Operation; Maintenance; Glass Replacement - Jøtul GF 100 DV II Installation And Operation Instructions Manual

Operation

Familiarize yourself with the controls of your stove. Make
sure that anyone else using the appliance is also familiar
with the controls and operation procedures. Always
follow the Lighting Instructions on the inside back cover
of this manual and also located on the Rating Plate
attached to the burner assembly.
1. Once the pilot is lit, burner operation is controlled by
the rocker switch located at the left rear corner of the
stove. Use the T-STAT position for the optional thermo-
static or remote control functions. See fig. 32.
2. During the first few fires, you may notice odor and/or
smoke from the stove. This is normal and results from
burn-off of manufacturing residue and curing of
materials. You may find it helpful to provide additional
ventilation and fresh air to alleviate this condition.
3. Condensation may occur on the glass upon each
lighting of the appliance. This "fog" will disappear as
the appliance heats up.
4. Keep the controls and the area under the appliance
free of debris, vacuum this area frequently. Always
keep the appliance area clear and free from combus-
tible materials, gasoline and other flammable liquids.
If a vacuum is used during any service on the stove,
ALWAYS be sure the stove is cold and there are NO
hotembers or sparks.
5. This appliance has a continuous burning pilot flame.
Exercise caution when using products having combus-
tible vapors. Always shut-off gas supply while servic-
ing the stove.
6. CAUTION: DO NOT OPERATE THIS APPLIANCE WITH
THE GLASS REMOVED CRACKED OR BROKEN. Replace-
ment of the glass should be done by a licensed or
qualified service person. Use only replacement glass
provided by your authorized Jøtul dealer. Never use
any substitute materials.
WARNING: OBSERVE CAUTION WITH THE GLASS. THE
GLASS PANEL MAY SHATTER UNEXPECTEDLY IF STRUCK
WITH AN OBJECT. ALWAYS HANDLE THE GLASS PANEL
WITH CARE. WHEN SERVICING THE STOVE ALWAYS
PULL THE GLASS ASSEMBLY STRAIGHT UP FOR RE-
MOVAL.
7. Clean the glass only when necessary. Wipe surface
with a clean, damp soft cloth. Follow with a dry, soft
towel as desired. Take care not to scratch the glass
surface.
WARNING: DO NOT USE ABRASIVE CLEANERS ON THE
GLASS. NEVER CLEAN THE GLASS WHEN IT IS HOT.
22
Figure 32. Burner Control Switch location.

Maintenance

This appliance and its venting system should be in-
spected before use and at least annually by a qualified
service technician.
IMPOR IMP IMP IMP IMP
AL AL AL AL ALW W W W W A A A A A Y Y Y Y Y S S S S S T T T T T U U U U U R R R R R N OFF N OFF N OFF N OFF T T T T T H H H H H E G N OFF E G E G E G E GA A A A A S SU
B B B B B EF EF EF EF EFOR OR OR ORE AN OR E AN E AN E ANY SER E AN Y SERVIC Y SER Y SER Y SER VICE E E E E W W W W W OR VIC VIC VIC ORK IS PER OR OR OR
S S S S S T T T T T O O O O O VE. VE. VE.
VE. VE.
V V V V V en en ent t t t t S S S S Sy y y y y stem: en stem: The vent components should be inspected stem: stem:
en stem:
annually to confirm it is clear of obstructions and all
connections are secure. Any joints disconnected must be
resealed using high temperature sealant when reas-
sembled.
F F F F F ir ir ir ir irebo ebo ebo ebox Cleaning: ebo x Cleaning: The firebox should be vacuumed x Cleaning: x Cleaning: x Cleaning:
annually to remove any surface build up. Be sure to
vacuum or wipe off the pilot assembly and burner orifice
and burner tube. Handle the logset carefully as it is very
fragile.
Glass Cleaning: Glass Cleaning: Use warm water and a soft cloth. Do not Glass Cleaning: Glass Cleaning: Glass Cleaning:
use abrasive cleaning agents or strong detergents on the
glass. Be sure the glass is cool before cleaning.
Gasket et et et et Inspec Gask Gask Gask Gask Inspec Inspec Inspection: Inspec tion: tion: tion: tion: Inspect the glass gasket at least
annually. Examine the ribbon gasket for signs of deterio-
ration and make sure the gasket has a positive seal.
Replace the gasket if it appears worn or damaged. Refer
to the replacement parts list on page 27.
Enamel Car ar ar ar are: e: e: e: e: Enamel C Enamel C Enamel C Enamel C
DO NOT ATTEMPT TO CLEAN HOT ENAMEL
SURFACES. Clean only cold enamel surfaces with a soft
damp cloth and polish with a clean dry cloth.
DO NOT USE SOAPY OR ABRASIVE SOLUTIONS.
These can cause stains. Coffee, tea, and fruit juices will
also stain.
Avoid contact with metal objects. Trivets, kettles,
or pots, can damage the enamel.
ORT T T T T AN OR OR OR AN AN ANT T T T T : : : : : AN
S SUPPL S SU S SU S SU PPL PPLY Y Y Y Y T T T T T O O O O O T T T T T H H H H H E S PPL PPL E S E S E S E ST T T T T O O O O O VE VE VE VE VE
K IS PER K IS PER K IS PER K IS PERF F F F F ORMED ON ORMED ON ORMED ON ORMED ON ORMED ON T T T T T H H H H H E E E E E