Victory Motorcycles OCTANE 2017 Rider's Manual
  1. Manuals
  2. Brands
  3. Victory Motorcycles Manuals
  4. Motorcycle
  5. OCTANE 2017
  6. Rider's manual

Victory Motorcycles OCTANE 2017 Rider's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

2017 Rider's Manual
OCTANE™

Advertisement

Table of Contents
loading

Related Manuals for Victory Motorcycles OCTANE 2017

Summary of Contents for Victory Motorcycles OCTANE 2017

  • Page 1 2017 Rider’s Manual OCTANE™...
  • Page 2 California Proposition 65 Warning This product contains or emits chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.
  • Page 3 2017 Rider’s Manual OCTANE™...
  • Page 4 Any reprinting, reuse or redistribution of the material in this document is expressly prohibited. VICTORY®, VICTORY MOTORCYCLES®, POLARIS® and OCTANE™ are trademarks of Polaris Industries Inc. Printed in U.S.A.
  • Page 5 WARNING Improper vehicle use can result in SEVERE INJURY or DEATH. NEVER Operate: • If you are under the age of 16 and without a driver’s license with motorcycle endorsement • Under the influence of drugs or alcohol • Off-road •...

  • Page 7: Table Of Contents

    Table of Contents Introduction ......... 6 Safety .

  • Page 8: Introduction

    VICTORY dealer can assist. To locate the nearest authorized VICTORY dealer, call 1-877- 737-7172 or visit www.victorymotorcycles.com. VICTORY motorcycles comply with all federal, state and local safety and emission regulations for the area of intended sale.

  • Page 9: Safety

    Safety About the Rider's Manual WARNING Failure to follow recommended precautions and procedures could result in severe injury or death. Always heed all safety precautions and follow all operation, inspection and maintenance procedures outlined in this manual. This rider’s manual contains information that is essential to safe riding and proper maintenance of your VICTORY motorcycle.
  • Page 10 Safety Safety Terms and Signal Words The following signal words and symbols appear throughout this manual and on your vehicle. Your safety and the safety of others is involved when these words and symbols are used. Become familiar with their meanings before reading the manual. The safety alert symbol indicates a potential personal injury hazard.

  • Page 11: Safe Riding Practices

    44. Failure to do so can result in serious engine damage. • Some VICTORY motorcycles include saddlebags, a windshield, a trunk, luggage racks or a passenger backrest as standard equipment. To maintain stability, be prepared to reduce...
  • Page 12 Safety Safe Riding Practices Follow these general safe riding practices: • Before each ride, perform the pre-ride inspections as outlined beginning on page 36. • Until you're thoroughly familiar with the motorcycle and all of its controls, practice riding where there is little or no traffic. Practice riding at a moderate speed on various road surfaces and in different weather conditions.
  • Page 13 Safety Safe Riding Practices • Reduce speed when: • the road has potholes, or is otherwise rough or uneven. • the road contains sand, dirt, gravel or other loose substances. • the road is wet, icy or oily. • the road contains painted surfaces, manhole covers, metal grating, railway crossings or other slippery surfaces.
  • Page 14 Safety Safe Riding Practices Carrying a Passenger Do not carry a passenger unless the motorcycle is equipped with passenger seat and passenger footrests. To carry a passenger safely: • Do not exceed the gross vehicle weight rating (GVWR). See the manufacturer’s label (on the left side of the frame at the steering head).
  • Page 15 Safety Safe Riding Practices Protective Apparel Wear protective apparel to decrease the risk of injury and increase riding comfort. • Always wear a helmet that meets or exceeds established safety standards. Approved helmets in the USA and Canada bear a U.S. Department of Transportation (DOT) label. Laws in some areas require that you wear an approved helmet.
  • Page 16 Safety Gross Vehicle Weight Rating (GVWR) WARNING! Exceeding the gross vehicle weight rating of your motorcycle can reduce stability and handling and could cause loss of control. NEVER exceed the GVWR of your motorcycle. The maximum load capacity of your motorcycle is the maximum weight you may add to your motorcycle without exceeding the GVWR.
  • Page 17 Safety Carrying Cargo Saddlebags When operating a motorcycle equipped with saddlebags: • Never ride at speeds exceeding 80 MPH (120 km/h). Depending on load and weather conditions, the maximum safe operating speed may be less. Saddlebags, combined with the lifting or buffeting effects of wind, can cause instability. •...

  • Page 18: Transporting The Motorcycle

    Safety Transporting the Motorcycle When transporting the motorcycle: • Use a truck or trailer. Never tow the motorcycle. Towing will impair steering and handling. • Restrain the motorcycle in an upright position to prevent fuel leaks. • Place the transmission in neutral. •...
  • Page 19 Safety Use of Accessories Because VICTORY cannot test and make specific recommendations concerning every accessory or combination of accessories sold, the operator is responsible for determining that the motorcycle can be safely operated with any accessories or additional weight. Use the following guidelines when choosing and installing accessories: •...
  • Page 20 Safety Fuel and Exhaust Safety WARNING Gasoline is highly flammable and explosive under certain conditions. • Always exercise extreme caution whenever handling gasoline. • Always turn off the engine before refueling. • Always refuel outdoors or in a well-ventilated area. •...
  • Page 21 Safety Safety Maintenance WARNING Failure to perform safety maintenance as recommended can result in difficult handling and loss of control, which could result in serious injury or death. Always perform the safety maintenance procedures as recommended in this manual. Perform safety-related maintenance and repairs promptly as outlined in the VICTORY Service Manual, or see your authorized VICTORY dealer for service.

  • Page 22: Electromagnetic Interference

    Safety Electromagnetic Interference This vehicle complies with the requirements of European regulation 44/2014/RVCR/Annex VII, United Nations ECE regulation 10 and Canadian ICES-002. Reporting Safety Defects If you believe that your vehicle has a defect that could result in a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Polaris Industries in writing.
  • Page 23 Safety Safety and Information Labels Labels are model-specific and market-specific. Your motorcycle may not contain all of the labels shown. Vehicle Identification Number (VIN) Stamped on Frame Vehicle Identification Number (VIN) on Manufacturing Label Vehicle Emission Control Information (VECI) Label Noise Emission Control Information (NECI) Label Evaporative Emissions Control Label Operator Warning/Fuel Recommendation Label...

  • Page 24: Component Identification

    Component Identification Driver’s Seat 13. Taillight Air Box (under fuel tank) 14. Left Front Turn Signal Fuel Tank 15. Ignition Switch Mirror 16. Battery (under seat) Fairing 17. Left Rear Turn Signal Right Front Turn Signal 18. Multi-Tool (behind license plate bracket) Headlight 19.

  • Page 25: Engine Identification Number

    Component Identification Handlebar/Console Components Clutch Lever Front Brake Fluid Reservoir Mirror Front Brake Lever Instrument Cluster Throttle Control Grip Fuel Cap Engine Identification Number The engine number is stamped into the bottom of the left crankcase near the sidestand. The first 8 digits are the engine model number.
  • Page 26 Component Identification Switches Left Control Right Control Turn Signal Switch Hazard Warning Flashers Switch High/Low Light Engine Stop/Run Switch Switch Engine Starter Switch Horn Switch Mode Button Symbol Switch Description Hazard Warning The hazard warning flashers switch activates and cancels the hazard Flashers Switch warning flashers.
  • Page 27 Component Identification Switches Engine Stop/Run Switch Use the engine stop/run switch to turn the engine off quickly. Turn the key off after the engine stops. • Press the top of the switch (STOP) to interrupt the circuits and stop the engine. The engine should not start or run when the switch is in the STOP position.
  • Page 28 Component Identification Switches Turn Signal Switch Move the turn signal switch to the left to activate the left turn signals. Move the switch to the right to activate the right turn signals. A signal ends when speed or distance reach preset levels. To end a signal manually, move the switch to the center and push it inward.
  • Page 29 Component Identification Switches Ignition/Light Key Switch The ignition/light key switch controls the electrical functions of the motorcycle. The switch is located on the ignition cover on the left side of the motorcycle. Motorcycle riders must remain as visible as possible at all times.

  • Page 30: Instruments, Features And Controls

    Instruments, Features and Controls Instrument Cluster Speedometer Indicator Lamps Multi-Function Display Speedometer The speedometer displays forward vehicle speed in either miles per hour or kilometers per hour. Indicator Lamps Lamp Indicates Condition High Beam This lamp illuminates when the headlamp switch is set to high beam. Chassis Fault The alert symbol illuminates if a chassis fault occurs.
  • Page 31 Instruments, Features and Controls Instrument Cluster Multi-Function Display MFD Indicators Lamp Indicates Condition Low Oil Pressure This lamp illuminates when oil pressure drops below a safe operating pressure while the engine is running. If this lamp illuminates while the engine is running above idle speed, turn the engine off as soon as safely possible and check the oil level.
  • Page 32 Instruments, Features and Controls Instrument Cluster Multi-Function Display Clock Tip: The clock must be reset any time the battery has been disconnected or discharged. 1. Turn the key to the ON position. Use the mode button to toggle to the odometer display. 2.
  • Page 33 Instruments, Features and Controls Instrument Cluster Multi-Function Display Engine Error Codes The error screen displays only when the Suspect Parameter Error Code CHECK ENGINE light is on or when it goes Number (SPN) Number (0-9) on and off during one ignition cycle. Error codes are not stored.
  • Page 34 Instruments, Features and Controls Brakes The front brake lever activates the front brake calipers. The rear brake pedal activates the rear brake caliper. For maximum brake effectiveness, apply the front brake lever and the rear brake pedal together. Anti-Lock Brake System (ABS) (if equipped) The anti-lock brake system automatically reduces or increases brake pressure as needed to provide optimum braking control, reducing the chance of wheel lock-up during hard braking events or when braking on rough, uneven, slippery or loose surfaces.

  • Page 35: Gear Shift Lever

    Instruments, Features and Controls Brakes Front Brake Lever Front Brake The front brake lever is located on the right Lever handlebar. This lever controls only the front brakes. The front brakes should be applied simultaneously with the rear brakes. To apply the front brake, pull the lever toward the handlebar.

  • Page 36: Throttle Control Grip

    Instruments, Features and Controls Throttle Control Grip The throttle control grip is located on the right Decrease Speed handlebar. Use the throttle control grip to control engine speed. While seated in the proper riding position: • Roll the grip rearward to open the throttle (increase engine speed and power).

  • Page 37: Fuel Cap

    Instruments, Features and Controls Fuel Cap Use the ignition key to open and close the fuel cap. Follow proper fueling procedures. See page 45. Tip: Prime the fuel pump if the tank is completely empty. 1. Lift the key slot cover on the fuel cap and insert the key.

  • Page 38: Pre-Ride Inspections

    Pre-Ride Inspections To keep your motorcycle in safe operating condition, always perform the recommended pre- ride inspections before each ride. This is especially important before making a long trip and when removing the motorcycle from storage. WARNING! Failure to perform the recommended pre-ride inspections could result in component failure while riding, which could result in serious injury or death.
  • Page 39 Pre-Ride Inspections Item Inspection Procedure Perform the following inspections with the engine off. Engine Oil Check the oil level. See page 38. Fuel Check the fuel level. See page 39. Coolant Level Check the coolant level in the recovery bottle. See page 57. Fluid Leaks Check the vehicle and the ground/floor for any fuel, oil, coolant or hydraulic fluid leaks.

  • Page 40: Engine Oil Level

    Pre-Ride Inspections Engine Oil Level With the semi-dry sump lubrication system, the engine oil level on the dipstick will fluctuate, depending on the motorcycle’s position and engine speed when the engine is turned off. To ensure a proper reading of the engine oil level, follow all inspection procedures closely.

  • Page 41: Fuel Level

    Pre-Ride Inspections Fuel Level 1. Position the motorcycle on level ground in the fully upright position. 2. Slowly open the fuel cap. See page 35. 3. View the fuel level in the tank. 4. Refuel as needed. See page 45 for fueling instructions. See page 104 for fuel specifications.

  • Page 42: Tire Pressure

    Pre-Ride Inspections Tire Pressure Check tire pressure before riding, when the tires are cold. This will provide the most accurate reading, as riding warms the tires and increases tire air pressure. Adjust tire pressure as needed based on the total weight of your intended load. Refer to the tire pressure table.

  • Page 43: Front Brake Lever

    Pre-Ride Inspections Front Brake Lever 1. Pull the front brake lever toward the handlebar and hold it. The lever should move freely and smoothly. The lever should feel firm and continue to feel firm until released. 2. Release the lever. It should return to its rest position quickly when released. 3.
  • Page 44 Pre-Ride Inspections Throttle 1. With the engine OFF, rotate the throttle control grip fully open and then release it. It should rotate smoothly from the rest position to the completely open position. It should return to the rest position quickly when released. 2.
  • Page 45 Pre-Ride Inspections Sidestand 1. On level ground, straddle the motorcycle and bring it to the fully upright position. 2. Move the sidestand up to the stored position and down to the fully extended position several times. It should move smoothly and quietly. Make sure the return spring holds the sidestand tightly in place when the sidestand is in the stored position.

  • Page 46: Operation

    Operation The operation section describes how to operate your VICTORY motorcycle to ensure the best performance and longevity of the engine and other components. Information includes: • Engine Break-in Period • Accelerating • Fueling • Braking • Starting the Engine •...
  • Page 47 Operation Engine Break-in Period Operating Speeds and Gears Odometer Reading Instructions Miles Kilometers 0-90 0-145 Do not operate for extended periods above 1/3 throttle or at any one throttle position. Vary engine speed frequently. 91-300 146-483 Do not operate for extended periods above 1/2 throttle or at any one throttle position.
  • Page 48 Operation Engine Break-in Period Priming the Fuel System If the motorcycle runs out of fuel, prime the fuel system before attempting to restart the engine. 1. Fill the fuel tank. 2. Turn the ignition switch to the ON position. 3. Move the engine stop/run switch to the RUN position. 4.
  • Page 49 Operation Engine Break-in Period Starting the Engine The starter interlock system allows the engine to be started only when the transmission is in neutral, or when the transmission is in gear with the clutch disengaged (clutch lever pulled in). Tip: If the motorcycle runs out of fuel, prime the system before attempting to restart the engine. See page 46.

  • Page 50: Shifting Gears

    Operation Shifting Gears WARNING! Forced shifting (with clutch engaged) could cause damage to the engine, transmission and drive train. Such damage could cause loss of control, which could result in serious injury or death. Always pull the clutch lever fully toward the handlebars to disengage the clutch before shifting gears. Your motorcycle is equipped with a six-speed transmission.
  • Page 51 Operation Shifting Gears Shifting Gears While Driving 1. Start the engine. See page 47. 2. With the engine at idle speed, apply the front brakes. 3. Disengage the clutch (pull the clutch lever fully toward the handlebar). 4. Push the toe lever downward until you feel it stop in first gear. 5.

  • Page 52: Stopping The Engine

    Operation Accelerating Accelerate by opening the throttle (rolling the throttle control grip rearward). The more quickly you open the throttle, the more quickly the motorcycle accelerates. For even acceleration, open the throttle with a smooth, continuous motion. When you reach the recommended speed for upshifting, shift up one gear.
  • Page 53 Operation Parking the Motorcycle Choose a firm level surface to park the motorcycle. 1. When fully stopped, shift into neutral. 2. Stop the engine. 3. Fully extend the sidestand. 4. Turn the handlebars to the left and lean the motorcycle to the left until the sidestand firmly supports the motorcycle.

  • Page 54: Maintenance

    Maintenance Any qualified repair shop or person may maintain, replace, or repair the emission control devices or systems on your vehicle. An authorized VICTORY dealer can perform any service that may be necessary for your vehicle. VICTORY recommends VICTORY parts for emissions-related service, however equivalent parts may be used for such service.

  • Page 55: Major Maintenance

    Maintenance Major Maintenance Major repairs typically require technical skills and specially designed tools. Emission system service requires special tools and training and can be performed by your dealer. For more information, see the VICTORY Service Manual. Your authorized VICTORY dealer can assist.
  • Page 56 Maintenance Periodic Maintenance Table See table key below Odometer Reading in Miles (Kilometers) Component Page Air Filter Crankcase Ventilation System Oil Lines/Oil System Inspection Cooling System/Radiator *Engine Oil and Filter Valve Lash Clearance Exhaust System Spark Plugs Battery **Brake Fluid 65-66 Brake Pads Clutch Lever...

  • Page 57: Engine Oil And Filter Change

    Maintenance Engine Oil and Filter Change Follow all instructions carefully. Do not overfill. Change the engine oil at the intervals specified in the periodic maintenance table beginning on page 54. Change the oil more frequently if the motorcycle is subjected to severe use, especially operation in cold weather.
  • Page 58 Maintenance Engine Oil and Filter Change 7. Place a drain pan or shop towels under the oil filter. Using an oil filter wrench, turn the filter counter-clockwise to remove it. 8. Using a clean dry cloth, clean the filter sealing surface on the engine. 9.
  • Page 59 Maintenance Cooling System The engine coolant level is controlled by the recovery system. Recovery system components are the recovery bottle, the radiator filler neck, the radiator pressure cap and the connecting hose. As coolant operating temperature increases, the expanding (heated) excess coolant is forced out of the engine, past the pressure cap, and into the recovery bottle.

  • Page 60: Air Filter

    Maintenance Air Filter Inspect and replace the air filter at the intervals specified in the periodic maintenance table beginning on page 54. Inspect more often if riding in unusually wet or dusty conditions. 1. Remove the seat. See page 76. 2.
  • Page 61 Maintenance Fuel System CAUTION! Always observe all fuel safety procedures when inspecting or servicing the fuel system. See page 18. Fuel Tank Removal Before beginning, be prepared to place the fuel tank in a secure location to avoid scratching the finish and to catch any fuel that may leak or drip from disconnected hoses or fittings. Please read the entire removal and reinstallaton procedure Fuel Tank before beginning.
  • Page 62 Maintenance Fuel System Fuel Tank Removal 9. Disconnect the fuel pump electrical Step 9 connector by depressing the release tab on Step 11 the connector body. Gently pull it free from the fuel pump. 10. Wrap a shop towel around the fuel fitting. 11.
  • Page 63 Maintenance Fuel System Fuel Tank Installation 4. Pivot the rear of the tank upward to access the Step 7 tank bottom. Support the rear of the tank in this position. Step 6 5. Remove the plug tool from the fuel pump fitting.
  • Page 64 Maintenance Clutch (Mechanical) Mechanical Clutch Lever Freeplay Inspect clutch lever freeplay at the intervals recommended in the periodic maintenance table. See page 54. NOTICE: Incorrectly adjusted freeplay (cable too tight or too loose) will result in premature clutch wear and/or failure. 1.
  • Page 65 Maintenance Clutch (Mechanical) Mechanical Clutch Cable Lubrication Lubricate control cable barrel ends at the intervals recommended in the periodic maintenance table. See page 54. NOTICE: The clutch cable is factory-lubricated. Additional lubrication could be detrimental to cable performance. Replace the clutch cable assembly if binding or sticking occurs. DO NOT lubricate between the cable and sheath.
  • Page 66 Maintenance Brake Systems Brake Hoses/Connections Inspect all brake hoses and connections for dampness or stains from leaking or dried fluid. Tighten any leaking connections and replace components as necessary. For more information, see the VICTORY Service Manual. Your authorized VICTORY dealer can assist.
  • Page 67 Maintenance Brake Systems Brake Fluid Precautions WARNING Using the wrong fluid or allowing air or contaminants into the fluid system can damage the system seals or result in a malfunction that could lead to serious injury or death. Use only DOT 4 brake fluid from a sealed container.
  • Page 68 Maintenance Brake Systems Front Brake Fluid Change the brake fluid at the intervals recommended in the periodic maintenance table beginning on page 54. Always add brake fluid from a new, unopened container. Always use the recommended fluid. See page 104. 1.
  • Page 69 Maintenance Brake Systems Brake Pads Inspect each front brake pad on both sides of the front disc. Friction Inspect each rear brake pad on both sides of the rear disc. Material When checking brake pad friction material thickness, check each brake caliper for dampness or stains from leaking or dried brake fluid.

  • Page 70: Drive Belt Condition

    Maintenance Drive Belt Condition Inspect the rear drive belt at the intervals specified in the periodic maintenance table beginning on page 54. Replace the drive belt if it is cracked or has broken teeth or frayed edges. No matter its condition, the drive belt should be replaced at periodic intervals. For more information, see the VICTORY Service Manual.
  • Page 71 Maintenance Rear Suspension Rear Shock Preload (Ride Height) Inspection Periodically measure rear shock preload. Have an assistant help with this procedure. For the most comfortable ride and proper ground clearance, adjust preload if ride height is out of specification. 1. Verify that tire pressure is at specification.
  • Page 72 Maintenance Rear Suspension Rear Shock Preload (Ride Height) Adjustment 1. Verify that tire pressure is at specification. See page 73. 2. Rest the motorcycle on the sidestand. Unload the rear suspension as much as possible. 3. Spray a light lubricant on the adjuster where it contacts the spring.
  • Page 73 Maintenance Rear Suspension Swing Arm and Rear Axle Inspection 1. Sit in the operator’s seat and slowly bounce the rear suspension a few times. Make sure the suspension moves freely without binding. Listen for abnormal noises. 2. Elevate and support the motorcycle with the rear tire slightly off the floor. See page 53. 3.

  • Page 74: Steering Head Inspection

    Maintenance Steering Head Inspection 1. Elevate and support the motorcycle with the front tire slightly off the floor. See page 53. CAUTION! Make sure the motorcycle is stable when elevated. Injury may occur if the motorcycle tips or falls. 2. Turn the handlebars from stop to stop. The action should be smooth but not loose. Make sure wires, hoses and control cables do not interfere with smooth steering.
  • Page 75 Maintenance Tires WARNING Operating the motorcycle with improper tires or with improper or uneven tire pressure could cause loss of control or accident. Always use the correct size and type of tires specified for your vehicle. Always maintain proper tire pressure as recommended in the rider's manual and on safety labels. Tire Pressure Always check and adjust tire pressure when tires are cold.

  • Page 76: Wheel Inspection

    Maintenance Tires Tire Replacement Tires, rims, innertubes and air valves must be correctly matched to wheel rims. Use only the proper size tires specified with the same or higher load and speed ratings. VICTORY- recommended tires provide proper clearance between fenders, swingarm, drive belts and other components.
  • Page 77 Maintenance Anti-Lock Brake System (ABS) Tone Ring/Sensor Inspection (if equipped) Visually inspect for damaged teeth on the front and rear ABS tone rings. Inspect for nicks and dents on the face of the teeth. The teeth edges should be consistent in appearance. If a tone ring is damaged, see your VICTORY dealer for replacement as soon as possible.
  • Page 78 Maintenance Seat Removal/Installation 1. Remove the seat retaining bolt at the front Seat Bolt of the seat. The multi-tool can be used to remove the seat bolt (located behind the license plate bracket). NOTICE: Use caution to avoid contact with the fuel tank when removing or installing the seat.

  • Page 79: Battery Removal

    Maintenance Battery The motorcycle battery is a sealed, maintenance-free battery. Do not remove the battery cap strip for any reason. Keep the battery connections clean and tight at all times. WARNING Battery electrolyte is poisonous. It contains sulfuric acid. Serious burns can result from contact with skin, eyes or clothing.
  • Page 80 Maintenance Battery Battery Charging If your motorcycle will not be used for a period of four (4) weeks or longer, a maintenance charger should be connected to the battery. A maintenance charger can be purchased through your authorized VICTORY dealer. 1.

  • Page 81: Fuse Replacement

    Maintenance Fuse Replacement The standard fuse box is located under the seat. This fuse box houses all standard service fuses and the automatic circuit breakers. Fuse application and size are provided on a label on the fuse box cover. Main Vehicle The main vehicle fuse is located on the wiring Fuse...

  • Page 82: Electrical Precautions

    Maintenance Electrical Precautions Be aware of the following precautions regarding the electrical system to avoid disruption of electrical signals and possible system malfunction. • DO use ONLY genuine VICTORY parts and accessories designed for your model, and follow the instructions provided. Equivalent parts may be used for emissions-related purposes.
  • Page 83 Maintenance Fairing Removal/Installation 1. Remove the turn signal mounting fasteners on both sides of the motorcycle. 2. Rotate the signals forward toward the front tire. 3. Remove the two M8 fairing bracket fasteners. 4. Carefully slide the fairing straight forward to clear the headlight. 5.

  • Page 84: Headlight Aim Inspection

    Maintenance Headlight Aim Inspection On high beam, the center of highest intensity (appearing as a diamond shape) should be 7.5 in. (19 cm) lower than the headlamp bulb and centered straight ahead at 25 feet (7.6 m). 25 ft. (7.6 m) 7.5 in.

  • Page 85: Headlight Lamp Replacement

    Maintenance Headlight Lamp Replacement 1. Remove the headlight retaining screw. 2. Lift the bottom of the headlight upward to unhook the top from the base. Slide the headlight out of the fairing. 3. Disconnect the wire harness from the headlight by grasping the harness connector and pulling it straight back.

  • Page 86: Troubleshooting

    Maintenance Troubleshooting For your personal safety, do not attempt inspection or repairs not fully described in this rider’s manual. Contact an authorized dealer or other qualified person for service if you cannot determine the cause of a problem or if the inspection/repair exceeds your mechanical ability or tool resources.
  • Page 87 Maintenance Troubleshooting Shifting Difficulties or Hard to Find Neutral Possible Cause Possible Remedy/Action Clutch damage Replace clutch. Clutch cable not adjusted properly See page 62. Your dealer can provide an inspection and adjustment. Shift linkage not adjusted properly Your dealer can provide an inspection and adjustment. Incorrect oil or oil in poor condition Replace the oil with the recommended oil.

  • Page 88: Cleaning And Storage

    Cleaning and Storage VICTORY Cleaning Products This section provides tips on the very best way to clean, polish and preserve every surface of your beautiful new VICTORY motorcycle. We recommend the use of our VICTORY cleaning and polishing products and accessories, which have been specially designed to offer the best care possible for your VICTORY motorcycle.
  • Page 89 Cleaning and Storage Windshield Care (if equipped) Clean the windshield with a soft cloth and plenty of warm water. Dry with a soft clean cloth. Remove minor scratches with a high-quality polishing compound designed for use on polycarbonate surfaces. NOTICE: Brake fluid and alcohol will permanently damage the windshield. Do not use glass cleaners, water or soil repellents, and petroleum or alcohol based cleaners on the windshield, as these products can damage the windshield.
  • Page 90 Cleaning and Storage Gloss Clear Coat Finish Care The Axalta Sports and Equipment Finish System was used to provide the original gloss finish on your motorcycle. This finish system provides superior protection against the elements. To maximize the benefits of this system, use the following guide to care for the gloss finish on your motorcycle.
  • Page 91 Cleaning and Storage Polished Aluminum Care When a VICTORY motorcycle is new, the polished aluminum wheels, hand levers and shifter shine like chrome. Ultraviolet (UV) rays and oxidation will cause polished aluminum to grow dull, however, if it’s not properly polished and protected. VICTORY Awesome Metal Polish will clean, polish and protect these aluminum surfaces.
  • Page 92 Cleaning and Storage Polishing the Motorcycle Premium Polishing for Long-Lasting Protection The premium method of polishing paint and chrome utilizes the latest in high-quality polymer technology that provides the longest-lasting protection available in the polish industry today. VICTORY Liquid Spray Wax for windshields, paint and chrome is formulated for polishing after washing and can be sprayed on wet or dry surfaces.

  • Page 93: Clean And Protect The Motorcycle

    Cleaning and Storage If you will not operate the motorcycle for several months, such as during the winter, store the motorcycle to prevent damage to the fuel system and the battery and to protect components from corrosion or deterioration. During storage you might use products that are potentially hazardous;...

  • Page 94: Battery Care

    Cleaning and Storage Battery Care 1. Remove the battery. See page 77. 2. Clean oxidation from battery posts and cable connectors with a wire brush. Wash the posts and cable connectors with a solution of one part baking soda to 16 parts water. Rinse with clean water and wipe dry.

  • Page 95: Removal From Storage

    Cleaning and Storage Removal From Storage 1. Verify that tire pressure is at specification. 2. Install a fully charged battery. 3. Perform an electrical inspection. 4. Check the oil level. If the motorcycle was stored in an area subject to wide swings in temperature and humidity (such as outdoors), change the engine oil before starting the engine.

  • Page 96: Warranties

    Victory Motorcycles Warranty Policy Limited Warranty Victory Motorcycles Division, Polaris Industries Inc., 2100 Highway 55, Medina, Minnesota 55340 gives a TWO YEAR LIMITED WARRANTY on all components of your VICTORY motorcycle against defects in material or workmanship. This warranty covers parts and labor charges for repair or replacement of defective parts and begins on the date of purchase by the original retail purchaser.
  • Page 97 LIMITED WARRANTY. ALL OTHER IMPLIED WARRANTIES (INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY) ARE LIMITED IN DURATION TO THE ABOVE 24 MONTH WARRANTY PERIOD. VICTORY MOTORCYCLES DISCLAIMS ALL EXPRESS WARRANTIES NOT STATED IN THIS WARRANTY. SOME STATES DO NOT PERMIT THE EXCLUSION...
  • Page 98 In the country where your motorcycle was purchased: Warranty or Service Bulletin repairs must be done by an authorized VICTORY MOTORCYCLES dealer. If you move or are traveling within the country where your motorcycle was purchased, Warranty and Service Bulletin repairs may be requested from any authorized VICTORY MOTORCYCLES dealer.
  • Page 99 DEALER’S AUTHORIZED LOCATION. This policy does not apply to vehicles that have received authorization for export from VICTORY MOTORCYCLES. Dealers may not give authorization for export. You should consult an authorized dealer to determine this vehicle’s warranty or service coverage if you have any questions. This policy does not apply to vehicles registered to government officials or military personnel on assignment outside the country of the selling dealer’s authorized location.

  • Page 100: Motorcycle Noise Regulation

    Otherwise, the owner may become subject to penalties under state and local ordinances. Noise Emission Warranty VICTORY MOTORCYCLES warrants that this exhaust system, at the time of sale, meets all applicable U.S. EPA Federal noise standards. This warranty extends to the first person who buys this exhaust system for purposes other than resale, and to all subsequent buyers.
  • Page 101 Victory Motorcycle Division, Polaris Industries Inc. - Emission Control System Warranty Statement Your Warranty Rights and Obligations The California Air Resources Board and VICTORY MOTORCYCLES (hereinafter VICTORY) are pleased to explain the emission control system warranty on your 2014 or later VICTORY motorcycle. In California, new motor vehicles must be designed, built and equipped to meet the state’s stringent anti-smog standards.
  • Page 102 Warranties Emissions Control System Warranty I. Coverage Warranty defects shall be remedied during customary business hours at any authorized VICTORY dealer located within the United States of America in compliance with the Clean Air Act and applicable regulations of the United States Environmental Protection Agency and the California Air Resources Board.
  • Page 103 Such maintenance may be performed at a service establishment or by any individual. The warranty period begins on the date the motorcycle is delivered to an ultimate purchaser. VICTORY MOTORCYCLES 2100 Highway 55 Medina, MN 55340...

  • Page 104: Specifications

    Specifications VICTORY OCTANE Dimensions (Dimensions and specifications may vary with features, options and accessories) Overall Length 89.4 in. (2271 mm) Overall Width 35.4 in. (898 mm) Overall Height 42.2 in. (1071 mm) Seat Height Unladen 26.9 in. (683 mm) Laden 25.9 in. (658 mm) Wheelbase 61.6 in.
  • Page 105 Specifications VICTORY OCTANE Drive System Primary Drive Gear Drive Wet Clutch Clutch Type Wet, Multi-Plate Primary Reduction Ratio 1.674:1 Transmission Type 6 Speed/Sliding Mesh/Foot Shift 1st Gear Ratio 2.769:1 2nd Gear Ratio 1.882:1 3rd Gear Ratio 1.500:1 4th Gear Ratio 1.273:1 5th Gear Ratio 1.125:1...

  • Page 106: Fuel Specifications

    Specifications Fuel Specifications For best performance, use only unleaded gasoline with a 91 pump octane minimum (R+M/2 Method). DO NOT USE E-85 GASOLINE OR GASOLINE CONTAINING METHANOL. Using E85 or gasoline/methanol blends can result in poor starting and driveability, engine damage and damage to critical fuel system components.

  • Page 107: Maintenance Record

    Maintenance Record SERVICE PERFORMED COMMENTS MILES DATE PERFORMED (KM)
  • Page 108 Maintenance Record SERVICE PERFORMED COMMENTS MILES DATE PERFORMED (KM)

  • Page 109: Index

    Index About the Rider’s Manual....7 Clutch Lever ......34 ABS.
  • Page 110 Index Fuel Level ......39 Noise Control System Tampering ... . . 98 Fuel Safety .
  • Page 111 Index Signal Words......8 Throttle Control Grip ..... . 34 Spark Plugs .
  • Page 112 To locate your nearest dealer, call 1-877-737-7172 or visit www.victorymotorcycles.com Victory Motorcycles 2100 Highway 55 Medina, MN 55340 Part No. 9926391 Rev 01 Printed in USA...

Table of Contents