Table of Contents
Advertisement
Sequencer mode
Recording will end, and the location will return to the point
at which you begin recording.
If you press the PAUSE switch instead of the SEQUENCER
START/STOP switch, recording will pause. When you press
the PAUSE switch once again, recording will resume. When
you are finished, press the SEQUENCER START/STOP
switch to stop recording.
Overdub
Select this method when you wish to add data to a
previously-recorded track.
With this method, the newly recorded musical data is added
to the existing data.
When you perform overdub recording on a previously-
recorded track, the newly recorded data will be added to the
previously-recorded data.
It is best to select this mode if you will be recording
additional control data, recording a drum pattern, or
recording the tempo in the master track. With this mode,
data can be added without erasing the existing performance
data.
1. Use Track Select to choose the track that you want to
record.
2. Set the Recording Setup to Overdub.
3. For the rest of the procedure, please see steps 3–5 of
"Overwrite."
Manual Punch In
Select this method when you wish to use the SEQUENCER
REC/WRITE switch or a foot switch to re-record selected
portions of a previously-recorded track.
While the song is playing, you can press the SEQUENCER
REC/WRITE switch or a connected pedal switch at the
desired location to start or stop recording. With this method,
the musical data previously on the track is overwritten by
the newly recorded data.
1. Use Track Select to select the track that you want to
record.
2. Set the Recording Setup to Manual Punch In.
3. In "Location," specify a location several measures ear-
lier than the point at which you wish to begin record-
ing.
4. Press the SEQUENCER START/STOP switch.
Playback will begin.
5. At the point at which you wish to begin recording,
press the SEQUENCER REC/WRITE switch.
Recording will begin. Play the keyboard and operate
controllers such as the joystick to record your performance.
6. When you finish recording, press the SEQUENCER
REC/WRITE switch.
Recording will end (playback will continue).
Note: Instead of pressing the SEQUENCER REC/WRITE
switch in steps 5 and 6, you can use a foot switch connected
to the ASSIGNABLE SWITCH jack.
Set the Global P2: Controllers page Foot Switch Assign to
Song Punch In/Out.
138
7. Press the SEQUENCER START/STOP switch.
Playback will stop, and you will return to the location that
you specified in step 3.
Auto Punch In
Select this method when you wish to automatically re-
record selected portions of a previously-recorded track.
Recording will occur only over the specified area, rewriting
it with the newly recorded data.
First you must specify the area that will be re-recorded.
Then recording will automatically start and end within the
specified area. With this method, the musical data
previously on the track is overwritten by the newly recorded
data.
1. Use Track Select to choose the track that you want to
record.
2. Set the Recording Setup to Auto Punch In.
3. In "M (Auto Punch In Start Measure), "M (Auto Punch
In End Measure)" specify the area that you wish to
record.
For example, if you specify M005–M008, recording will
occur only from measure 5 to measure 8.
4. In "Location," specify a location several measures
before the point at which you wish to begin recording.
5. Press the SEQUENCER REC/WRITE switch, and then
press the SEQUENCER START/STOP switch.
Playback will begin.
When you reach the starting location you specified in step 3,
recording will begin. Play the keyboard and operate
controllers such as the joystick to record your performance.
When you reach the ending location you specified in step 3,
recording will end. (Playback will continue.)
6. Press the SEQUENCER START/STOP switch.
Playback will stop, and you will return to the location you
specified in step 4.
Auto Punch In Start Measure
Auto Punch In End Measure
When Recording Setup is set to Auto Punch In, specify the
measures at which recording will start and end.
Loop All Tracks
Select this method when you wish to repeatedly record a
specified area of a track, and continue adding data. This is
suitable for creating drum patterns, etc.
If Multi REC is checked, this parameter will not be
available.
This method lets you continue recording as you add musical
data.
The specified region can be recorded repeatedly. This is ideal
when recording drum phrases, etc.
Use Track Select to select the track that you want to record.
1. Set the Recording Setup to Loop All Tracks.
2. If Multi REC is checked, it will not be possible to select
Loop All Tracks.
[M001...M999]
[M001...M999]
Advertisement
Table of Contents
