Denon AVR-3310CI Owner's Manual page 104

GAudioH
Symptom Cause / Countermeasure
No sound is produced • When playing monaural audio sources, select a surround mode
from center speaker. other than "STANDARD" (Dolby/DTS Surround).
No sound is produced • Set the surround mode to a mode for surround playback.
from surround
speakers.
No sound is produced • Check that the surround back speaker's power amplifier
from surround back assignment is set to "Normal".
speaker. • Set the surround back speakers to something other than
"None".
• Set "Surround Parameter" – "Surround Back" to something
other than "OFF".
• Set the surround mode to the surround playback mode.
No sound is produced • Turn on the subwoofer's power.
from subwoofer. • Set the subwoofer to "Yes".
• Check the subwoofer connections.
• Increase the subwoofer's channel level.
DTS sound is not • Set the Blu-ray disc/DVD player's audio output setting to "Bit-
output. stream". For details, refer to the Blu-ray disc/DVD player's
operating instructions.
• Use a DTS-compatible Blu-ray disc player/DVD player.
• Set the decode mode to "Auto" or "DTS".
Dolby TrueHD, DTS- • Make HDMI connections.
HD, Dolby Digital Plus • Set the Blu-ray disc/DVD player's audio output setting to "Bit-
audio is not output. stream". For details, refer to the Blu-ray disc/DVD player's
operating instructions.
• Use a DTS-compatible Blu-ray disc player.
GControl dock for iPodH
Symptom Cause / Countermeasure
iPod cannot be • Connect to the terminal to which "iPod dock" was assigned and
played. switch the input source.
• Check the iPod connections.
• Plug the control dock for iPod's AC adapter into a power outlet.
Communications with the AVR-3310CI are not possible unless
the AC adapter is plugged in.
0
GVideoH
Symptom
Page
No picture appears. • Check the connections of the AVR-3310CI's video output
69
terminals and the TV's input terminals.
• Make the proper input setting for the input terminals of the TV
69, 70
connected to the AVR-3310CI.
• Cancel the PURE DIRECT mode.
• High definition (1080i/720p) and progressive (480p/576p) video
34
signals are not down-converted. Set the player to interlace
(480i/576i) signals.
34
• Check the "Video Select" setting.
Picture cannot be • The REC OUT video terminal does not have a video conversion
72
recorded. function, so use a video cable to input video signals, an S-Video
cable to input S-Video signals.
69, 70
DVDs cannot be • This is not a malfunction. Most movie software includes copy
–
copied on a VCR. prevention signals and cannot be copied.
34
GUI is not displayed. • Set "Format" according to the format (NTSC or PAL) of the TV
13
being used.
35
–
GHDMIH
Symptom
–
HDMI audio signals • Set "Audio Out" to "AMP" to output HDMI audio signals from
49
are not output from the speakers.
speakers.
14
–
No picture appears • Check the connection of the HDMI connectors.
with HDMI • Select the input source assigned to the HDMI terminal at
connections. "HDMI".
–
• Connect a monitor that is compatible with copyright protection
(HDCP).
• Check that the output format (HDMI FORMAT) of the connected
player, etc., matches the TV's compatible input formats.
No sound is output • Set "Audio Out" to "TV" to output HDMI audio signals from the
Page
from the monitor TV.
24, 47
connected with HDMI
connections.
16
When performing the • Set "HDMI Control" to "OFF". When you only want to operate the
–
following operations power on/off each device, set "Power Off Control" to "OFF".
on a connected
device, AVR-3310CI
has the same
operations.
• Power ON/OFF
• Switching audio
output devices
• Adjust volume
• Switch input source
Cause / Countermeasure
Cause / Countermeasure
Page
14, 15
–
70
–
48
18
–
42
Page
36
14
27 , 46
14
14, 15
36
36