Denon AVR-3310CI Owner's Manual page 40

Making Detailed Settings (Manual Setup)
Making the Audio Settings (Audio Setup)
Make settings for audio playback.
Setting items
EXT. IN SW Level +15dB : This is the recommended level.
+10dB / +5dB / 0dB : Select the level according to the player being
Set the playback level of the
used.
analog subwoofer signals in-
put from the external input
terminals (EXT. IN).
2ch Direct/Stereo Setting : Select the method for setting the speakers used in the 2-channel
direct and stereo playback modes.
Make speaker settings for 2-
• Basic : The settings at "Speaker Setup" (vpage 34) are applied.
channel mode playback.
• Custom : Make separate settings for 2-channel.
Front : Set the front speaker size.
• Large : Use of a large speaker that can adequately playback low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
If "Speaker Configuration" – "Subwoofer" (vpage 34) is set to
"No", the setting is automatically set to "Large".
Subwoofer : Set the presence of a subwoofer.
• Yes : Use a subwoofer.
• No : Select when a subwoofer is not connected.
If "Speaker Configuration" – "Subwoofer" (vpage 34) is set to
"No", the setting is automatically set to "No". If the "Front" setting is
"Small", the setting is automatically "Yes".
SW Mode : Select low range signal to be reproduced by subwoofer.
• LFE : When the "2ch Direct/Stereo" – "Front" setting is set to "Large",
the LFE signal alone is output from the subwoofer. Also, when the "2ch
Direct/Stereo" – "Front" setting is set to "Small", the front channel low
range signal is added to the LFE signal output from the subwoofer.
• LFE+Main : The front channel low range signal is added to the LFE signal
output from the subwoofer.
This can be set when "2ch Direct/Stereo" – "Subwoofer" is set to
"Yes".

Main remote control
operation buttons
Default settings are underlined.
Setting contents
:Displaying the menu :Moves the cursor
Cancel the menu (Up/Down/Left/Right)
Setting items
2ch Direct/Stereo Crossover : Outputs at below set frequency, each speaker's bass signal
output from the subwoofer.
(Continued)
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz
• This can be set when "2ch Direct/Stereo" – "Subwoofer" is set to
"Yes".
• If the "2ch Direct/Stereo" – "Front" setting is "Large" and the "SW
Mode" setting is "LFE", "Full Band" is displayed and the setting cannot
be made.
Distance FL / Distance FR : Select the speaker.
• 0.0ft ~ 60.0ft (12.0ft) / 0.00m ~ 18.00m (3.60m) : Set the distance to
the speaker.
Set so that the difference between the front left speaker and front
right speaker distances is 6.0 m (20.0 ft) or less.
Level FL / Level FR : Select the speaker.
• –12.0dB ~ +12.0dB (0dB) : Adjust the level of each channel.
Auto Surround Mode ON : Memorize settings. Automatically play with the last used surround
mode.
Make setting for memorizing
OFF : Do not memorize settings. Surround mode does not change
surround mode setting for
according to input signal
each input signal type.
• The auto surround mode function lets you store in the memory the
surround mode last used for playing the four types of input signals listed
below.
q Analog and PCM 2-channel signals
w Dolby Digital and DTS 2-channel signals
e Dolby Digital and DTS multi-channel signals
r Multi-channel signals other than Dolby Digital and DTS (PCM etc.)
• When playing in the PURE DIRECT, the surround mode does not change
even if the input signal is changed.
EQ Customize Audyssey Byp. L/R : Set when not using the "Audyssey Byp L/R"
equalizer.
Set so that unused equalizer
• Used : Use.
settings are not displayed
MULTEQ • Not Used : Do not use.
when is pressed.
Set so that "Audyssey Byp. L/R" settings can be made when
Audyssey™ Auto Setup procedure is performed.
Equalizer settings for which
"Not Used" is set with the
Quick Select function cannot
be stored and called out.
:Confirm the setting
Setting contents
:Return to previous menu