Denon AVR-3310CI Owner's Manual page 33

s Audyssey Auto Setup Preparations
around items indicate the default setting.
STEP1 Preparation
Perform the following settings if adjustments, etc., are required for
the speaker environment you're using.
If you do not need to perform the following settings, or have already
completed them, select "Auto Setup Start" and then press
Proceed to " STEP2 ".
Change the Amplifier Assignment (Amp Assign)
The signal output from the SURR.BACK/AMP ASSIGN speaker
terminal of the AVR-3310CI can be switched to match your speaker
environment (vpage 34 "Amp Assign").
1
Press to select
ui
"Amp Assign", then
press ENTER .
2
Press to select Amp Assign Mode, then press
o p
RETURN .
Normal : The surround back channel audio signals are
output.
: The ZONE2 audio signals are output.
ZONE2
ZONE3 : The ZONE3 audio signals are output.
: The ZONE2 / ZONE3 monaural audio signals are
ZONE2/3-MONO
output.
Front A Bi-Amp : The bi-amp audio signals are output. Set this for
bi-amp playback of the front A speakers.
Front B Bi-Amp : The bi-amp audio signals are output. Set this for
bi-amp playback of the front A speakers.
: The front height channel audio signals are output.
Front Height
• When you are using surround back speakers with ZONE2/ZONE3,
set to "ZONE2" or "ZONE3".
• You can set in the same way as described in "Amp Assign" on page
34.
Main remote control
operation buttons
NOTE
Since "Amp Assign" of AVR-3310CI is set to "ZONE2" by default,
audio is not output from the surround back speakers. When using the
surround back speakers with MAIN ZONE, change the "Amp Assign"
setting to "Normal".
Set the channel to be measured (Channel Select)
•
Front
ENTER
.
The front speaker to be measured can be selected ahead of time here.
• Subwoofer, Surround Back
If you set the channels you will not use beforehand, those channels
will not be measured. Therefore, you can save an amount of time
commensurate with that which would have been taken to measure
those channels.
1
Press to select
ui
"Channel Select",
then press ENTER
2
Press to select a channel, press
ui
the item, and then press
Front
n
A
: The sound is output from front speakers A when
measuring the front speakers.
: The sound is output from front speakers B when
B
measuring the front speakers.
: The sound is output simultaneously from front speakers
A +B
A and B when measuring the front speakers.
Subwoofer, Surround Back
n
Measure : Measure the selected channel.
Skip : Skip the selected channel and do not measure.
When "Amp Assign" is set to "Normal", only then is "Surround Back"
displayed.
:Displaying the menu :Moves the cursor
Cancel the menu (Up/Down/Left/Right)
Make the Optimal Speaker Settings, and Correct the Room Acoustics (Audyssey™ Auto Setup)
.
to select
o p
RETURN
.
:Confirm the setting
d Perform Audyssey Auto Setup
• Audyssey Auto Setup detects the presence of each speaker and
automatically calculates the speaker size, channel level, distance and
crossover frequency settings. In addition, acoustical distortions are
corrected within the listening area.
• When measuring begins, a test tone is output from each speaker.
• Position and connect all speakers before commencing Audyssey
Auto Setup.
STEP2 Speaker Detection
1
Press ui to select "Auto Setup Start", then press
ENTER .
2
Select "Measure"
and then press
ENTER
.
3
Once all the speakers have been detected, check the
results of detection of the connected speakers.
4
Press ui to
select "Next 1
Measurement", then
press ENTER .
Press u to select "Retry", and when you press
b
at the main listening position starts again.
:Return to previous menu
ENTER
, measuring
See overleaf
0