Message Display Entry Chart - Xerox 8825 Service Manual

Table 1 Status Code Entry Chart
Status Description
Code
LL-58 Power On Self Test
No Extra "Return Value" from the
RAP Operating System. Reboot
(Power off / Power On).
LL-60 Power On Self Test NVM
No Checksum fault
RAP Record the existing NVM val-
ues. Run diagnostic [0360] to
reset NVM to the default val-
ues. Manually restore the
required NVM values.
LL-61 Power On Self Test revision
No level fault
RAP Power the printer up in diag-
nostics and run [0360] to reset
NVM to default values.
LL-89 This is a Firmware problem
No This is a firmware problem.
RAP Press power off (0) then
power on (1). If problem per-
sists, replace the firmware.
LL-90 Overtoned fault
Over- Toner concentration of the
toned developer material is too high.
Fault
RAP
LL-91 Undertoned fault
Under- Toner concentration of the
toned developer material is too low.
Fault
RAP
U1-01 Media counter error
No Print counter is disconnected.
RAP
8825/8830 Printer
Components BSD PL
Ref Ref
Install the Control PL
EPROM 1.1A
Main PWB (A3)
PL
1.1A
Cartridge drive motor 3.1 PL
(A22MOT1) 9.7 1.1A
Cartridge home sensor 9.7 PL
(A22Q2) 9.3 9.9
Toner sensor (A22Q1)
Main PWB (A3)
Cartridge drive motor 9.7 PL
(A22MOT1) 9.9
Cartridge home sensor PL
(A22Q2) 1.1A
Toner sensor (A22Q1)
Main PWB (A3)
Media counter BSD PL
Main PWB (A3) 3.1 1.3
PL
1.1A

Message Display Entry Chart

Table 1 Message Display Entry Chart
MESSAGE DIS- CAUSE
PLAYED
PRINTER IS WARM- No fuser heat
ING UP (Continuously
displayed)
ADJUSTING THE Toner
PRINT QUALITY (Con- problem
tinuously displayed)
PLEASE CLOSE THE Drawer
MEDIA DRAWER X switch is open.
(Refer to Note)
PLEASE CLOSE THE Cut sheet
CUT SHEET FEED shelf
SHELF switch
open.
PLEASE CLOSE THE Front door inter-
FRONT DOOR lock switch (S21)
is open.
PLEASE CLOSE THE Top cover interlock
TOP DOOR switch
open.
PLEASE CLOSE THE Cutter cover inter-
CUTTER DRAWER lock switch (S1) is
open.
NVM FAULT CALL FOR Corrupted data in
ASSISTANCE NVM.
Re-feed Roll 1 Re-feed
problem.
Re-feed Roll 2 Re-feed
problem.
Re-feed Roll 3 Re-feed
problem.
Flashing 1, 2, 3, 4, 5, 6 Copier
or 7 power on self-test.
UNABLE TO CALI- The sensor did not
BRATE TONER SEN- calibrate when the
SOR code [0921-6] was
entered.
TONER FAULT CALL Excessive
FOR ASSISTANCE sensed problem.
01/02
Status Code Entry Chart, Message Display Entry
1-11
CLEARANCE PROCEDURE
- - -
dispense - - -
X read Refer to the display on the control panel
and follow the clearance procedure.
feed Refer to the display on the control panel
interlock and follow the clearance procedure.
(S29) is
Refer to the display on the control panel
and follow the clearance procedure.
Refer to the display on the control panel
(S26) is and follow the clearance procedure.
Refer to the display on the control panel
and follow the clearance procedure.
Press power off (0) then power on (1). If
problem persist run diagnostic program
[0363] or [0360]. If problem persist
replace the Control EPROMS.
roll 1 Re-feed the media. If necessary, press
power off (0) then power on (1).
roll 2 Re-feed the media. If necessary, press
power off (0) then power on (1).
roll 3 Re-feed the media. If necessary, press
power off (0) then power on (1).
failed Press power off (0) then power on (1). If
problem persists,
svc.8830prt.2974.
Press power off (0), then power on (1).
If problem persists, go to LL-91 Under-
toned Fault RAP.
toner Press power off (0), then power on (1).
If problem persists, go to LL-90 Over-
toned Fault RAP.
Service Call Procedures
BSD
Ref
BSD
10.1
BSD
9.3
BSD
7.1
BSD
1.2
BSD
1.2
BSD
1.2
BSD
1.2
BSD
7.2
BSD
7.3
BSD
7.4
go to
BSD
9.7
BSD
9.7