Table of Contents
Advertisement
Pitch
Pan Depth
= (+) value
Original Pitch
Left
<
<
<
< < <<<<<< >>>>>> > >
Louder
042: Scratch
This effect is applied by recording the input signal and
moving the modulation source. It simulates the sound of
scratches you can make using a turntable.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
+
Rec Control
Right
D-mod
D
-mod
Envelope Control
Input
Envelope Select
D
-mod
Scratch
Selects the modulation source
a
Off...Tempo
Source
for simulation control
Sets the speed of the response
b Response
0...100
to the Scratch Src
Selects whether the start and
Envelope
D-mod,
end of recording is controlled
Select
Input
via the modulation source or
the input signal level
c
Selects the modulation source
that controls recording when
Src
Off...Tempo
Envelope Select is set to D-mod
Sets the recording start level
d Threshold
0...100
when Envelope Select is set to
Input
Sets the speed of the response
e Response
0...100
to the end of recording
Always On,
Selects how a dry sound is
f
Direct Mix
Always Off,
mixed
Cross Fade
Dry, 1 : 99...
Sets the balance between the
Wet/Dry
99 : 1, Wet
effect and the dry input
Selects a modulation source for
g
Src
Off...Tempo
Wet/Dry
Sets the modulation amount
Amt
–100...+100
for Wet/Dry
a: Scratch Source
b: Response
The Scratch Source parameter enables you to select the
modulation source that controls simulation. The value of the
modulation source corresponds to the playback position.
The Response parameter enables you to set the speed of the
response to the modulation source.
Doppler - Pitch / Pan Depth
Pan Depth
= (–) value
Pitch Depth
Center
Right
Pan Depth
>
>
>
Volume
Louder
Wet / Dry
Direct
Scratch
Mix
Scratch
Wet / Dry
p.317
p.317
p.317
p.317
p.317
p.317
p.317
Modulation and Pitch Shift (Mod./P.Shift)
Start
Playback Position
Recorded Sound
Scratch Source
Scratch!
JS X
D
-mod
JS+Y
– Max
JS–Y
etc...
Zero
c: Envelope Select
c: Src
d: Threshold
When Envelope Select is set to D-mod, the input signal will
be recorded only when the modulation source value is 64 or
higher.
When Envelope Select is set to Input, the input signal will
be recorded only when its level is over the Threshold value.
The maximum recording time is 2,730msec. If this is
exceeded, the recorded data will start being erased from the
top.
e: Response
This parameter enables you to set the speed of the response
to the end of recording. Set a smaller value when you are
recording a phrase or rhythm pattern, and set a higher value
if you are recording only one note.
f: Direct Mix
With Always On, a dry sound is usually output. With
Always Off, dry sounds are not output. With Cross Fade, a
dry sound is usually output, and it is muted only when
scratching.
Set Wet/Dry to Wet to use this parameter effectively.
043: Grain Shifter
This effect cuts extremely short samples ("grains") from the
input signal waveform and plays them repeatedly, giving a
mechanical character to the sound.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
+
Grain Shifter
Right
LFO
D
-mod
Trigger
Sets the duration of the grain
Duration
0...100
Selects the source that will
Src
Off...Tempo
modulate the duration of the
a
grain
Sets the amount by which the
Amt
–100...+100
grain duration will be
modulated
Selects the modulation source
b LFO Sync Src Off...Tempo
that will reset the LFO
LFO Sample
Sets the frequency at which the
0.02...20.00
Cycle [Hz]
grain will be switched
Selects a modulation source for
c
Src
Off...Tempo
LFO speed
–20.00...
Sets the modulation amount of
Amt
+20.00
LFO speed
Scratch Source
End
+ Max
Zero
+ Max
Wet / Dry
Sample Cycle
Wet / Dry
p.318
p.318
317
Advertisement
Table of Contents
