Chapter 9
Troubleshooting the Cisco IOS XR Software
Verifying the System Interfaces
Perform the following steps to verify the system interfaces.
Step 1
Enter the show platform command to verify that all nodes are in the "IOS-XR RUN" state:
RP/0/RP0/CPU0:router# show platform
Node
-----------------------------------------------------------------------------
0/1/SP
0/1/CPU0
0/2/SP
0/2/CPU0
0/3/SP
0/3/CPU0
0/RP0/CPU0
0/RP1/CPU0
0/SM0/SP
0/SM1/SP
Enter the show ipv4 interface brief command to verify IP address configuration and protocol status:
Step 2
RP/0/RP0/CPU0:router# show ipv4 interface brief
Interface
POS0/1/0/0
POS0/1/0/1
POS0/1/0/2
POS0/1/0/3
POS0/1/0/4
POS0/1/0/5
POS0/1/0/6
POS0/1/0/7
POS0/1/0/8
POS0/1/0/9
POS0/1/0/10
POS0/1/0/11
POS0/1/0/12
POS0/1/0/13
POS0/1/0/14
POS0/1/0/15
POS0/2/0/0
POS0/2/0/1
POS0/2/0/2
POS0/2/0/3
TenGigE0/3/0/0
TenGigE0/3/0/2
MgmtEth0/RP0/CPU0/0
Type
PLIM
MSC(SP)
N/A
MSC
16OC48-POS/DPT
MSC(SP)
N/A
MSC
16OC48-POS/DPT
MSC(SP)
N/A
MSC
16OC48-POS/DPT
RP(Active)
N/A
RP(Standby)
N/A
FC/S(SP)
N/A
FC/S(SP)
N/A
IP-Address
unassigned
unassigned
unassigned
unassigned
unassigned
unassigned
unassigned
unassigned
unassigned
unassigned
unassigned
unassigned
unassigned
unassigned
unassigned
unassigned
10.10.1.101
unassigned
unassigned
unassigned
unassigned
unassigned
unassigned
Cisco CRS-1 Series Carrier Routing System Getting Started Guide
Interfaces Not Coming Up
State
Config State
IOS-XR RUN
PWR,NSHUT,MON
IOS-XR RUN
PWR,NSHUT,MON
IOS-XR RUN
PWR,NSHUT,MON
IOS-XR RUN
PWR,NSHUT,MON
IOS-XR RUN
PWR,NSHUT,MON
IOS-XR RUN
PWR,NSHUT,MON
IOS-XR RUN
PWR,NSHUT,MON
IOS-XR RUN
PWR,NSHUT,MON
IOS-XR RUN
PWR,NSHUT,MON
IOS-XR RUN
PWR,NSHUT,MON
Status
Protocol
Shutdown
Down
Shutdown
Down
Shutdown
Down
Shutdown
Down
Shutdown
Down
Shutdown
Down
Shutdown
Down
Shutdown
Down
Shutdown
Down
Shutdown
Down
Shutdown
Down
Shutdown
Down
Shutdown
Down
Shutdown
Down
Shutdown
Down
Shutdown
Down
Down
Down
Shutdown
Down
Shutdown
Down
Shutdown
Down
Shutdown
Down
Shutdown
Down
Shutdown
Down
9-21