User Constants - Omron VARISPEED G7 Instruction Manual

User Constants

Factory settings are given in the following table. These setting are for a 200 V Class Inverter of 0.4 kW set
to factory set control method (open-loop vector control).
No. Name
Language selection for digital
A1-00
operator display
A1-01 Constant access level
A1-02 Control method selection
A1-03 Initialize
A1-04 Password
A1-05 Password setting
A2-01 to
User setting constants
A2-32
b1-01 Reference selection
b1-02 Operation method selection
b1-03 Stopping method selection
b1-04 Prohibition of reverse operation
Operation selection for setting E1-
b1-05
09 or less
b1-06 Read sequence input twice
Operation selection after switching
b1-07
to remote mode
Run command selection in pro-
b1-08
gramming modes
Zero speed level (DC injection
b2-01
braking starting frequency)
b2-02 DC injection braking current
b2-03 DC injection braking time at start
b2-04 DC injection braking time at stop
Magnetic flux compensation vol-
b2-08
ume
b3-01 Speed search selection
b3-02 Speed search operating current
b3-03 Speed search deceleration time
b3-05 Speed search wait time
b4-01 Timer function ON-delay time
b4-02 Timer function OFF-delay time
b5-01 PID control mode selection
b5-02 Proportional gain (P)
b5-03 Integral (I) time
b5-04 Integral (I) limit
b5-05 Derivative (D) time
b5-06 PID limit
b5-07 PID offset adjustment
b5-08 PID primary delay time constant
PID output characteristics selec-
b5-09
tion
b5-10 PID output gain
Table 10.5 User Constants
Fac-
Set-
tory No.
ting
Setting
*1
b5-11 PID reverse output selection
1
Selection of PID feedback com-
2 b5-12
mand loss detection
PID feedback command loss detec-
*1
b5-13
2
tion level
PID feedback command loss detec-
0 b5-14
tion time
0 b5-15 PID sleep function operation level
0 b5-16 PID sleep operation delay time
Acceleration/deceleration time for
- b5-17
PID reference
1 b6-01 Dwell frequency at start
1 b6-02 Dwell time at start
0 b6-03 Dwell frequency at stop
0 b6-04 Dwell time at stop
0 b7-01 Droop control gain
1 b7-02 Droop control delay time
0 b8-01 Energy-saving mode selection
0 b8-02 Energy-saving gain
0.5 b8-03 Energy-saving filter time constant
50 b8-04 Energy-saving coefficient
Power detection filter time con-
0.00 b8-05
stant
0.50 b8-06 Search operation voltage limiter
0 b9-01 Zero-servo gain
*2 *3
b9-02 Zero-servo completion width
2
*2
C1-01 Acceleration time 1
100
2.0 C1-02 Deceleration time 1
0.2 C1-03 Acceleration time 2
0.0 C1-04 Deceleration time 2
0.0 C1-05 Acceleration time 3
0 C1-06 Deceleration time 3
1.00 C1-07 Acceleration time 4
1.0 C1-08 Deceleration time 4
100.0 C1-09 Emergency stop time
0.00 C1-10 Accel/decel time setting unit
Accel/decel time switching fre-
100.0 C1-11
quency
S-curve characteristic time at
0.0 C2-01
acceleration start
S-curve characteristic time at
0.00 C2-02
acceleration end
S-curve characteristic time at
0 C2-03
deceleration start
S-curve characteristic time at
1.0 C2-04
deceleration end
User Constants
Fac-
Name tory
Setting
0
0
0
1.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.05
0
*4
0.7
*5
0.50
*6
20
0
5
10
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
1
0.0
0.20
0.20
0.20
0.00
Set-
ting
19
10-