Instructions And Technical Norms - Ariston 801 Instructions For Installation, Use, Maintenance

INSTRUCTIONS AND TECHNICAL NORMS

The purchaser pays for the appliance's installation, which
must be carried out by qualified personnel only, in conform-
ity with national regulations in force and any provisions
emitted by local authorities or bodies responsible for public
health, and in accordance with the specific manufacturer
indications contained in this manual. The manufacturer is
responsible for the product's conformity to the relevant con-
struction directives, laws and regulations in force at the time
the product is first commercialised. The designer, installer
and user are each exclusively responsible, in their respective
fields, for knowing and observing the legal requirements and
technical regulations concerning the design, installation, oper-
ation and maintenance of the appliance.
Any reference to laws, regulations or technical specifications
contained in this manual is purely for information purposes;
any new laws introduced or modifications to existing laws
are not in any way binding on the manufacturer towards third
parties. It is necessary to ensure that the power supply net-
work to which the product is connected complies with the EN
50160 norm (under penalty of warranty invalidation). Relative
to France, ensure that installation complies with the NFC 15-
100 norm. The tampering of product integral parts and/or sup-
plied accessories invalidates the warranty.
FIELD OF APPLICATION
This appliance is intended for hot water production for domes-
tic use or similar, at temperatures below boiling point.
The appliance must be hydraulically connected to a domestic
water supply line and to a power supply network.
Air ducts may be used for the entry and discharge of pro-
cessed air.
It is forbidden to use of the appliance for uses other than
those specified. Any alternative use of the appliance con-
stitutes improper use and is prohibited; in particular, the ap-
pliance may not be used in industrial cycles and/or installed
in environments exposed to corrosive or explosive materials.
The manufacturer shall not be held liable for any damage due
to faulty installation, improper use or uses deriving from be-
haviour that is are not reasonably predictable, and incomplete
or careless implementation of the instructions contained in
this manual.
OPERATING PRINCIPLE
The efficiency of a heat pump operation is measured by the
Coefficient of Performance (COP), i.e. the ratio between the
energy supplied to the appliance (in this case, the heat trans-
ferred to the water to be heated) and the electrical energy
used (by the compressor and the appliance's auxiliary devic-
es). The COP varies according to the type of heat pump and
to its relative conditions of operation.
For example, a COP value equal to 3 indicates that for every 1
kWh of electrical energy used, the heat pump supplies 3 kWh
of heat to the medium to be heated, of which 2 kWh are ex-
tracted from the free source.
PACKAGING AND SUPPLIED ACCESSORIES
The appliance is protected by expanded polystyrene foam pads
and a cardboard box on the outside; all materials are recyclable and
eco-friendly.
The following accessories are included:
- Instruction manual and warranty documents;
- 2 x 1/2" dielectric unions;
28 / EN
- Overpressure protection device (8 bar);
This accessory does not correspond to the NF EN 1487 standard,
it must not be used with products sold and installed in countries
where this standard is mandatory.
- Condensate water discharge pipe connector and safety valve for
waste water;
- 1 wall mounting bracket;
- 2 screws, 2 wall plugs and 2 rubber pads for the wall bracket (ad-
ditional wall plugs for the 110 l and 150 l versions);
- 2 pipe adapters for air ducting (110/125 mm);;
- Energy label and product sheet.
PRODUCT CERTIFICATIONS
The CE marking applied to the appliance certifies that it complies
with the essential requirements of the following European Directives:
- 2014/35/EU on electrical safety (LVD) (EN/IEC 60335-1; EN/IEC
60335-2-21; EN/IEC 60335-2-40);
- 2014/30/EC on electromagnetic compatibility (EMC) (EN 55014-1
EN 55014-2; EN 61000-3-2; EN 61000-3-3);
- RoHS3 (2015/863) concerning restrictions on the use of particular
hazardous substances in electrical and electronic appliances (EN
63000);
- Regulation (EU) No. 814/2013 relating to ecodesign (no. 2014/C
207/03 - transitional methods of measurement and calculation).
The performance inspection is carried out according to the following
technical standards:
- EN 16147;
- CAHIER DE CHARGE_103-15/D Chauffe-eau Thermodynamiques
pour la marque NF électricité performance;
- Sound power level measurement is carried out according to EN
12102-2
This product conforms to:
- Regulation (EC) No. 1907/2006 (REACH);
- Regulation (EU) No. 812/2013 (labelling);
- (Italian) Ministerial Decree No. 174 of 06/04/2004 that transposes
European Directive no. 98/83 on water quality;
- Radio Equipment Directive (RED): ETSI 301489-1,
ETSI 301489-17.
- The radio frequency band in which the radio equipment operates
is 2,4 GHz and the maximum power of the transmitted signal is <
20 dBm
IDENTIFICATION OF THE APPLIANCE
The main information for identifying the appliance is contained
on the adhesive data plate located on the water heater casing.
A Model
B Tank capacity
C Serial no.
D Power supply voltage, frequency,
maximum absorbed power
E Max./min. pressure of the refrigeration circuit
F Marks and symbols
G Absorbed power – heating element mode
H Maximum tank pressure
I Max./min. power in heat pump mode
L Tipo di refrigerante e carica
M Maximum tank pressure
N GWP global warming potential /
Quantity of fluorinated greenhouse gases