Advertisement
Quick Links
Advertisement
Related Manuals for Insportline STAR
Summary of Contents for Insportline STAR
- Page 1 USER MANUAL IN 723 Multigym inSPORTline STAR...
-
Page 2: Table Of Contents
PART LIST Part no Descritpion Q‘ty Base frame Rear stabilizer Front vertical support Upper beam Front stabilizer Seat support Right butterfly arm Left butterfly arm Butterfly arm support Foot plate fixing beam Leg curler Upper pulling bar Lower pulling bar Foam roller Weight guidance rod Weight protector... - Page 3 Weight washer Weight sleeve Raised pulley Flat pulley Ankle strap Foot plate Axle for foot plate Rubber buffer Reinforcing board Bushing D31.8xD16.2x7T Square hollow cap Bushing D18xD10X14.5 Arm curl pad Arm curl support Hand grip Support of single pulley support Butterfly hand grip Spring knob Chain (12 links)
- Page 4 INSTRUCTION ASSEMBLY INSTRUCTION ASSEMBLY: STEP 1:...
-
Page 6: Base Frame
Fix the rear stabilizer(2) and 2 weight guidance rods(16) by using 2 flat washers(101), Fix the rear stabilizer(2) and 2 weight guidance rods(16) by using 2 flat washers(101), 2 bolts(115) and 2 foot 2 bolts(115) and 2 foot caps(32). STEP •... -
Page 7: Front Vertical Support
STEP • Fix the front vertical support(3), base frame(1) and hooking plate(21) Fix the front vertical support(3), base frame(1) and hooking plate(21) by using 2 nylon nuts(102), 4 flat washers(101),and 2 bolts(104). washers(101),and 2 bolts(104). • Assemble the cross plate (27), 2 round buffers(39) from the bottom , then assemble Assemble the cross plate (27), 2 round buffers(39) from the bottom , then assemble Assemble the cross plate (27), 2 round buffers(39) from the bottom , then assemble 9 lower weight plates(47) and 1 upper weight plate(46) through the weight guidance... -
Page 8: Upper Beam
STEP • Assemble the upper beam(4), onto the front support(31), weight guidance rod by Assemble the upper beam(4), onto the front support(31), weight guidance rod by using 3 square plastic caps(35), then sequentially with 2 bolts(104), 4 flat caps(35), then sequentially with 2 bolts(104), 4 flat washers(101), 1 reinforcing board, 2 nylon washers(101), 1 reinforcing board, 2 nylon nut(102);... - Page 9 STEP • Fix the butterfly arm support (9) to the upper beam(4) by using 1 bolt(113), 2 flat utterfly arm support (9) to the upper beam(4) by using 1 bolt(113), 2 flat utterfly arm support (9) to the upper beam(4) by using 1 bolt(113), 2 flat washers(106), 1 nylon nut (107) and 2 bushings(31).
- Page 10 STEP 6 • Assemble the right & left butterfly arm (7) & (8) onto the butterfly arm support (9) by Assemble the right & left butterfly arm (7) & (8) onto the butterfly arm support (9) by Assemble the right & left butterfly arm (7) & (8) onto the butterfly arm support (9) by using 2 nylon nuts (102), 1 flat washer (101) .
- Page 11 STEP • fix the leg curler(11) onto the base frame by using 2 bushings(31), flat washer(101), fix the leg curler(11) onto the base frame by using 2 bushings(31), flat washer(101), fix the leg curler(11) onto the base frame by using 2 bushings(31), flat washer(101), 1 flat washer(106), 1 nylon nut(102) and 1 bolt(111) ,and then fix the square plastic nylon nut(102) and 1 bolt(111) ,and then fix the square plastic cap (35) into the leg curler(11).
-
Page 12: Seat Support
STEP • fix the foam (45) onto the hand grip (68) and then fix the hand grip under to the seat fix the foam (45) onto the hand grip (68) and then fix the hand grip under to the seat fix the foam (45) onto the hand grip (68) and then fix the hand grip under to the seat support (6) with 2 bolt (100) , 4 flat washer (101). - Page 13 STEP Thread the foam roller(44) through the leg curler(11),then coat the foam Thread the foam roller(44) through the leg curler(11),then coat the foam roller with the foam(44),then fix the round plastic cap to the end of the foam roller. foam(44),then fix the round plastic cap to the end of the foam roller.
-
Page 14: Right Butterfly Arm
STEP Connection of cable (butterfly arm)(51) and assembly the pulley: Connection of cable (butterfly arm)(51) and assembly the pulley: (1) hooking one end of the cable to the right e end of the cable to the right butterfly arm (7) and slide the other end of butterfly arm (7) and slide the other end of the cable along the pulley, at the same time you the cable along the pulley, at the same time you need to fix the 1 raised pulley (56) into the 1 single pulley support (20) by 2 plastic ring... -
Page 15: Butterfly Arm Support
(3) and then upwards the cable and the other end will be joined to the left butterfly. The (3) and then upwards the cable and the other end will be joined to the left butterfly. The (3) and then upwards the cable and the other end will be joined to the left butterfly. The assembly way of left side will be same as the right one. -
Page 16: Leg Curler
STEP assembly the cable (leg curler) and pulley at the same time: assembly the cable (leg curler) and pulley at the same time: • the cable going way as drawing . From one end of cable to the other, there will be 5 raised pulley the cable going way as drawing . -
Page 17: Lower Pulling Bar
• connect the lower pulling bar (13) with one of cable (52) using 2 hook (25) and 1 chain (72). And connect the lower pulling bar (13) with one of cable (52) using 2 hook (25) and 1 chain (72). And connect the lower pulling bar (13) with one of cable (52) using 2 hook (25) and 1 chain (72). - Page 18 • (2)on the top of the weight protector (17), the cross plate (27) cover and connect with the 4 rod of (2)on the top of the weight protector (17), the cross plate (27) cover and connect with the 4 rod of (2)on the top of the weight protector (17), the cross plate (27) cover and connect with the 4 rod of cover fixing plate (28) and then fix the 2 sleeve (40) through the weigh guidance ro fixing plate (28) and then fix the 2 sleeve (40) through the weigh guidance rod(16).
- Page 19 EXPLODED DRAWING:...
- Page 20 EXERCISE PICTURES:...