall be remedied during customary business hours at any authorized VICTORY motorcycle dealer located within the United States of America in compliance with the Clean Air Act and applicable regulations of the United States Envi- ronmental Protection Agency and the California Air Resources Board.
Page 247 9922671.book Page 243 Tuesday, June 16, 2009 12:06 PM Warranty Emissions Control System Warranty ll. Limitations The Emission Control System Warranty shall not cover any of the following: A. Repair or replacement required as a result of: • Accident • Misuse •...
Page 248 9922671.book Page 244 Tuesday, June 16, 2009 12:06 PM Warranty Emissions Control System Warranty lll. Limited Liability A. The liability of VICTORY under this Emission Control System Warranty is limited solely to the remedying of defects in material or workmanship by an authorized VICTORY motorcycle dealer at its place of business during customary business hours.
Page 249 9922671.book Page 245 Tuesday, June 16, 2009 12:06 PM Warranty Emissions Control System Warranty lV. Legal Rights THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. V. This warranty is in addition to the VICTORY Limited Motorcycle Warranty Vl.
Page 250: Victory Motorcycle Warranty Policy
Registration Form will be the warranty entitlement. If you have not signed the original registration and received the “cus- tomer copy”, please contact your dealer immediately. NO WARRANTY COVERAGE WILL BE ALLOWED UNLESS YOUR VICTORY MOTORCYCLE IS REGISTERED WITH VICTORY MOTORCYCLES DIVISION OF POLARIS SALES INC.
Page 251 WARRANTY ARE THE ONLY REMEDIES AVAILABLE TO ANY PERSON FOR BREACH OF THIS WARRANTY. VICTORY MOTORCYCLES DIVISION OF POLARIS SALES INC. SHALL HAVE NO LIABILITY TO ANY PERSON FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY DESCRIPTION, WHETHER ARISING OUT OF EXPRESS OR IMPLIED WARRANTY OR ANY OTHER CONTRACT, NEGLIGENCE, OR OTHER TORT OR OTH- ERWISE.
Page 252 ABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO THE ABOVE ONE YEAR WARRANTY PERIOD. VICTORY MOTORCYCLES DIVISION OF POLARIS SALES INC. FURTHER DIS- CLAIMS ALL EXPRESS WARRANTIES NOT STATED IN THIS WARRANTY OTHER THAN EMISSIONS AND EXCISE WARRANTIES.
Page 253: Specifications
9922671.book Page 249 Tuesday, June 16, 2009 12:06 PM Specifications Cross Roads Cross Country Dimensions (Dimensions and specifications may vary with features, options and accessories) Overall Length 104.4 in. (265 cm) 104.4 in. (265 cm) Overall Width 36 in. (91.4 cm) 39.2 in.
Page 254 9922671.book Page 250 Tuesday, June 16, 2009 12:06 PM Specifications Cross Roads / Cross Country Capacities Engine Oil 5 qt. (4.75 l) Approximately 4.5 qt. (4.25 l) at oil change Fuel 5.8 gal. (22 l) Fuel Reserve 1.0 gal. (3.8 l) Engine Engine Type ®...
Page 255 9922671.book Page 251 Tuesday, June 16, 2009 12:06 PM Specifications Cross Roads / Cross Country Chassis Front Suspension Type / Travel Telescopic Fork / 5.1 in. (13 cm) Front Fork Tube Diameter 43 mm Rear Suspension Type / Travel Single Monotube Air Adjustable Shock: 4.7 in. (12 cm) Swingarm Cast Aluminum with Constant Rate Linkage Front Brakes...
Page 256 9922671.book Page 252 Tuesday, June 16, 2009 12:06 PM Specifications Cross Roads / Cross Country Drive System Gear Shift Pattern 1 Down 5 Up Internal Gear Ratios 3.15:1 2.03:1 1.53: 1.24:1 6th (Overdrive) .84:1 Final Drive Ratio 2.12:1 Clutch Type Wet, Multi Plate, Diaphragm Spring...
Page 257 9922671.book Page 253 Tuesday, June 16, 2009 12:06 PM Specifications Cross Roads / Cross Country Wheels And Tires Front Wheel Type / Size Cast or Billet 18 x 3.0 inch Front Tire Type / Size DUNLOP Elite 3 - 130/70R18 63H Radial Rear Wheel Type / Size Cast or Billet 16 x 5.0 inch Rear Tire Type / Size...
Page 258 9922671.book Page 254 Tuesday, June 16, 2009 12:06 PM Specifications Cross Roads / Cross Country Fuses / Circuit Breakers Engine Fuel Pump/Ignition Coil Lights Turn Signals/Horn Ignition Chassis...
Page 259: Fuel Recommendation
9922671.book Page 255 Tuesday, June 16, 2009 12:06 PM Specifications Fuel Recommendation For best performance, use only unleaded gasoline with a 91 pump octane minimum (R+M/2 Method). DO NOT USE E-85 GASOLINE OR GASOLINE CONTAINING METHANOL. Using E85 or gasoline / methanol blends can result in poor starting and driveability, and may dam- age critical fuel system components.
Page 260: Audio System
9922671.book Page 256 Tuesday, June 16, 2009 12:06 PM Audio System Overview Audio System Introduction Radio Frequencies North America Not all motorcycles are equipped with all components discussed in the audio section • AM 520 to 1720 kHz of this manual. Components not installed at •...
Page 261: Audio Controls
9922671.book Page 257 Tuesday, June 16, 2009 12:06 PM Audio System Overview Audio Controls Operation of the audio controls is outlined in greater detail on the following pages. U.S.A. Sources Mode Menu Options • FM • AM • Bass • CB Local/Distant •...
Page 262 9922671.book Page 258 Tuesday, June 16, 2009 12:06 PM Audio System Overview Audio Controls 1. Mode Button: Press and hold the MODE button until the system enters the audio system mode menus. Then press and release the MODE button until the desired mode menu displays. Tip: Some mode menu options have sub-menus.
Page 263 9922671.book Page 259 Tuesday, June 16, 2009 12:06 PM Audio System Overview Audio Controls 3. Volume Button: Press VOL (+) to turn 4. Memory Preset (PRE) Button: Press the audio system on. Press VOL (+) to PRE to cycle through the stored preset increase audio volume.
Page 264 9922671.book Page 260 Tuesday, June 16, 2009 12:06 PM Audio System Overview Citizens Band (CB) Radio Controls If equipped, the operator’s CB radio controls are located on the left handlebar above the audio controls. Operation of these controls is outlined in greater detail on the following pages.
Page 265 9922671.book Page 261 Tuesday, June 16, 2009 12:06 PM Audio System Overview Citizens Band (CB) Radio Controls Passenger CB Controls The passenger’s radio controls are located on the headset cord. 1. Push-to-Talk (PTT): Press and hold the button to transmit. 2.
Page 266: System Operation
9922671.book Page 262 Tuesday, June 16, 2009 12:06 PM Audio System Operation Audio System Power The ignition key must be in the ACC or ON Tip: To prevent battery drain, do not leave the key in the ACC position for long periods. position to use the audio system.
Page 267 9922671.book Page 263 Tuesday, June 16, 2009 12:06 PM Audio System Operation Audio System Power Audio Volume Control The driver can adjust volume for the speak- 1. Current audio source: ers and turn the speakers off or on. • (U.S.) FM / AM / WX / iPod - AUX / XM Audio Volume •...
Page 268 9922671.book Page 264 Tuesday, June 16, 2009 12:06 PM Audio System Operation Selecting Audio Sources Press and release AM source active: the MODE button U.S. models only until the desired source is active. 1130 FM source active: WX (Weather) source active: U.S.
Page 269 9922671.book Page 265 Tuesday, June 16, 2009 12:06 PM Audio System Operation Selecting Audio Sources NAV MP3 source active: AUX source active: U.S. / European models U.S. / European models NAV MP3 iPod source active: XM Radio source active: U.S. / European models (skipped if not equipped) U.S.
Page 270 9922671.book Page 266 Tuesday, June 16, 2009 12:06 PM Audio System Operation Selecting Audio Sources Audio Tuning MW (Medium Wave) Source: Use the tuner on the European models only left control to select radio stations. Press and release TUNE (+) or TUNE (-) to locate stations in single-step increments.
Page 271 9922671.book Page 267 Tuesday, June 16, 2009 12:06 PM Audio System Operation Memory Presets The audio system features 15 user-defined presets for storing favorite stations. 1. To set a preset, 4. Press TUNE (+) or TUNE (-) to cycle to press and an available preset location.
Page 272 9922671.book Page 268 Tuesday, June 16, 2009 12:06 PM Audio System Operation Memory Presets 5. When the desired location is displayed, 6. Wait 5 seconds or push VOL (+) or press and hold the PRE button to store VOL (-) to exit. the selected radio station.
Page 273 9922671.book Page 269 Tuesday, June 16, 2009 12:06 PM Audio System Operation Audio Mode Menus Entering Mode Menus Exiting Mode Menus Press and hold the Exit the screen and return to the default dis- MODE button until play in one of two ways. the system enters 1.
Page 274 9922671.book Page 270 Tuesday, June 16, 2009 12:06 PM Audio System Operation Audio Mode Menus To change mode settings, enter the mode menu. Press TUNE (+) or TUNE (-) to change set- tings. Wait 5 seconds or push VOL (+) or VOL (-) to exit. Bass Setting Treble Setting Press TUNE (+) or TUNE (-) to adjust.
Page 275 9922671.book Page 271 Tuesday, June 16, 2009 12:06 PM Audio System Operation Audio Mode Menus To change mode settings, enter the mode menu. Press TUNE (+) or TUNE (-) to change set- tings. Wait 5 seconds or push VOL (+) or VOL (-) to exit. Fader Setting External Speakers Press TUNE (+) or TUNE (-) to adjust.
Page 276 9922671.book Page 272 Tuesday, June 16, 2009 12:06 PM Audio System Operation Audio Mode Menus To change mode settings, enter the mode menu. Press TUNE (+) or TUNE (-) to change settings. Wait 5 sec- AUTO VOL CONTROL onds or push VOL (+) or VOL (-) to exit. TUNE Automatic Volume Control (AVC) When set, this feature will lower or raise the speaker/...
Page 277 9922671.book Page 273 Tuesday, June 16, 2009 12:06 PM Audio System Operation Audio Mode Menus CB Headset Volume Controls (if equipped) The headsets have three separate volume settings: Intercom (ICOM) volume, CB receive volume and entertainment (ENT) volume. Always position headsets with the speakers directly over your ears to ensure the best sound quality and volume.
Page 278 9922671.book Page 274 Tuesday, June 16, 2009 12:06 PM Audio System Operation Audio Mode Menus CB Headset ENT Mode (if equipped) To change mode settings, enter the mode menu. Press TUNE (+) or TUNE (-) to change set- tings. OFF: Only communications are audible in the headsets. Riders can listen to navigation commands and HEADSET ENT MODE TUNE...
Page 279 9922671.book Page 275 Tuesday, June 16, 2009 12:06 PM Audio System Operation Audio Mode Menus To change mode settings, enter the mode menu. Press TUNE (+) or TUNE (-) to change set- tings. Tip: Sources and menu options will be displayed CB LO/DX Mode only for installed components.
Page 280 9922671.book Page 276 Tuesday, June 16, 2009 12:06 PM Audio System Operation Audio Mode Menus To change mode settings, enter the mode AUX Mode menu. Press TUNE (+) or TUNE (-) to Press TUNE (+) AUX MODE change settings. or TUNE (-) to TUNE choose AUX Radio Data System (RDS)
Page 281 9922671.book Page 277 Tuesday, June 16, 2009 12:06 PM Audio System Operation Audio Mode Menus XM Category Press TUNE (+) To change mode settings, enter the mode XM CATEGORY or TUNE (-) to menu. Press TUNE (+) or TUNE (-) to TUNE All Channels set the music...
Page 282 9922671.book Page 278 Tuesday, June 16, 2009 12:06 PM Audio System Operation Weather Band (WX) Weather band channels are broadcast by the Press TUNE (+) or TUNE (-) to access a National Oceanic and Atmospheric Admin- channel. istration (NOAA). NOAA operates more WX Channels than 940 transmitters covering the United WX Ch.
Page 283: Cb Radio / Intercom (Icom)
9922671.book Page 279 Tuesday, June 16, 2009 12:06 PM CB Radio / ICOM System CB/ICOM Introduction In the U.S.A., refer to the Federal Commu- Headset Use nications Commission (FCC) Plain Rules The use of helmet-mounted headsets may be pamphlet accompanying this rider’s manual restricted or prohibited in some areas.
Page 284 9922671.book Page 280 Tuesday, June 16, 2009 12:06 PM CB Radio / ICOM System Getting Started The ignition key must be in the ACC or ON Tip: To minimize distractions while riding, always make adjustments to the CB/ICOM system position to use the audio system. prior to operating your motorcycle.
Page 285 9922671.book Page 281 Tuesday, June 16, 2009 12:06 PM CB Radio / ICOM System CB Channels When the CB radio system is active, “CB” Push COM or ICOM to change channels. and the active channel will display. CHANNEL ADJUST CB 19 ICOM ICOM 100.5...
Page 286 9922671.book Page 282 Tuesday, June 16, 2009 12:06 PM CB Radio / ICOM System Push-to-Talk (PTT) Press and hold the top “TX” will display on the console screen or bottom of the PTT when one of the PTT buttons is pressed. button to transmit over “RX”...
Page 287 9922671.book Page 283 Tuesday, June 16, 2009 12:06 PM CB Radio / ICOM System Squelch Squelch blocks When squelch is set to OPEN, no filtering undesired signals and occurs. Setting squelch to CLOSED blocks noise by allowing the all signals, including strong signals. reception of signals To set the squelch level, first lower the only over a specified...
Page 288 9922671.book Page 284 Tuesday, June 16, 2009 12:06 PM CB Radio / ICOM System Driver CB Radio Volume Passenger CB Radio Volume To change settings, enter the mode menu. The passenger can control Press TUNE (+) or TUNE (-) to adjust rear headset volume when settings.
Page 289 9922671.book Page 285 Tuesday, June 16, 2009 12:06 PM CB Radio / ICOM System Local/Distant CB Radio Mode To change mode settings, enter the mode Distant: Use this setting for weaker signals. menu. Press TUNE (+) or TUNE (-) to set Receiver sensitivity will be increased.
Page 290 9922671.book Page 286 Tuesday, June 16, 2009 12:06 PM CB Radio / ICOM System CB Radio Frequencies The FCC has designated 40 citizen band (CB) channels for consumer use. Channel 9 is des- ignated as an EMERGENCY channel for emergency use only. CB Channels / Frequencies Freq.
Page 291 9922671.book Page 287 Tuesday, June 16, 2009 12:06 PM CB Radio / ICOM System ICOM System Press and release VOX Break Setting ICOM on the left The intercom is opened and closed using a control to activate voice-operated switch (VOX). The volume the intercom sys- sensitivity level required to open the inter- tem.
Page 292 9922671.book Page 288 Tuesday, June 16, 2009 12:06 PM CB Radio / ICOM System ICOM System VOX Break Setting Push COM or ICOM to adjust the sensitiv- “VOX” will display on the console screen ity setting. whenever the driver or passenger are com- municating over the intercom system.
Page 293: Headset Receptacles
9922671.book Page 289 Tuesday, June 16, 2009 12:06 PM CB Radio / ICOM System ICOM System Headset Receptacles Driver ICOM Volume The driver's headset receptacle is located on To change settings, enter the mode menu. the left side of the motorcycle below the Press TUNE (+) or TUNE (-) to adjust fuel tank.
Page 294: Aux / Ipod
9922671.book Page 290 Tuesday, June 16, 2009 12:06 PM AUX / iPod Getting Started The ignition key must be in the ACC or ON Press VOL (+) to turn the audio system on. position to use the audio system. Press and release the MODE button until AUX or iPod is active.
Page 295 9922671.book Page 291 Tuesday, June 16, 2009 12:06 PM AUX / iPod Getting Started When AUX is active, the console screen To change the mode, press the MODE button will display “AUX” as the active source. repeatedly to toggle to the AUX mode. Press TUNE (+) or TUNE (-) to set the mode to AUX (for iPod or any other MP3 ICOM...
Page 296 9922671.book Page 292 Tuesday, June 16, 2009 12:06 PM AUX / iPod iPod Song Control Press and release TUNE (+) or TUNE (-) to A quick double press and release of TUNE change the tracks in the currently selected (+) or TUNE (-) will bring up a list of songs playlist.
Page 297: Ipod Playlists
9922671.book Page 293 Tuesday, June 16, 2009 12:06 PM AUX / iPod iPod Playlists To browse tracks by artist, playlist or album, Press TUNE (+) or TUNE (-) to make a press and hold the PRE button to bring up selection.
Page 298 9922671.book Page 294 Tuesday, June 16, 2009 12:06 PM AUX / iPod iPod Tuning Press TUNE (+) or TUNE (-) once to move Tip: To exit the screen without changing tracks, press and release the MODE button. one track forward or backward. Press and hold the button to advance fast-forward or Track 1 fast-reverse.
Page 299: Xm Radio
9922671.book Page 295 Tuesday, June 16, 2009 12:06 PM XM Radio About XM Radio XM is North America’s number one satellite radio company, offering an extraordinary vari- ety of commercial-free music, plus the best in premier sports, news, talk radio, comedy, chil- dren’s and entertainment programming, broadcast in superior digital audio quality coast to coast.
Page 300: Xm Ready Legal
9922671.book Page 296 Tuesday, June 16, 2009 12:06 PM XM Radio XM Ready Legal ® XM monthly service subscription sold separately. XM Mini-Tuner and Home Dock required (each sold separately) to receive XM service. It is prohibited to copy, decompile, disassem- ble, reverse engineer, hack, manipulate or otherwise make available any technology or soft- ware incorporated in receivers compatible with the XM satellite Radio System.
Page 301: Xm Ready Subscription
9922671.book Page 297 Tuesday, June 16, 2009 12:06 PM XM Radio XM Ready Subscription Once you have installed the XM Mini- Record the Radio ID below for reference. Tuner Home Dock, inserted the XM Mini- Tip: The XM Radio ID does not use the letters “I”, Tuner, connected the XM Mini-Tuner “O”, “S”...
Page 302 9922671.book Page 298 Tuesday, June 16, 2009 12:06 PM XM Radio XM Ready Subscription Activate your XM Satellite Radio service in the U.S. online at http://activate.xmradio.com or call 1-800-XMRADIO (1-800-967-2346). Activate your XM Satellite Radio service in Can- ada online at https://activate.xmradio.ca or call 1-877-GET-XMSR (1-877-438-9677). You will need a major credit card.
Page 303 9922671.book Page 299 Tuesday, June 16, 2009 12:06 PM XM Radio Getting Started The ignition key must be in the ACC or ON When the XM radio is active, the console position to use the audio system. screen will display radio channel, preset number (if applicable), channel name or cat- Tip: To prevent battery drain, do not leave the egory, artist, and song title.
Page 304: Xm Radio Reception
9922671.book Page 300 Tuesday, June 16, 2009 12:06 PM XM Radio XM Radio Reception XM Radio Menu Options If the XM radio system is not receiving a The XM radio system has unique menus signal due to being indoors (or any overhead that apply only to this system when the XM obstruction), “No Signl”...
Page 305 9922671.book Page 301 Tuesday, June 16, 2009 12:06 PM XM Radio XM Radio Settings To access the menus, turn the audio system In the CATEGORY mode, the category of a power on and change the active source to selected station will display in the upper XM Radio.
Page 306: Xm Radio Categories
9922671.book Page 302 Tuesday, June 16, 2009 12:06 PM XM Radio XM Radio Categories XM Radio Channels With XM as the active source, use the Press TUNE (+) or TUNE (-) on the left MODE button to scroll to the XM Category control to change the channel.
Page 307: Nav Mp3
9922671.book Page 303 Tuesday, June 16, 2009 12:06 PM NAV MP3 Navigation MP3 Introduction Please read this manual and the GARMIN The audio integration kit must be installed ZUMO 660 NAV MP3 information pro- to enable outputs from the NAV MP3 (such vided with your player to become familiar as navigation instructions or user-loaded with all unit features and operation.
Page 308 9922671.book Page 304 Tuesday, June 16, 2009 12:06 PM NAV MP3 Navigation MP3 Operation Tips • Signals coming from the NAV MP3 unit will • Pause or stop the MP3 player to switch to override any source of the motorcycle’s audio radio.
Page 309 9922671.book Page 305 Tuesday, June 16, 2009 12:06 PM NAV MP3 Changing to NAV MP3 Mode The ignition key must be in the ACC or ON To change the mode, press the MODE button position to use the audio system. repeatedly to toggle to the AUX mode.
Page 310: Index
9922671.book Page 306 Tuesday, June 16, 2009 12:06 PM Index Accelerating......114 Battery Accessories, How to Choose .
Page 311 9922671.book Page 307 Tuesday, June 16, 2009 12:06 PM Index Brakes Cargo Distribution..... . . 20-21 Brake Fluid Precautions ....180 Cargo Safety .
Page 312 9922671.book Page 308 Tuesday, June 16, 2009 12:06 PM Index Clutch Lever ......70 Drive Belt Clutch Lever Freeplay, Mechanical.
Page 313 9922671.book Page 309 Tuesday, June 16, 2009 12:06 PM Index Engine, Starting ..... . 108-109 Fork Inspection ......167 Engine, Stopping.
Page 314 9922671.book Page 310 Tuesday, June 16, 2009 12:06 PM Index Halogen Lamps (Cross Roads) ....205 Ignition Switch......42-43 Hand Grip Heater Switch.
Page 315 9922671.book Page 311 Tuesday, June 16, 2009 12:06 PM Index Labels, Information......34 Major Maintenance ......131 Labels, Safety .
Page 316 9922671.book Page 312 Tuesday, June 16, 2009 12:06 PM Index Parking........123 Radio Frequencies .
Page 317 9922671.book Page 313 Tuesday, June 16, 2009 12:06 PM Index Safety Labels......34 Squelch .
Page 318 9922671.book Page 314 Tuesday, June 16, 2009 12:06 PM Index Suspension Inspection, Front..98, 165-167 Switches, Console (Cross Country) ..62-63 Suspension Inspection, Rear ....99 Switches, Left Handlebar.
Page 319 9922671.book Page 315 Tuesday, June 16, 2009 12:06 PM Index Tires VICTORY Cleaning Products....220 Condition ......188 Volt Meter .

This manual is also suitable for:

2010 victory cross country

Victory Motorcycles 2010 Victory Cross Roads Rider's Manual

Table of Contents

Identification

Quick Links

Chapters

Related Manuals for Victory Motorcycles 2010 Victory Cross Roads

Summary of Contents for Victory Motorcycles 2010 Victory Cross Roads

This manual is also suitable for:

Table of Contents