Revision History - Omron SYSDRIVE 3G3HV SERIES User Manual

A manual revision code appears as a suffix to the catalog number on the front cover of the manual.
The following table outlines the changes made to the manual during each revision. Page numbers refer to the
previous version.
Revision code
1 August 1996
2 April 1997
3 April 2000

Revision History

Cat. No. I515-E1-3
Date
Original production
Page 1-2: Inverter model list updated. "Enclosed wall-
mounted type" replaced with "NEMA1 type."
Page 1-4: Low noise and harmonic countermeasure
information clarified.
Page 2-4: Dimensions added for the new models.
Page 2-5: "Enclosed Wall-mounted Type" replaced with
"NEMA1 Type."
Page 2-7: Terminals U, V, and W replaced with T1 (U),
T2 (V), and T3 (W) respectively.
Pages 2-10, 2-11: Terminals and connections changed
for the 200-V Class and 400-V Class tables. New models
reflected.
Page 2-12: Names for the three-phase terminals
changed.
Page 2-13: Names for the three-phase terminals
changed. Notes added. New models reflected.
Pages 2-14, 2-15: Terminal names changed and new
models added. New wire sizes and tightening torque
added.
Pages 2-16 to 2-20: Information for Wiring on the Input
Side of Main Circuit and Wiring on the Output Side of
Main Circuit changed.
Page 2-22: Second harmonic frequency corrected.
Information in Causes of Harmonics Generation cor-
rected at the bottom of the page.
Page 2-23: Last sentence of DC/AC Reactors corrected.
Note added.
Preliminary pages: Order changed and safety information added.
Pages 1-6, 2-33, 3-2, 3-5, 3-7, 3-16, 3-20, 3-21, 3-22, 3-38 to 3-50, 3-52, 3-56, 3-69,
3-71, 3-74, 3-80, 3-84, 5-11: Notes changed or added.
Page 1-6, 3-2: Explanation for "Operation Mode Selection Key" changed.
Page 1-7: Information on new functions added.
Pages 2-6, 2-15, 3-20, 3-31, 3-55, 5-5: Graphics changed or added.
Pages 2-7, 3-2, 4-13: "Cautions and Warnings" information changed.
Page 2-9: Information on wiring changed.
Pages 2-14, 3-5, 3-13, 3-21, 3-31, 3-38 to 3-50, 3-56, 3-62, 3-72, 3-74, 5-11, 5-13, 6-5
to 6-8: Changes made to tables.
Pages 2-20 to 2-22, 5-17 to 5-19: Major changes.
Page 2-24: Changes made to information on cable length. Information on single-phase
motors added.
Page 3-8: Information on operation modes added after table.
Page 3-23, 4-2: Information added to introduction.
Page 3-58: Setting range for n030 changed.
Page 3-61: Setting range for n039 changed.
Page 3-65: Information for external baseblock command changed.
Page 3-66: Information on PID control added.
Page 3-75: Default setting for n052 changed.
Page 3-76: Setting range for n053 changed.
Page 3-83: "Motor Rated Slip" changed to "Slip Compensation Gain."
Page 3-84: Information for n112, n113, and n114 changed.
Page 4-4: Information on connection error added.
Page 4-12: Information added.
Pages 5-3, 5-4: "IP00" changed to "IP10."
Index: Index removed.
Revision code
Revised content
Pages 2-24, 2-25: Terminal names changed. New model
information reflected.
Page 2-26: Inverter models added to the input trans-
former table.
Page 2-27: New model information reflected. Information
on connecting Braking Units in parallel added. Informa-
tion removed from Wire Size and Solderless Terminals at
the bottom of the page.
Pages 3-3, 3-9: Terminal names changed.
Page 3-44: Note added.
Page 3-58: New model information reflected in the table.
Page 3-72: Notes added.
Pages 4-2, 4-8: Terminal names changed.
Pages 4-3, 4-4: Cause and action for the heat sink over-
heat and Inverter overload added to.
Page 4-12: Inverter overload information added.
Pages 5-2, 5-3: Specifications completely updated.
Pages 5-5, 5-9, 5-10: "Control Unit" corrected to "Braking
Unit."
Pages 5-9, 5-10: New models added.
Pages 5-15, 5-18: Noise Filter models added.
Page 6-5: New models added.
Page 6-13: Note added.
R-1