Omron VARISPEED G7 Instruction Manual page 138

Name
Con-
stant
Num-
Display
ber
Mid. output
frequency 2
E1-11
Mid
Frequency
B
Mid. output
Set only to fine-adjust V/f for the
frequency
output range. Normally, this setting
voltage 2
E1-12
is not required.
Mid
Voltage B
Base
voltage
E1-13
Base
Voltage
* 1. These are values for a 200 V Class Inverter. Values for a 400 V Class Inverter are double.
* 2. The factory setting will change when the control method is changed. (Open-loop vector 1 factory settings are given.)
* 3. E1-11 and E1-12 are disregarded when set to 0.0.
* 4. E1-13 is set to the same value as E1-05 by autotuning.
* 5. The setting range is 0 to 66.0 for open-loop vector control 2.
Motor Setup: E2
User constants for motor 1 are shown in the following table.
Name
Con-
stant
Display
Number
Motor rated Sets the motor rated current in
current 1 A units.
These set values will become
the reference values for motor
E2-01
protection, torque limits and
Motor Rated
torque control.
FLA
This constant is automatically
set during autotuning.
Motor rated Sets the motor rated slip in
slip Hz units.
These set values will become
E2-02 the reference values for slip
Motor Rated
compensation.
Slip
This constant is automatically
set during autotuning.
Motor no-
Sets the motor no-load cur-
load current
rent in 1 A units.
E2-03
This constant is automatically
No-Load
set during autotuning.
Current
Number of
Sets the number of motor
motor poles
poles.
E2-04
This constant is automatically
Number of
set during autotuning.
Poles
Motor line-
Sets the motor phase-to-phase
to-line resis-
resistance in Ω units.
tance
E2-05
This constant is automatically
Term Resis-
set during autotuning.
tance
Setting
Description
Range
0.0 to
400.0
*5
0.0 to
255.0
*1
0.0 to
255.0
*1
Setting Factory
Description
Range Setting
0.32 to
1.90 A
6.40
*2
0.00 to
2.90 Hz
20.00
0.00 to
1.20 A
1.89
*3
2 to 48 4 poles
0.000
9.842
to
65.000
Control Methods
Change
Open
Factory during
V/f Loop
Setting Opera-
V/f with Vec-
tion
PG tor
1
0.0 Hz
No A A A
*3
0.0 V
No A A A
*3
0.0 V
No A A Q
*4
Control Methods
Change
Open
during
V/f Loop
Opera-
V/f with Vec-
tion
PG tor
1
No Q Q Q
*1
No A A A
*1
No A A A
*1
No No Q No
No A A A
Ω
*1
User Constant Tables
MEMO-
Open
BUS
Flux Loop
Page
Regis-
Vec- Vec-
ter
tor tor
2
6-
A A 30AH
107
6-
A A 30BH
107
6-
Q Q 30CH
107
MEMO
Open
BUS
Flux Loop
Page
Regis-
Vec- Vec-
ter
tor tor
2
6-49
Q Q 30EH 6-
105
6-
103
A A 30FH
6-
105
6-
A A 310H
105
6-
Q Q 311H
105
6-
A A 312H
105
5-
33