Grizzly G0451 Instruction Manual page 22

box 7: (figure 17)
O. rip Fence Body .......................................... 1
p. Blade guard/dust hood ............................. 1
Q. push stick .................................................. 1
r. dust Collection hose support .................... 1
o
Q
figure 17. Box 7 contents.
box 7 cont.: (figure 18)
S. toolbox ....................................................... 1
—Flat Belt 15 x 880mm.............................. 1
—riving Knife ............................................ 1
—Arbor Wrench 30mm .............................. 1
—hose Clamps 2 ⁄
1
—Feet M16-2 x 100 .................................... 4
—Arbor Wrench 8mm ................................ 1
figure 18. Box 7 contents continued.
in the event that any nonproprietary parts are
missing (e.g. a nut or a washer), we would be
glad to replace them, or for the sake of expedi-
ency, replacements can be obtained at your local
hardware store.
-20-
Qty
p
r
Qty
" .................................. 2
2
component hardware (not shown)
push handle M12-1.75 x 12 (sliding table) ....... 1
Flat Washer 12mm (push handle) .................... 1
t-nut M12-1.75 (push handle) ........................... 1
set screw M6-1.0 x 12 (small table) ................ 2
Cap screw M10-1.5 x 20 (small table) ............. 2
lock Washer 10mm (small table) ..................... 2
Flat Washer 10mm (small table) ...................... 2
Cap screw M10-1.5 x 20 (large table) ............. 4
lock Washer 10mm (large table) .................... 4
Flat Washer 10mm (large table) ...................... 4
set screw M6-1.0 x 12 (large table) ................ 4
Cap screw M10-1.5 x 30 (support Brace) ......... 4
Flat Washer 10mm (support Brace) .................. 4
lock Washer 10mm (support Brace) ................ 4
hex nut M10-1.5 (support Brace) ..................... 2
hex Bolts M6-1 x 25 (scale Bar) ....................... 3
Flat Washers 6mm (scale Bar) ......................... 3
lock Washers 6mm (scale Bar) ........................ 3
hex nuts M6-1 (scale Bar)................................ 3
lock handles M10-1.5 x 12 (rip Fence Body) .. 2
Knob M10-1.5 x 70 (rip Fence Body) ............... 1
Adjustable ring w/set screw (r rail) ............... 1
end Washer 8mm (r rail) ................................ 1
lock Washer 8mm (r rail) ............................... 1
Cap screw M8-1.25 x 16 (r rail) ...................... 1
Adjustable handle M12-1.75 x 55 (Crosscut).... 1
Flat Washer 12mm (Crosscut table) ................ 1
t-nut M12-1.75 (Crosscut table) ....................... 1
t-nut M8-1.25 (Crosscut Brace) ........................ 2
Knob M8-1.25 x 50 (Crosscut Brace, Fence) .... 3
Flat Washer 8mm (Crosscut Brace) .................. 2
Center stud M8-1.25 x 10 (Crosscut Fence) ..... 1
Fiber Washer 8mm (Crosscut Fence) ............... 1
t-Bolt M8-1.25 x 60 (Crosscut Fence) ............... 1
t-nut M8-1.25 (Crosscut Fence) ....................... 2
Knob M8-1.25 (Crosscut Fence) ........................ 1
Knob M8-1.25 x 25 (Crosscut Fence) ................ 1
Flat Washer 8mm (Crosscut Fence) .................. 1
Block (Crosscut Fence) ..................................... 1
Cap screw M8-1.25 x 35 (Crosscut Fence) ...... 1
lock Washer 8mm (Crosscut Fence) ................ 1
Button hd Cap screw M8-1.25 x 40 (guard) .... 1
Flat Washer 8mm (guard) ................................. 1
g0451 14" sliding table saw
Qty