D Command Table - Icom IC-7700 Instruction Manual

14
CONTROL COMMAND
D D Command table (continued)
Command Sub command
14 18 + Level data [CONTRAST] setting (0=max.
19 + Level data [BRIGHT] setting
15 01
02
11
12
13
14
15
16
16 02
12
22
32
40
41
42
43
44
45
46
47
48
4C
4D
4E
4F
50
53
19 00
1A 00
01
02
Description
CCW to 255=max. CW)
(0=max. CCW to 255=max. CW)
Read squelch condition
Read S-meter level
Read RF power meter
Read SWR meter
Read ALC meter
Read COMP meter
Read V meter
D
Read I meter
D
Send/read Preamp setting
(0=OFF; 1=preamp 1;
2=preamp 2)
Send/read AGC selection
(0=OFF; 1=Slow; 2=Mid; 3=Fast)
Send/read noise blanker setting
(0=OFF; 1=ON)
Send/read Audio peak filter set-
ting for CW mode
(APF type=SHARP: 0=OFF;
1=320 Hz; 2=160 Hz; 3=80 Hz,
APF type=SOFT: 0=OFF;
1=WIDE; 2=MID; 3=NAR)
Send/read noise reduction setting
(0=OFF; 1=ON)
Send/read auto notch setting
(0=OFF; 1=ON)
Send/read repeater tone setting
(0=OFF; 1=ON)
Send/read tone squelch setting
(0=OFF; 1=ON)
Send/read speech compressor
setting (0=OFF; 1=ON)
Send/read monitor setting
(0=OFF; 1=ON)
Send/read VOX function setting
(0=OFF; 1=ON)
Send/read Break-in function set-
ting (0=OFF; 1=semi break-in;
2=full break-in)
Send/read manual notch setting
(0=OFF; 1=ON)
Send/read VSC setting
(0=OFF; 1=ON)
Send/read Manual AGC setting
(0=OFF; 1=ON)
Send/read DIGI-SEL setting
(0=OFF; 1=ON)
Send/read twin peak filter setting
(0=OFF; 1=ON)
Send/read dial lock function set-
ting (0=OFF; 1=ON)
Send/read RX antenna connector
setting (0=OFF; 1=ON)
Read the transceiver ID
Send/read memory contents (see
p. 14-9 for details)
Send/read band stacking register
contents (see p. 14-9 for details)
Send/read memory keyer con-
tents (see p. 14-9 for details)
Command Sub command
1A 03
04
050001
050002
050003
050004
050005
050006
050007
050008
050009
050010
050011
050012
050013
050014
050015
050016
050017
050018
050019
050020
050021
050022
14-4
Description
Send/read the selected filter width
(SSB, CW, PSK: 0=50 Hz to
40=3600 Hz; RTTY: 0=50 Hz to
31=2700 Hz; AM: 0=200 Hz to
49=10 kHz)
Send/read the selected AGC time
constant (0=OFF, 1=0.1/0.3 sec.
to 13=6.0/8.0 sec.)
Send/read SSB RX HPF/LPF
(HPF: 0=Through, 1=100 to
20=2000, LPF: 5=500 to
24=2400, 25=Through)
Send/read SSB RX Tone (Bass)
level (0 =–5 to 10=+5)
Send/read SSB RX Tone (Treble)
level (0=–5 to 10=+5)
Send/read AM RX HPF/LPF
(HPF: 0=Through, 1=100 to
20=2000, LPF: 5=500 to
24=2400, 25=Through)
Send/read AM RX Tone (Bass)
level (0 =–5 to 10=+5)
Send/read AM RX Tone (Treble)
level (0=–5 to 10=+5)
Send/read FM RX HPF/LPF
(HPF: 0=Through, 1=100 to
20=2000, LPF: 5=500 to
24=2400, 25=Through)
Send/read FM RX Tone (Bass)
level (0 =–5 to 10=+5)
Send/read FM RX Tone (Treble)
level (0=–5 to 10=+5)
Send/read CW RX HPF/LPF
(HPF: 0=Through, 1=100 to
20=2000, LPF: 5=500 to
24=2400, 25=Through)
Send/read RTTY RX HPF/LPF
(HPF: 0=Through, 1=100 to
20=2000, LPF: 5=500 to
24=2400, 25=Through)
Send/read PSK RX HPF/LPF
(HPF: 0=Through, 1=100 to
20=2000, LPF: 5=500 to
24=2400, 25=Through)
Send/read SSB TX Tone (Bass)
level (0 =–5 to 10=+5)
Send/read SSB TX Tone (Treble)
level (0=–5 to 10=+5)
Send/read AM TX Tone (Bass)
level (0 =–5 to 10=+5)
Send/read AM TX Tone (Treble)
level (0=–5 to 10=+5)
Send/read FM TX Tone (Bass)
level (0 =–5 to 10=+5)
Send/read FM TX Tone (Treble)
level (0=–5 to 10=+5)
Send/read SSB TX bandwidth for
wide (see p. 14-10 for details)
Send/read SSB TX bandwidth for
mid. (see p. 14-10 for details)
Send/read SSB TX bandwidth for
narrow (see p. 14-10 for details)
Send/read speech level
(0=0% to 255=100%)