Summary of Contents for Victory Motorcycles Cross Country 2015
Page 1
2015 Rider’s Manual Cross Country® Cross Country 8-Ball™ Cross Country Tour® Cross Country® Magnum™...
Page 2
California Proposition 65 Warning This product contains or emits chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.
Page 3
® 2015 Victory Rider’s Manual Cross Country ® Cross Country 8-Ball™ Cross Country Tour ® Cross Country ® Magnum™...
Page 4
All reference to RIGHT, LEFT, FRONT, REAR are from the operator’s perspective seated in a normal riding position. Features of VICTORY Motorcycles are covered by U.S. Patent Nos: 6,976,691; 6,407,663; D489670; D482311; D482304; D481980; D481973; D474142. The following are trademarks of Polaris Industries Inc.: POLARIS®, FREEDOM®, VICTORY®, VICTORY MOTORCYCLES®...
Page 5
WARNING Improper vehicle use can result in SEVERE INJURY or DEATH. NEVER Operate: • If you are under the age of 16 and without a driver’s license with motorcycle endorsement • Under the influence of drugs or alcohol • Off-road •...
VIC- TORY dealer. To locate the nearest authorized VICTORY dealer, call 1-800-POLARIS or visit www.polaris.com. VICTORY motorcycles comply with all federal, state and local safety and emission regula- tions for the area of intended sale.
Safety About the Rider's Manual WARNING Failure to follow recommended precautions and procedures could result in severe injury or death. Always heed all safety precautions and follow all operation, inspection and maintenance procedures outlined in this manual. This rider’s manual contains information that is essential to safe riding and proper mainte- nance of your VICTORY motorcycle.
42. Failure to do so can result in serious engine damage. • Some VICTORY motorcycles include saddlebags, a windshield, a trunk, luggage racks or a passenger backrest as standard equipment. To maintain stability, be prepared to reduce...
Page 11
Safety Safe Riding Practices Follow these general safe riding practices: • Before each ride, perform the pre-ride inspections as outlined beginning on page 34. Failure to do so may result in damage to the motorcycle or an accident. • Until you're thoroughly familiar with the motorcycle and all of its controls, practice riding where there is little or no traffic.
Safety Safe Riding Practices • Reduce speed when: • the road has potholes, or is otherwise rough or uneven. • the road contains sand, dirt, gravel or other loose substances. • the road is wet, icy or oily. • the road contains painted surfaces, manhole covers, metal grating, railway crossings or other slippery surfaces.
Page 13
Safety Safe Riding Practices Carrying a Passenger Do not carry a passenger unless the motorcycle is equipped with passenger seat and passenger footrests. To carry a passenger safely: • Do not exceed the gross vehicle weight rating (GVWR) for your motorcycle. See the manufacturer’s label (on the left side of the frame at the steering head).
Safety Use of Accessories Because VICTORY cannot test and make specific recommendations concerning every accessory or combination of accessories sold, the operator is responsible for determining that the motorcycle can be safely operated with any accessories or additional weight. Use the following guidelines when choosing and installing accessories: •...
Page 15
Safety Carrying Cargo Use the following guidelines when attaching cargo or accessories to the motorcycle. Where applicable, these guidelines also refer to the contents of any accessories. • Keep cargo and accessory weight to a minimum, and keep items as close to the motorcycle as possible to minimize a change in the motorcycle’s center of gravity.
Safety Transporting the Motorcycle If you must transport the motorcycle: To lower triple clamp (one tiedown each side) • Use a truck or trailer. Do not tow the motorcycle with another vehicle, as towing will impair the motorcycle's steering and handling. •...
Safety Safety Maintenance WARNING Failure to perform safety maintenance as recommended can result in difficult handling and loss of control, which could result in serious injury or death. Always perform the safety maintenance procedures as recommended in this manual. Perform maintenance and repairs promptly as outlined in the VICTORY Service Manual, or see your authorized VICTORY dealer for service.
Page 18
Safety Gross Vehicle Weight Rating (GVWR) WARNING! Exceeding the gross vehicle weight rating of your motorcycle can reduce stability and han- dling and could cause loss of control. NEVER exceed the GVWR of your motorcycle. The maximum load capacity of your motorcycle is the maximum weight you may add to your motorcycle without exceeding the GVWR.
Safety Safety and Information Labels Labels are model-specific and market-specific. Your motorcycle may not contain all of the labels shown. 1. Vehicle Identification Number (VIN) 2. Vehicle Emission Control Information (VECI) 3. Noise Emission Control Information (NECI) 4. Operator/Fuel Warning 5.
Identification Ignition Key Number The ignition key number is stamped on the small metal tag attached to the key ring. Remove the tag and record the number on page 106. Store the tag in a safe place. Additional keys can be copied from one of the original keys. A VICTORY key blank is required.
Instruments, Features and Controls Ignition Switch The ignition key operates the ignition switch and parking lights. The ignition switch provides electrical power to the ignition, the lighting system and all electrical switches and buttons. Before starting the engine, read the instructions for starting the engine.
Instruments, Features and Controls Instrument Cluster The instrument cluster includes the speedometer, tachometer, fuel gauge, volt meter, indica- tor lamps and multi-function display. Indicator Lamps Tachometer Speedometer Volt Meter Fuel Gauge Multi-Function Display Speedometer The speedometer displays vehicle speed in either miles per hour or kilometers per hour. Tachometer The tachometer displays engine speed in revolutions per minute (RPM).
Instruments, Features and Controls Instrument Cluster Indicator Lamps Anti-Lock High Beam Low Fuel Brake System (ABS) Left Turn Right Turn Oil Pressure Cruise Control Neutral Battery Warning Check Engine Lamp Indicates Condition Neutral This lamp illuminates when the transmission is in neutral and the ignition key is in the ON or PARK position.
Instruments, Features and Controls Instrument Cluster Multi-Function Display Use the mode button to toggle through the modes of the multi-function display. See page 27. Permanently Displayed Modes • Clock Clock • Gear Position • Ambient Temperature Gear Trip Computer Modes Position •...
Page 27
Instruments, Features and Controls Instrument Cluster Multi-Function Display Display Units (Standard/Metric) The display can be changed to display either standard or metric units of measurement. Tip: To exit the set-up mode at any time, wait 10 seconds.The display automatically exits and returns to the odometer display.
Instruments, Features and Controls Instrument Cluster Multi-Function Display Odometer/Trip Odometer The odometer displays the total distance traveled by the vehicle. The trip odometer displays distance traveled since the trip odometer was reset. To view the trip odometer, turn the key to the ON position.
Instruments, Features and Controls Left Handlebar Switches High/Low Light Switch Flasher (Hazard) Switch Turn Signal Switch Horn Button Lamp Switch Description Emergency The emergency flasher switch activates and cancels the emergency flash- Flasher Switch ers. When the emergency flashers are active, all of the turn signals flash. (Hazard Switch) Press the top of the switch to activate the emergency flashers.
Instruments, Features and Controls Right Handlebar Switches Engine Stop/Run Switch Stop The engine stop/run switch is located on the right handlebar. This switch completes or interrupts the ignition, starter and fuel pump circuits. Use the engine stop/run switch to turn the engine off quickly.
Instruments, Features and Controls Throttle Control Grip Decrease Speed The throttle control grip is located on the right handlebar. Use the throttle control grip to con- trol engine speed. While seated in the proper riding position: • Rotate the top of the grip rearward to increase engine speed and power.
Page 32
Instruments, Features and Controls Brakes Anti-Lock Brake System (ABS) (if equipped) The anti-lock brake system automatically reduces or increases brake pressure as needed to provide optimum braking control, reducing the chance of wheel lock-up during hard braking events or when braking on rough, uneven, slippery or loose surfaces. See page 10. •...
Instruments, Features and Controls Brakes The front brake lever activates the front brake calipers. The rear brake pedal activates the rear brake caliper. For maximum brake effectiveness, apply the front brake lever and the rear brake pedal together. Front Brake Lever Front Brake Lever The front brake lever is located on the right handlebar.
Instruments, Features and Controls Tilt Sensor A tilt sensor stops the engine if the motorcycle tips beyond 45 degrees to one side. The check engine light or message will also activate. To restart the engine, cycle the ignition switch to the OFF position, wait 20 seconds, then restart the engine.
Instruments, Features and Controls Fuel Cap Use the ignition key to lock and unlock the fuel cap. Always lock the fuel cap before riding. An open fuel cap could contact the handlebar. To open the fuel cap, lift the lock cover. Place the key in the lock and turn it clockwise.
Pre-Ride Inspections To keep your motorcycle in safe operating condition, always perform the recommended pre- ride inspections before each ride. This is especially important before making a long trip and when removing the motorcycle from storage. WARNING! Failure to perform the recommended pre-ride inspections could result in component failure while riding, which could result in serious injury or death.
Page 37
Pre-Ride Inspections Turn the ignition key to the ON position and move the stop/run switch to RUN before per- forming the following electrical inspections. Return the ignition key to the OFF position after completing these inspections. If inspection of any electrical item reveals component failure, repair or replace the component before operating the motorcycle.
Pre-Ride Inspections Engine Oil Level The oil fill cap/dipstick is located on the right side of the vehicle. Always use the recommended oil. See page 106. Tip: The engine must be at normal operating temperature when checking the oil level. 1.
Pre-Ride Inspections Tires Tire Pressure Check tire pressure before riding, when the tires are cold. This will provide the most accurate reading, as riding warms the tires and increases tire air pressure. Adjust tire pressure as needed based on the total weight of your intended load. See page 75. Tire Condition Inspect the tire sidewalls, road contact surface and tread base.
Pre-Ride Inspections Rear Brake Pedal 1. Press downward on the rear brake pedal. It should move freely and smoothly. It should not move more than 3/8 inch (8 mm) before resistance is firm. It should continue to feel firm, without loss of pres- sure, until the pedal is released.
Pre-Ride Inspections Brake Pads Inspect each front brake pad on both sides of Friction the front disc. Inspect each rear brake pad on Material both sides of the rear disc. When the thinnest point of the friction material has worn to the minimum recommended thickness, see your VICTORY dealer for brake pad replacement.
Pre-Ride Inspections Front Suspension Inspect the front forks for oil leaks or damage, and verify smooth suspension operation. See page 66. Steering 1. On level ground, straddle the motorcycle and bring it to the fully upright position. Turn the handlebars from stop to stop. The action should be smooth, but not loose. 2.
Page 43
Pre-Ride Inspections Sidestand 1. On level ground, straddle the motorcycle and bring it to the fully upright position. 2. Move the sidestand up to the stored position and down to the fully extended position sev- eral times. It should move smoothly and quietly. Make sure the return spring holds the sidestand tightly in place when the sidestand is in the stored position.
Operation The operation section of this manual describes how to ensure maximum performance and longevity through the proper care and operation of your motorcycle. Tip: Even if you're an experienced motorcycle operator or passenger, read all of the safety information in this manual before operating the motorcycle.
Page 45
Operation Fueling Always refuel on level ground with the sidestand down. Review the fuel warnings. See page 14. Use only the recommended fuel. See page 106. Hold the nozzle while filling. Do not rest the weight of the nozzle and hose on the filler neck. Do not leave the nozzle unattended. WARNING! Overflows or spilled gasoline could contact a hot engine or exhaust system and cause a fire, which could result in serious injury or death.
Operation Starting the Engine The starter interlock system allows the engine to be started only when the transmission is in neutral, or when the transmission is in gear with the clutch disengaged (clutch lever pulled in). Tip: If the motorcycle runs out of fuel, prime the system before attempting to restart the engine. See page 43.
Operation Shifting Gears WARNING! Forced shifting (with clutch engaged) could cause damage to the engine, transmission and drive train. Such damage could cause loss of control, which could result in serious injury or death. Always pull the clutch lever fully toward the handlebars to disengage the clutch before shifting gears. This motorcycle is equipped with a Overdrive six-speed transmission.
Page 48
Operation Shifting Gears Tip: Within the recommended speed ranges (see Recommended Shift Points table), you can downshift to slow the motorcycle or to increase power. You may want to downshift when climbing a hill or passing. Downshifting also helps to decrease speed when combined with closing the throttle. 8.
Page 49
Operation Braking Always allow sufficient stopping distance so that brakes can be applied gradually. Tip: Applying slightly more front brake than rear brake generally provides the best braking perfor- mance. 1. To slow the motorcycle with the brakes, close the throttle and apply the front and rear brakes evenly and gradually.
Page 50
Operation Using Cruise Control (if equipped) Resume Speed After disengaging the cruise control with the brake, throttle Resume or clutch, wait at least 3 seconds, then press the resume but- ton (RES) to return to the set speed. If the resume button is pressed within 3 seconds of disengag- ing, the cruise control may not engage, even if the cruise con- trol indicator illuminates.
Operation Stopping the Engine Before stopping the engine, bring the motorcycle to a complete stop. Shift to neutral or dis- engage the clutch. WARNING! Stopping the engine with the transmission in gear while the motorcycle is moving could cause loss of rear wheel traction or engine and transmission damage, which could cause loss of control and serious injury or death.
Page 52
Operation Reverse Operation (if equipped) NOTICE: Do not attempt to engage or disengage the reverse system when the motorcycle is moving. Before Operating in Reverse: • always sit on the motorcycle with legs astride and both feet on the ground. •...
Maintenance Safety During Service Procedures WARNING Failure to follow recommended precautions and procedures could result in severe injury or death. Always heed all safety precautions and follow all operation, inspection and maintenance procedures outlined in this manual. • Improperly installed or adjusted components can make the motorcycle unstable or hard to handle. Improperly installed electrical components can cause engine or electrical system failure.
Maintenance Proper maintenance assures the highest level of safety, durability and dependability for your motorcycle. • Have your VICTORY dealer perform the break-in maintenance procedures when the motorcycle’s odometer registers 500 miles (800 km). • Perform the recommended periodic maintenance at the intervals specified in the periodic maintenance table beginning on page 53.
Page 55
Maintenance Periodic Maintenance Table See table key below Odometer Reading in Miles (Kilometers) Component Page Air Filter Battery Brake Fluid Brake Pads Clutch Cable Clutch Lever 69 70 (Mechanical) Control Cables 69 70 Crankcase Vent Drive Belt Drive Belt Adjustment Adjust with each tire change thereafter Engine Oil &...
Maintenance Maintenance Log Maintenance Performed Miles / Km Notes Performed...
Page 57
Maintenance Engine Oil / Filter Change Change the engine oil at the intervals specified in the peri- odic maintenance table beginning on page 53. 1. Start the engine and allow it to idle for several min- utes. Stop the engine. Tip: The engine must be at normal operating temperature before changing the oil.
Maintenance Air Filter Inspect the air filter often if riding in unusually wet or dusty Retainer Screws conditions. Do not apply air filter oil to this air filter. The fuel line is secured to the main wiring harness with a cable tie.
Page 59
Maintenance Fuel Tank Removal 5. The fuel line is secured to the main wiring harness with a cable tie. Do not cut or remove the cable tie. Pivot the rear of the tank upward to access the tank bottom. Support the rear of the tank in this position.
Maintenance Fuel Tank Installation 1. Place the handlebars in the straight ahead position. Cover the front of the fuel tank with a protective cloth to prevent damage. Drain 2. Using care to avoid damage to the fuel tank Line fitting and special tool, position the fuel tank on the frame of the motorcycle.
Page 61
Maintenance Fuel Tank Installation 10. Install the rear isolators (with flange side toward Isolators the tank) and flange bushings. 11. Lower the tank and install the tank bolts. Torque: 18 ft-lbs (24 Nm) 12. Connect the vent line, ground wire and ground wire bolt.
Maintenance Drive Belt Condition Replace the drive belt if it is cracked or has broken teeth or frayed edges. No matter its condition, the drive belt should be replaced at periodic intervals. See the VICTORY Service Manual or an authorized VICTORY dealer. DO NOT attempt to check belt tension if the belt has been exposed to rain or washing within a 24 hour period or if the belt is hot from riding.
Page 63
Maintenance Drive Belt Tension Data Specifications are listed below for deflection and sonic tension. Sonic tension measurement requires Gates Sonic Tension Meter 507C or an equivalent. Drive Belt Deflection (Using PV-43532 Tension Gauge) Deflection CROSS COUNTRY Models 32 mm ± 0.5 mm Drive Belt Sonic Tension (Using Sonic Tension Meter) Required Data Sonic Tension...
Page 64
Maintenance Drive Belt Tension Inspection 1. Elevate and support the motorcycle with the rear tire slightly off the floor. CAUTION! Make sure the motorcycle is stable when elevated. Injury may occur if the motorcycle tips or falls. 2. Place the transmission in neutral. Drive Belt 3.
Page 65
Maintenance Drive Belt Tension Adjustment 1. Move the wheel to the tight spot location determined previously. 2. Loosen the rear axle nut on the left side. 3. Turn each axle adjuster nut clockwise an equal amount to tighten the belt (reduce deflection) or an equal amount counter- clockwise to loosen the belt (increase deflection).
Maintenance Rear Suspension Adjustment For riding comfort and to ensure proper ground Shock Label clearance, adjust rear shock air pressure as specified on the label located in the right saddlebag cover (reproduced below). Follow these guidelines when adjusting: • Park the motorcycle with the sidestand down on a firm, level surface.
Maintenance Rear Suspension Adjustment 1. Park the motorcycle with the sidestand Air Fitting down on a firm, level surface. Remove all riders and cargo. 2. Remove the right side cover. Remove the cap from the air fitting. 3. Refer to the shock label to determine the recommended air pressure.
Maintenance Front Fork / Suspension Inspection 1. Place the motorcycle on the sidestand and inspect the front forks. If fork oil is present on the outer tube, do not ride the motorcycle. See your dealer for service before operating. If fork oil is present around the fork seals or inner tubes, replace the fork seals.
Maintenance Evaporative Emission Control System (California Models) 1. Inspect all evaporative emission control system hoses and connections. Make sure all connections are tight. 2. Inspect connections at the evaporative emissions canister to be sure they are secure. The canister is located under the rear fender.
Maintenance Throttle Control Inspection 1. With the engine OFF, rotate the throttle control grip fully open and then release it. It should rotate smoothly from the rest position to the completely open position. It should return to the rest position quickly when released.
Maintenance Cruise Control Cable Inspection (if equipped) 1. Remove the right side access cover. 2. Inspect the throttle body end of the cruise control cable for fraying and be sure the end is secured in the bracket. Throttle Cable Lubrication Lubricate control cable ends at the intervals recommended in the periodic maintenance table Cruise Control Cable...
Page 72
Maintenance Mechanical Clutch Lever Lubrication 1. Remove the right side access cover. Loosen the clutch Pivot Screw cable adjuster lock nut. 2. Turn the cable adjuster completely inward to provide maximum lever freeplay. 3. Remove the clutch lever pivot nut and screw. Disconnect the clutch cable from the clutch lever.
Maintenance Rear Brake Pedal 1. See page 31 for rear brake pedal adjustments. 2. Lubricate the pivot bushing at the intervals recommended in the periodic maintenance table beginning on page 53. Also lubricate any time binding is evident. Use VICTORY All Purpose Grease or equivalent.
Maintenance Front Brake Lever 1. See page 31 for front brake lever reach adjustments. 2. Lubricate the pivot bushing at the intervals recommended in the periodic maintenance table beginning on page 53. Also lubricate any time binding is evident. Use VICTORY All Purpose Grease or equivalent.
Maintenance Brake Disc Inspection / Cleaning 1. Inspect brake pads as outlined on page 39. 2. Inspect brake discs for nicks, scratches, cracks or other damage. Inspect the thickness of each brake disc at four or more locations around the disc. If any disc is worn to the minimum thickness at the thinnest point, or if a disc is damaged, see your VICTORY dealer for replacement.
Page 76
Maintenance Anti-Lock Brake System (ABS) Tone Ring/Sensor Inspection 1. Visually inspect for damaged teeth on the front and rear ABS tone rings. Inspect for nicks and dents on the face of the teeth. The teeth edges should be consistent in appearance. If a tone ring is damaged, see your VICTORY dealer for replacement as soon as possible.
Maintenance Tires Tire Pressure Riding warms the tires and increases tire air pressure. For an accurate reading, check tire pressure before riding. Adjust tire pressure as recommended for the total weight of your intended load (see table). WARNING! Do not exceed the maximum recommended inflation pressure to seat the bead. Tire or rim failure may result.
Maintenance Battery The motorcycle battery is a sealed, maintenance-free battery. Do not remove the battery cap strip for any reason. Keep the battery connections clean and tight at all times. WARNING Battery electrolyte is poisonous. It contains sulfuric acid. Serious burns can result from contact with skin, eyes or clothing.
Maintenance Battery Installation WARNING! Improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or death. When removing the battery, always disconnect the negative (black) cable first. When reinstalling the battery, always connect the negative (black) cable last. 1.
Maintenance Handlebar Position On models equipped with two handlebar positions, the motorcycle is High manufactured with handlebars in the low position. Before changing Position handlebar position, check regulations in your area of operation. Operation with the handlebars in the high position may not be legal in all areas or for all riders.
Maintenance Side Covers Remove the left side cover to access the electronic Grommets control module, diagnostic connector and chassis-to- engine harness connector. Remove the right side cover to access the fuses, rear suspension air fitting, clutch cable adjuster, purge valve and flasher unit. Remove both side covers to access the seat screws.
Maintenance Saddlebag Bumpers Saddlebag bumpers (if equipped) can be removed. Be sure to retain the M6 screws, nut plates and spacer plates for future reinstallation. 1. Remove the saddlebags. 2. Remove the five (5) screws securing each bumper to the frame, along with the nut plate and spacer plate.
Maintenance Seat Removal / Installation 1. Remove the side covers. See page 80. Seat Screws 10 ft-lbs (13.5 Nm) 2. Remove the two seat screws. Tool: 6 mm Allen wrench 3. Lift the front of the seat upward and pull forward to disengage the tab at the rear of the seat.
Maintenance Headlight Aim Inspection (LED) For best results, have an assistant and 25 ft. (7.6 m) perform the inspection in a dimly lit area. 1. Verify that tire pressure is at specification. See page 75. 3 in. (7.6 cm) 2. Verify that rear suspension ride height (preload) is at Step 5 Step 6...
Maintenance Electrical Precautions Be aware of the following precautions regarding the electrical system to avoid disruption of electrical signals and possible system malfunction. • DO use ONLY genuine VICTORY parts and accessories designed for your model and follow the instructions provided. •...
Maintenance Elevating the Motorcycle WARNING! Serious injury or death can occur if the motorcycle tips or falls. Make sure the motorcycle will not tip or fall while elevated or while on the sidestand. Some procedures require raising the motorcycle to remove weight from the component being inspected.
Maintenance Troubleshooting For your personal safety, do not attempt inspection or repairs not fully described in this rider’s manual. Contact an authorized VICTORY dealer for service if you cannot determine the cause of a problem or if the inspection / repair exceeds your mechanical ability or tool resources.
Page 90
Maintenance Troubleshooting Shifting Difficulties or Hard to Find Neutral Possible Cause Possible Remedy/Action Shift Linkage Bushings Dry Or Worn Lubricate shift linkage. Engine Oil Level Incorrect Or Wrong Type Inspect level and quality of oil. See page 36. Clutch Damage Replace clutch.
Cleaning and Storage VICTORY Cleaning Products This section provides tips on the very best way to clean, polish and preserve every surface of your beautiful new VICTORY Motorcycle. We recommend the use of our new Pure VIC- TORY cleaning and polishing products and accessories, which have been specially designed to offer the best care possible for your VICTORY motorcycle.
Page 92
Cleaning and Storage Washing the Motorcycle There are two totally different styles of motorcycle washing and there is a Pure VICTORY Polish product for each style. Standard “Bucket Wash” This is the conventional way to wash your motorcycle. We recommend the use of Pure VIC- TORY Bike Wash Concentrate, a concentrated gentle product formulated to clean without diminishing the life of any durable polish.
Page 93
Cleaning and Storage Washing the Motorcycle Quick Clean-Ups For quick clean-ups between washings, or when water is not available, use Pure VICTORY Spray & Wipe Instant Detailer, a complete spray-and-wipe product designed to clean and polish all surfaces. It works quickly and easily and is silicone-free so it leaves no oily nor white residue.
Page 94
Cleaning and Storage Polishing the Motorcycle There are now two totally different styles of polishing or protecting your paint and chrome. Standard Method of Polishing Paint and Chrome Pure VICTORY Windshield, Paint and Chrome Polish is a unique formula designed to pro- duce a glass-like shine on painted or clear-coated finishes and chrome surfaces.
Cleaning and Storage Polishing the Motorcycle Premium Polishing for Long-Lasting Protection This newer style of polishing paint and chrome utilizes the latest in high-quality polymer technology that provides the longest-lasting protection available in the polish industry today. Pure VICTORY Liquid Spray Wax for Windshields, Paint & Chrome is formulated for pol- ishing after washing and can be sprayed on wet or dry surfaces.
Cleaning and Storage If you will not operate the motorcycle for several months, such as during the winter, store the motorcycle to prevent damage to the fuel system and the battery and to protect components from corrosion or deterioration. During storage you might use products that are potentially hazardous;...
Cleaning and Storage Engine Protection Change the engine oil. See page 55. Carbon deposits and combustion acids, normally sus- pended in the engine oil when in service, settle on internal engine components during stor- age. Settled deposits can cause engine damage or internal corrosion. Battery Care 1.
Cleaning and Storage Removal From Storage 1. Remove the cover and unlock the front forks (if locked). 2. Verify that tire pressure is at specification. 3. Install the battery and perform an electrical inspection. 4. Check the oil level. If the motorcycle was stored in an area subject to wide swings in temperature and humidity (such as outdoors), change the engine oil before starting the engine.
Victory Motorcycles Warranty Policy Limited Warranty Victory Motorcycles Division, Polaris Industries Inc., 2100 Highway 55, Medina, Minnesota 55340 gives a ONE YEAR LIMITED WARRANTY on all components of your VICTORY motorcycle against defects in material or workmanship. This warranty covers parts and labor charges for repair or replacement of defective parts and begins on the date of purchase by the original retail purchaser.
Page 100
LIMITED WARRANTY. ALL OTHER IMPLIED WARRANTIES (INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY) ARE LIMITED IN DURATION TO THE ABOVE 12 MONTH WARRANTY PERIOD. VICTORY MOTORCYCLES DISCLAIMS ALL EXPRESS WARRANTIES NOT STATED IN THIS WARRANTY. SOME STATES DO NOT PERMIT THE EXCLUSION...
Page 101
In the country where your motorcycle was purchased: Warranty or Service Bulletin repairs must be done by an authorized VICTORY MOTORCYCLES dealer. If you move or are traveling within the country where your motorcycle was purchased, Warranty and Service Bulletin repairs may be requested from any authorized VICTORY MOTORCYCLES dealer.
Otherwise, the owner may become subject to penalties under state and local ordinances. Noise Emission Warranty VICTORY MOTORCYCLES warrants that this exhaust system, at the time of sale, meets all applicable U.S. EPA Federal noise standards. This warranty extends to the first person who buys this exhaust system for purposes other than resale, and to all subsequent buyers.
Victory Motorcycle Division, Polaris Industries Inc. - Emission Control System Warranty Statement Your Warranty Rights and Obligations The California Air Resources Board and VICTORY MOTORCYCLES (hereinafter VICTORY) are pleased to explain the emission control system warranty on your 2014 or later VICTORY motorcycle. In California, new motor vehicles must be designed, built and equipped to meet the state’s stringent anti-smog standards.
Page 104
Warranties Emissions Control System Warranty I. Coverage Warranty defects shall be remedied during customary business hours at any authorized VICTORY dealer located within the United States of America in compliance with the Clean Air Act and applicable regulations of the United States Environmental Protection Agency and the California Air Resources Board.
Page 105
Such maintenance may be performed at a service establishment or by any individual. The warranty period begins on the date the motorcycle is delivered to an ultimate purchaser. VICTORY MOTORCYCLES 2100 Highway 55 Medina, MN 55340...
Specifications CROSS COUNTRY Dimensions (Dimensions and specifications may vary with features, options and accessories) Overall Length 104.3 in. (265 cm) (CC / 8-BALL) 104.6 in. (265.7 cm) (MAGNUM) 108.1 in. (274.7 cm) (TOUR) Overall Width 39.3 in. (100 cm) Overall Height 52.5 in.
Page 107
Specifications CROSS COUNTRY Chassis Front Suspension Type / Travel Telescopic Fork / 5.1 in. (13 cm) Front Fork Tube Diameter 43 mm Rear Suspension Type / Travel Single Monotube Air Adjustable Shock: 4.7 in. (12 cm) Swingarm Cast Aluminum with Constant Rate Linkage Front Brakes Dual 300 x 5 mm / Floating Rotor / 4 Piston Calipers Rear Brakes...
Specifications Fuel Recommendation For best performance, use only unleaded gasoline with a 91 pump octane minimum (R+M/2 Method). DO NOT USE E-85 GASOLINE OR GASOLINE CONTAINING METHANOL. Using E85 or gasoline / methanol blends can result in poor starting and driveability, and may damage critical fuel system components.
Cross Country/Cross Country Tour Audio System Audio System Introduction Audio Controls Please see page 126 for CROSS COUNTRY 8-BALL audio system information. Please see page 127 for CROSS COUNTRY MAGNUM audio system information. Not all motorcycles are equipped with an audio system.
Page 110
Cross Country/Cross Country Tour Audio System Citizens Band (CB) Radio Controls If equipped, the operator’s CB radio controls are located on the left handlebar above the audio controls. Operation of these controls is outlined in greater detail on the following pages.
Page 111
Cross Country/Cross Country Tour Audio System Audio System Power The ignition key must be in the ACC or ON position to use the audio system. VICTORY With the key in the ACC or ON position and audio system OFF, the screen will display “VICTORY”.
Page 112
Cross Country/Cross Country Tour Audio System Selecting Audio Sources iPod source active: Press and release the MODE button until U.S. / European models (skipped if not equipped) the desired source is iPod Artist active. Title Playlist FM source active: AUX source active: U.S.
Cross Country/Cross Country Tour Audio System Audio Tuning Memory Presets Use the tuner on the The audio system features 15 user-defined left control to select presets for storing favorite stations. radio stations. 1. To set a preset, Press and release press and TUNE (+) or TUNE release the...
Page 114
Cross Country/Cross Country Tour Audio System Audio Mode Menus Entering Mode Menus Treble Setting Press and hold the Press TUNE (+) or TUNE (-) to adjust. MODE button until the system enters TREBLE 0 the audio system TUNE mode menus. Then press and release the MODE button TREBLE +3...
Page 115
Cross Country/Cross Country Tour Audio System Audio Mode Menus To change mode settings, enter the mode menu. Press TUNE (+) or TUNE (-) to change settings. Wait 5 AUTO VOL CONTROL TUNE seconds or push VOL (+) or VOL (-) to exit. Automatic Volume Control (AVC) AUTO VOL CONTROL When set, this feature will lower or raise the speaker/...
Page 116
Cross Country/Cross Country Tour Audio System Audio Mode Menus Radio Data System (RDS) To change mode settings, enter the mode menu. Press TUNE (+) or TUNE (-) to Press TUNE (+) or TUNE (-) to turn the change settings. radio data system on or off. When on, the screen will display artist, song title, etc.
Page 117
Cross Country/Cross Country Tour Audio System Audio Mode Menus Weather Band (WX) To change mode settings, enter the mode menu. Press TUNE (+) or TUNE (-) to Weather band channels are broadcast by the change settings. National Oceanic and Atmospheric Administration (NOAA).
Page 118
Cross Country/Cross Country Tour Audio System CB Radio / ICOM System CB/ICOM Introduction CB Channels In the U.S.A., refer to the Federal When the CB radio system is active, “CB” Communications Commission (FCC) Plain and the active channel will display. Rules pamphlet accompanying this rider’s manual for a comprehensive guide of citizens band (CB) radio rules and...
Page 119
Cross Country/Cross Country Tour Audio System CB Radio / ICOM System Push-to-Talk (PTT) Squelch Press and hold the top Squelch blocks or bottom of the PTT undesired signals and button to transmit over noise by allowing the CB radio. The reception of signals passenger must push only over a specified...
Page 120
Cross Country/Cross Country Tour Audio System CB Radio / ICOM System Local/Distant CB Radio Mode To change mode settings, enter the mode menu. Press TUNE (+) or TUNE (-) to set CB LO / DX MODE the CB to local (LO) or distant (DX) mode. TUNE DISTANT Distant: Use this setting for weaker signals.
Page 121
Cross Country/Cross Country Tour Audio System CB Radio / ICOM System ICOM System Driver ICOM Volume Press and release To change settings, enter the mode menu. ICOM on the left Press TUNE (+) or TUNE (-) to adjust control to activate settings.
Cross Country/Cross Country Tour Audio System AUX / iPod Getting Started iPod Song Control The ignition key must be in the ACC or ON Press and release TUNE (+) or TUNE (-) to position to use the audio system. change the tracks in the currently selected playlist.
Page 123
Cross Country/Cross Country Tour Audio System AUX / iPod iPod Playlists iPod Tuning Press TUNE (+) or TUNE (-) once to move To browse tracks by artist, playlist or album, one track forward or backward. Press and press and hold the PRE button to bring up hold the button to advance fast-forward or the selection screen.
Page 124
Cross Country/Cross Country Tour Audio System SiriusXM Radio About SiriusXM Satellite Radio (for A Warning Against Reverse U.S.A. and Canadian Products) Engineering SiriusXM Radio offers an extraordinary It is prohibited to copy, decompile, variety of commercial-free music, plus disassemble, reverse engineer, hack, premier sports, news, talk radio, stand-up manipulate or otherwise make available any comedy, children’s and entertainment...
Page 125
Cross Country/Cross Country Tour Audio System SiriusXM Radio Getting Started SiriusXM Radio Menu Options The ignition key must be in the ACC or ON The SiriusXM radio system has unique position to use the audio system. menus that apply only to this system when the SiriusXM radio is the active source.
Page 126
Cross Country/Cross Country Tour Audio System SiriusXM Radio SiriusXM Radio Categories SiriusXM Radio Channels With SiriusXM as the active source, use the Press TUNE (+) or TUNE (-) on the left MODE button to scroll to the SiriusXM control to change the channel. Category menu.
Page 127
Cross Country/Cross Country Tour Audio System NAV MP3 Navigation MP3 Introduction Changing to NAV MP3 Mode Please read this manual and the GARMIN The ignition key must be in the ACC or ON ZUMO 660 NAV MP3 information pro- position to use the audio system. vided with your player to become familiar Press VOL (+) to turn the audio system on.
Cross Country 8-BALL Audio System Audio System Introduction Audio Controls The 8-BALL audio system differs from the system described on the preceding pages. Tip: The 8-BALL audio software cannot be updated. The 8-BALL audio system allows you to listen to audio from: •...
Cross Country MAGNUM Audio System Audio System Introduction iPod / iPhone Device Compatibility Please see page 126 for CROSS COUNTRY 8-BALL audio system information. Your radio will connect with the following Please see page 107 for CROSS COUNTRY iPod and iPhone models. Update your iPod and CROSS COUNTRY TOUR audio system and iPhone devices to the latest software information.
Page 130
Cross Country MAGNUM Audio System Audio System Introduction Radio Frequencies Radio Sources North America North America Sources • AM 520 to 1720 kHz • FM • FM 87.9 to 107.9 MHz • AM • WX 7 NOAA Channels • WX (162.400 to 162.550 MHz) •...
Cross Country MAGNUM Audio System Audio Controls Instrument Cluster Audio Display The audio controls are located on the left handlebar. USB Connector A USB connector cord is located in the right saddlebag. A pouch is provided to hold your device while operating the vehicle. The pouch is padded and tethered to the fairing to securely hold your device.
Cross Country MAGNUM Audio System Instrument Cluster Audio System Power Audio Display Zones VICTORY The LCD display uses four distinct zones to provide the rider with audio system information. Turn the power switch ON to use the audio system. Tip: To prevent battery drain when the engine is not running, power will automatically turn off after 5 minutes.
Cross Country MAGNUM Audio System Mute/Push-To-Talk (PTT) Selecting Audio Sources FM source: Press once to mute the audio system All models (shown with RBDS FULL) volume. Press to un-mute the audio system volume. AM source: Double press to activate voice All models excluding Europe recognition feature on a paired phone.
Page 134
Cross Country MAGNUM Audio System Selecting Audio Sources WX (Weather) source: Bluetooth Driver source: North America models only USB sources: All models (skipped if not enabled) Tip: Pandora® is available on some Bluetooth Flash memory connected devices. iPhone / iPod connected FM / AM / MW / LW Tuning Tip: MW and LW radio sources are in Europe only.
Page 135
Cross Country MAGNUM Audio System Selecting Audio Sources FM / AM / MW / LW Tuning Weather Band (WX) Memory Presets Weather band channels are broadcast by the The audio system features 15 user-defined National Oceanic and Atmospheric Admin- presets for each tuner source for storing istration (NOAA).
Page 136
Cross Country MAGNUM Audio System Selecting Audio Sources USB Audio Source - Flash / Memory USB Audio Source - iPod / iPhone Stick Connected Connect the USB memory stick to the USB 1. Connect a compatible iPod or iPhone connector cable. The following music files device to the USB connector cable.
Page 137
Cross Country MAGNUM Audio System Selecting Audio Sources USB Audio Source - iPod / iPhone USB Audio Source - iPod / iPhone Connected with Pandora ® Category Select When using the Pandora app on an iPod or iPhone, connect the device to the USB connector.
Page 138
Cross Country MAGNUM Audio System Selecting Audio Sources USB Audio Source - iPod / iPhone with Pandora ® 4. To give a “THUMBS DOWN” for the 7. When the default screen displays, press current song, Press and hold and release to display the station list screen.
Page 139
Cross Country MAGNUM Audio System Selecting Audio Sources NAV Audio Source Navigation MP3 Operation Tips • Signals coming from the NAV MP3 unit will override any source of the motorcycle’s audio system to ensure navigation instructions are communicated when needed. The signals will also override the MP3 player.
Page 140
Cross Country MAGNUM Audio System Selecting Audio Sources Bluetooth Sources Bluetooth Source - Driver Tip: To utilize the Driver Device source, a device When a device is paired to a Bluetooth must be paired with the radio and the driver source and is in the process of connecting to source must be turned on.
Page 141
Cross Country MAGNUM Audio System Selecting Audio Sources Bluetooth Device Music Mode Settings The DRIVER DEVICE source will play the 4. Press to navigate through music source that is active on the connected selections until the device you want to device.
Page 142
Cross Country MAGNUM Audio System Selecting Audio Sources Bluetooth Device Music Mode Settings Music Mode Setting - Bluetooth Driver Source 1. When the Bluetooth device audio 5. To give a “THUMBS DOWN” for the source is active and playing, press and current song, Press and hold hold until the system enters the...
Page 143
Cross Country MAGNUM Audio System Voice Recognition Mode The radio features voice recognition when a Error Messages driver headset is connected and turned on. If voice command is initiated, but a device Radio Bluetooth functionality is dependent is not paired to the Driver Device source, on the capabilities of the device.
Page 144
Cross Country MAGNUM Audio System Voice Recognition Mode Receiving / Answering a Phone Call When a phone is paired to DRIVER Error Messages DEVICE, the audio system will allow the If your phone receives an incoming call driver to either answer or reject an incoming when the headset is not connected, the phone call.
Cross Country MAGNUM Audio System Siri Eyes Free Audio Mode Menus Entering Mode Menu The radio’s voice command mode supports the Siri Eyes Free feature on select iPhone models so you can use Siri without having 1. Press and hold until the system to look at the screen.
Page 146
Cross Country MAGNUM Audio System Audio Mode Menus Bass Setting Fader Setting Use the fader adjustment menu to control audio sound balance between front and rear speakers. Tip: The fader setting menu does not display if the headsets are selected for output. 1.
Page 147
Cross Country MAGNUM Audio System Audio Mode Menus Automatic Volume Control (AVC) Bluetooth Setup When set, this feature will lower or raise the Bluetooth Setup allows the user to pair and speaker/headset volume automatically, unpair headsets and devices. based on vehicle speed. 1.
Page 148
Cross Country MAGNUM Audio System Audio Mode Menus Bluetooth Setup Menu Bluetooth Setup Notes Driver Headset Pairing Tip: Incoming phone calls cannot be answered if driver headset is not connected. Press and release to send the calls to voice mail. •...
Page 149
Cross Country MAGNUM Audio System Audio Mode Menus Bluetooth Setup Menu Driver Headset Pairing Error Messages 10. When the headset is found, its name 1. If no headset is found, “NO DEVICE displays. FOUND” displays. Press and release to return to the Bluetooth Setup Menu.
Page 150
Cross Country MAGNUM Audio System Audio Mode Menus Bluetooth Setup Menu Driver Device Pairing The radio can be paired with Bluetooth 6. When the confirmation screen displays, devices such as smart phones. verify that the code on the device matches the code displayed on the 1.
Page 151
Cross Country MAGNUM Audio System Audio Mode Menus Bluetooth Setup Menu 3. To unpair individual devices in the Driver Headset location, scroll to the Unpairing / Reconnecting Devices device you want to unpair. The following steps reference the Driver Headset as an example. Use the same procedure to unpair other devices.
Page 152
Cross Country MAGNUM Audio System Audio Mode Menus Bluetooth Driver Device iPod Music Menu 1. Press to turn the Driver The iPod music menu allows the user to set Bluetooth Device source ON or OFF. how the device plays music tracks using the buttons.
Page 153
Cross Country MAGNUM Audio System Audio Mode Menus Tuner Clear Presets Radio Broadcast Data System (RBDS) 1. To clear all FM or AM radio station presets, press to select FM 1. Press to select a Radio or AM clear presets. Broadcast Data System (RBDS) setting.
Cross Country MAGNUM Audio System Audio System Diagnostics Key Pad Diagnostics The audio system diagnostic menu allows the following actions for you or your Key pad diagnostics allows the user to the VICTORY dealer: test the function of each button on the left- •...
Cross Country MAGNUM Audio System Audio System Diagnostics Audio Compliance Information Tuner Location Settings FCC and Industry Canada Compliance Statement The radio tuner can be set to the This equipment complies with FCC radia- geographical location where the motorcycle tion exposure limits set forth for an uncon- will be driven.