We are proud to offer the Model g0493 14" sliding table saw. this machine is part of a grow- please write to us at the address below: ing grizzly family of fine woodworking machinery.
MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0493 14" 10 HP 3-PHASE SLIDING TABLE SAW Product Dimensions: Weight................................1804 lbs. Length/Width/Height........................186 x 133-1/4 x 49 in.
Page 6
The information contained herein is deemed accurate as of 12/14/2007 and represents our most recent product specifications. Model G0493 PAGE 2 OF 3 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. g0493 14" sliding table saw...
Page 7
The information contained herein is deemed accurate as of 12/14/2007 and represents our most recent product specifications. Model G0493 PAGE 3 OF 3 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. g0493 14" sliding table saw...
Page 11
W. scoring blade on button—starts the scor- ing blade. note: The main saw blade must be ON for the scoring blade to start. X. main blade on button—starts the main saw blade. g0493 14" sliding table saw...
(570) 546-9663. like all machines there is danger associ- no list of safety guidelines can be complete. ated with the model g0493. accidents are every shop environment is different. always frequently caused by lack of familiarity or consider safety first, as it applies to your failure to pay attention.
Become familiar with these terms for assembling, adjusting or operating this machine. your safety is very important to us at grizzly! arbor: Metal shaft extending from the drive non-through cut: a sawing operation that mechanism, to which saw blade is mounted.
6. hardwired locking disconnect switch. amperage draw grounding the Model g0493 features 220/440v motors in the event of an electrical short, grounding that are prewired for 220v and draw the following reduces the risk of electric shock. the grounding...
440v conversion kit. turn the dial on the main motor overload relay to 9a. the Model g0493 can be rewired for 440v opera- tion. the necessary parts for this procedure can be purchased by calling our customer service at (800) 523-4777 and ordering part #p04510014a.
3: setup setup safety unpacking the Model g0493 was carefully packed when it left our warehouse. if you discover the machine is damaged after you have signed for delivery, this machine presents please immediately call Customer Service at serious injury hazards (570) 546-9663 for advice.
Page 21
Washer 10mm (large table) ....4 some hardware/fasteners on the inventory Flat Washer 10mm (large table) ..... 4 list may arrive pre-installed. check mount- ing locations on main components before assuming inventory list items are missing. -19- g0493 14" sliding table saw...
(an addi- tional person may need to adjust the t-bolt spacing to allow the sliding table to fit.) figure 22. sliding table upside down. -23- g0493 14" sliding table saw...
Page 26
10. rotate the table lock 180˚ to unlock the slid- ing table. the sliding table is locked in place when the table lock is in the position shown in figure 29. figure 27. dust port access hole to access center t-bolt. -24- g0493 14" sliding table saw...
Page 27
M10-1.5 x 20 cap screws, four 10mm figure 34. Checking with a straightedge. lock washers, and four 10mm flat wash- ers, as shown in figure 32. note: The cap screws will be tightened during a later step. -25- g0493 14" sliding table saw...
Page 28
36, to mount it. (the top the tables. do not tighten the hex nuts at this of the hex bolts slide into the scale bar.) time. figure 36. attaching the scale bar. figure 38. installing the round rail. -26- g0493 14" sliding table saw...
Page 29
24. Move the blade arbor tilt to 0˚ and raise it as far as it will go. -27- g0493 14" sliding table saw...
Page 30
To adjust the mounting position of the round rail, use the hex nuts (on the round rail studs) that are on both sides of the tables. -28- g0493 14" sliding table saw...
Page 31
Blade vertical adjustment figure 46. adjusting the riving knife. 36. tighten the center bolt to secure the riving scoring Blade knife in position. horizontal adjustment figure 48. scoring blade adjustment controls. -29- g0493 14" sliding table saw...
Page 32
50. When installed correctly, this ring will prevent the fence from contacting the blade. adjustable ring w/set screw figure 52. installing the adjustable handle. figure 50. securing the adjustable ring. -30- g0493 14" sliding table saw...
Page 33
54. installing the crosscut table brace. 52. (optional) if needed, slide the edge shoe and hold down clamp into the table t-slot, and tighten the respective knob/handle. position where necessary. (the front cover picture shows these items installed.) -31- g0493 14" sliding table saw...
Page 34
55. attach the blade guard/dust hood to the riv- ing knife with the M8-1.25 x 40 button head cap screw and 8mm flat washer. (the blade do not operate the model g0493 without an guard/dust hood Must be installed.) adequate dust collection system. this saw creates substantial amounts of wood dust 56.
When using a phase converter, con- nect the manufactured power leg to the S terminal to prevent damage (see Page 13). figure 63. emergency stop switch #2. r s t ground figure 61. Main terminal box. -33- g0493 14" sliding table saw...
Page 36
18. Close the orange blade guard and move exchange wires r & t in the power con- the sliding table back to the center of the nection box. machine. depress the #1 emergency stop switch. -34- g0493 14" sliding table saw...
66. Move the blade guard back to its original position, and move the sliding table back to center. riving Knife figure 66. re-adjusting the riving knife. -38- g0493 14" sliding table saw...
(the the underside of the test piece. if there is internal blade guard is held in place with a chip out, make the adjustments necessary to magnet.) match the kerfs. -39- g0493 14" sliding table saw...
— to use the sliding table, read the instruc- the Model g0493 has the capability of rip cut- tions titled “rip Cutting w/sliding table.” ting full size panels (figure 70). the sliding table removes the burden of sliding a large and heavy —...
Page 43
Micro-adjust lock Knob Micro-adjust Knob lock lever horizontal figure 74. rip fence positions. figure 76. rip fence micro-adjusting controls. push down the lock lever, then perform the cutting operation. -41- g0493 14" sliding table saw...
(figure 79). the Model g0493 can crosscut full size panels with the fence in the forward or rear position, although it is easier to load full size panels with the crosscut fence mounted in the forward posi- tion (see figure 77).
Page 45
Fence to Blade" on page 53 if necessary. take all the necessary safety precautions, then perform the cutting operation. set either flip stop to the desired width-of-cut. note: Extend the crosscut fence slide if the workpiece is more than 74". -43- g0493 14" sliding table saw...
0˚ to 90˚ cuts. figure 83. example of miter cutting operation. once all the necessary safety precautions have been taken, perform the cutting opera- tion. figure 82. Fence set-up for 90˚ to 135˚ cuts. -44- g0493 14" sliding table saw...
6: maintenance cleaning always disconnect power to the machine before Cleaning the Model g0493 is relatively easy. performing maintenance. vacuum excess wood chips and sawdust, and failure to do this may wipe off the remaining dust with a dry cloth. use...
5. Motor bearings are at fault. 5. test by rotating shaft; rotational grinding/loose shaft requires bearing replacement. 6. start delay module is at fault. 6. adjust to correct delay; replace module. 7. Motor is at fault. 7. test/repair/replace. -49- g0493 14" sliding table saw...
Page 52
Clean out dust and gr -50- g0493 14" sliding table saw...
95, and noting the amount of deflection. scoring Motor figure 96. replacing the scoring motor belt. Close and secure the motor cabinet door. figure 95. Checking belt deflection. -51- g0493 14" sliding table saw...
90°. —if the blade tilt pointer shows an incorrect tilt, adjust it by loosening the mounting screws, rotating the pointer until it points to 90°, then tightening the mounting screws. -52- g0493 14" sliding table saw...
99. Measuring gap between the table and the blade. 11. tighten the table mounting bolts and replace the access plates. rotate the blade 180° and slide the table with the measuring device to position B. -53- g0493 14" sliding table saw...
5–8. — if both measurements are within ⁄ " then you are finished with this procedure. figure 102. Fence adjustment test piece. -55- g0493 14" sliding table saw...
PSB64M CAP SCREW M10-1.5 X 25 P04930417 HOSE CLAMP 2-1/2" PSS03M SET SCREW M6-1 X 8 PSBS23M BUTTON HD CAP SCR M8-1.25 X 25 PSS05M SET SCREW M5-.8 X 10 PW01M FLAT WASHER 8MM -67- g0493 14" sliding table saw...
PLASTIC WASHER 13MM PRP32M ROLL PIN 6 X 40 PSS103M SET SCREW M12-1.75 X 50 P04930514 LOCATE BLOCK PSS42M SET SCREW M8-1.25 X 50 PR03M EXT RETAINING RING 12MM PRP70M ROLL PIN 5 X 18 -68- g0493 14" sliding table saw...