Status Code Entry Chart - Xerox 8825 Service Manual

Status Code Entry Chart

Table 1 Status Code Entry Chart
Status Description
Code
C1-01 Position sensor error
C2-01 The Roll 1, 2, or 3 position
C3-01 sensor did not actuate or
deactuate.
No
RAP
C1-04 Media registration sensor
error
The media sensor did not
actuate or deactuate when
feeding from roll 1, 2, or 3.
C1-05 Motion sensor error
C2-05 Motion was not detected or
C3-05 the media stopped moving
when feeding from roll 1, 2, or
No 3.
RAP
C3-06 Roll 2 position sensor error
No 8825 with Tag/MOD 90
RAP Media was not detected at the
Roll 2 position sensor when
feeding from roll 3.
C3-07 Roll 1 position sensor error
No Media was not detected at the
RAP Roll 1 position sensor when
feeding from Roll 3.
8825/8830 Printer
Components BSD PL
Ref Ref
Roll 1 position sensor BSD PL
(Q1) 7.2 7.1
Roll 2 position sensor BSD PL
(Q2) 8825 with Tag/ 7.3 1.1A
MOD 90 BSD
Roll 3 position sensor 7.4
(Q3)
Main PWB (A3)
NOTE: The sensors are
interchangeable.
Media registration sensor BSD PL
(A21Q1) 8.1 8.2
Main PWB (A3) PL
Driver PWB 1.1A
Registration Rolls PL
Transport Driver Motor 8.3
Motor Driver PWB
Roll 1 motion sensor BSD PL
(Q4) 7.2 7.1
Roll 2 motion sensor BSD PL
(Q5) 8825 with Tag/MOD 7.3 1.1A
90 BSD PL
Roll 3 motion sensor 7.4 7.2
(Q6) BSD
Main PWB (A3) 7.1
Driver PWB
Motor Driver PWB
Media Feed Rolls
Media Feed Clutch
Media Feed Drive Motor
NOTE: The sensors
and the clutches are
interchangeable.
Roll 2 position sensor BSD PL
(Q2) 8825 with Tag/MOD 7.3 7.1
90 PL
Main PWB (A3) 1.1A
Roll 1 position sensor BSD PL
(Q1) 7.2 7.1
Main PWB (A3) PL
1.1A
Table 1 Status Code Entry Chart
Status Description
Code
C1-09 Firmware error
C2-09 This is a firmware problem.
C3-09 Press power off (0) then
No power on (1). If problem per-
RAP sists, replace the firmware.
C1-19 This is a Firmware problem
C2-19 This is a firmware problem.
C3-19 Press power off (0) then
No power on (1). If problem per-
RAP sists, replace the firmware.
C1-29 This is a Firmware problem.
C2-29 This is a firmware problem.
C3-29 Press power off (0) then
No power on (1). If problem per-
RAP sists, replace the firmware.
C1-39 This is a Firmware problem.
C2-39 This is a firmware problem.
C3-39 Press power off (0) then
No power on (1). If problem per-
RAP sists, replace the firmware.
C1-59 Light reflecting off of a
C2-59 piece of media or from rear
C3-59 of drawer or a baffle.
RAP
C4-24 Registration sensor error
The cut sheet does not reach
No the media registration sensor
RAP in time.
C4-34 Sheet feed sensor error
The sheet feed sensor deac-
No tuated too early while making
RAP a print. The operator may
have removed the cut sheet
media.
01/02
1-7
Components BSD PL
Ref Ref
PL
1.1A
PL
1.1A
PL
1.1A
PL
1.1A
Roll 1 position sensor BSD PL
(Q1) 7.2 1.1A
Roll 2 position sensor BSD PL
(Q2); 8825 with Tag/ 7.3 7.1
MOD 90 BSD
Roll 3 position sensor 7.4
(Q3)
Main PWB (A3)
Media registration sensor BSD PL
(A21Q1) 8.1 8.2
Main PWB (A3) PL
Registration Rolls 1.1A
Transport Drive Motor PL
Transport Motor Driver 7.2
PWB PL
Cut Sheet Feed Clutch / 8.3
Rolls
Driver PWB
Sheet feed sensor (Q2) BSD PL
8825 with Tag/MOD 90 8.1 8.4
Main PWB (A3) PL
1.1A
Service Call Procedures
Status Code Entry Chart