Korg M50-88 Parameter Manual page 27

Mode
Programs Prog P1: Basic/Ctrls
Combinations Combi P1: Controllers
Songs Seq P1: Controllers
When using SW1/2 for AMS or Dmod, the default settings
are SW1 Mod.(CC#80) and SW2 Mod.(CC#81).
For an example, see "Dynamic modulation (Dmod)" on
page 72 of the Owner's manual.
For a complete list of the possible assignments, see "SW1/2
Assignments" on page 382.
Note: If you wish to keep these settings after the power is
turned off, you must save the Program, Combination, or
Song (see OM page 88).
1–7b: Realtime Control Knob Assign
Here you can select the functions (mainly types of control
change) that are assigned to knobs 1–4 when Control
Assign (0–8b) Realtime Control B mode is selected. (See
"Realtime Control Knobs 1–4 Assignments" on page 383)
The functions you assign here are active when you use the
CONTROL ASSIGN REALTIME CONTROL switch to select
B, and operate knobs 1–4.
Knob1–B [Off, ..., MIDI CC#95, CC#102...119]
Knob2–B [Off, ..., MIDI CC#95, CC#102...119]
Knob3–B [Off, ..., MIDI CC#95, CC#102...119]
Knob4–B [Off, ..., MIDI CC#95, CC#102...119]
Setting the functions of Realtime Control B mode
knobs 1–4
When the Control Surface CONTROL ASSIGN is set to
RealTime Control B mode, the four knobs on the right
function as Realtime knobs 1–4.
These can perform a number of different functions, such as
modulating sounds or effects, adjusting effects send levels,
and so on.
Each Program, Combination, and Song stores its own
settings for what the knobs will do.
When using the sliders for AMS or Dmod, it's important to
understand that creating an assignment is a two-step
process. First, you assign the knob to send a MIDI controller,
such as Knob Mod.1 (CC#17). Second, you assign that MIDI
controller to modulate one or more Program or effects
parameters.
For the first part of the above, use the mode's Controllers
Setup page (See "Setting the functions of SW1 and SW2,"
above).
The default assignments for knobs 1–4 are Knob Mod.1
(CC#17), Knob Mod.2 (CC#19), Knob Mod.3 (CC#20), and
Knob Mod.4 (CC#21), respectively. For a complete list of the
possible assignments, see "Realtime Control Knobs 1–4
Assignments" on page 383.
Here's an example of how to set up knob 1 to control a
Program's filter and amp EG attack time:
1. Press the MODE PROG switch to enter Program mode.
2. Access the P1: Basic/Ctrls– Controllers Setup page.
Press the PAGE SELECT switch to access Page Select, and
choose "P1 Basic/Ctrls."
3. Press the Realtime Control Knob Assign "Knob 1–B"
popup button, and choose F/A Attack (CC#73).
4. Press the CONTROL ASSIGN REALTIME CONTROL
switch to select B. (the LED B will light)
PROG P1: Basic/Ctrls (Basic/Controllers) 1–7: Controllers Setup
Page
5. Operate knob 1 to control the EG attack for the filter
and amp.
Note: If you wish to keep these settings after the power is
turned off, you must save the Program, Combination, or
Song (see OM page 88).
▼1–7: Menu Command
• 0: Write Program ☞p.73
• 1: Exclusive Solo ☞p.73
For more information, please see "Program: Menu
Command" on page 73.
19