Denon AVR-3310CI Owner's Manual page 46

Making Detailed Settings (Manual Setup)
Setting items
Zone Rename
1. Use ui to select the zone name (MAIN ZONE, ZONE2 or ZONE3) you
Change the display title of want to change, then press
each zone to one you prefer. o p
2. Use to set the cursor to the character you want to change.
3. Use ui to change the character, then press
• Up to 10 characters can be input.
• You can change the character type when you press
character input.
• The types of characters that can be input are as shown below.
GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GLower case charactersH abcdefghijklmnopqrstuvwxyz
GSymbolsH ! " # $ % & ' ( ) * + , - . / : ; < = > ? @ [ \ ] ˆ _ ` { | } ˜
GNumbersH 0123456789
4. Repeat steps 1 ~ 3 to change the display name.
Trigger Out 1 When Setting for Zone (MAIN ZONE / ZONE2 / ZONE3)
n
Trigger out is activated through linkage to the power of the zone set to
Select the condition for
"ON".
activating Trigger Out 1 for
the input source, surround
n When Setting for Input Source
mode, etc.
Activate trigger out when the input source set to "ON" is selected.
See "TRIGGER OUT jacks"
Valid for the zone set to "ON" with "When Setting for Zone".
(vpage 22) for more
information on trigger out.
When Setting for Surround Mode
n
Trigger Out 2
Activate trigger out when the surround mode set to "ON" is selected.
As with "Trigger Out 1",
Valid when the "MAIN ZONE" set to "ON" with "When Setting
select the condition for
for Zone" is selected, and when the input source set to "ON" with
activating Trigger Out 2.
"When Setting for Input Source" is selected.
• ON : Activate trigger on this mode.
• – – – : Do not activate trigger on this mode.
Remote ID 1 / 2 / 3 / 4
Set when you operate
When using the AVR-3310CI with only the included main remote
another DENON AV amplifier
control unit (RC-1118), use Remote ID "1" (default).
with the remote control unit
When using the included sub remote control unit (RC-1121) and a
of the AVR-3310CI. Match
separately sold remote control unit (RC-7000CI, etc.), this function
the remote control unit you
can be used. Match the ID setting of the remote control unit and the
are using with the remote ID
receiver.
of the AVR-3310CI.

Main remote control
operation buttons
Setting contents
ENTER
p or .
ENTER
.
[SEARCH]
(Space)
:Displaying the menu
Cancel the menu
Setting items
232C Port
Set when using an external
controller or two-way remote
control connected to the RS-
232C terminal.
during
Dimmer
Adjust display brightness of
the receiver.
Setup Lock
Protect settings from
inadvertent change.
Maintenance Mode
Used when receiving
maintenance from a DENON
service engineer or custom
installer.
:Moves the cursor
:Confirm the setting
(Up/Down/Left/Right)
Setting contents
Serial Control : Set when using an external controller.
2Way Remote : Set when using a 2-way remote control unit.
When using a DENON two-way remote control (RC-7000CI or RC-
7001RCI, sold separately), set to "2Way Remote".
NOTE
When setting to "2Way Remote", you can not use the RS-232C connector
as an external controller.
Bright : Normal display brightness.
Dim : Reduced display brightness.
Dark : Very low display brightness.
OFF : Turns the display off.
OFF : Turn protection off.
ON : Turn protection on.
• When "Setup Lock" is set to "ON", the settings listed below can no
longer be changed. Also, "SETUP LOCKED!" is displayed if you attempt
to operate related settings.
· GUI menu operations · Dynamic Volume
· RESTORER · Channel Level
· Audio/Video Adjust · Audio Delay
· MultEQ · Input Mode
· Dynamic EQ
• When canceling the setting, set "Setup Lock" to "OFF".
NOTE
Only use this function if so instructed by a DENON serviceperson or
installer.
:Return to previous menu