Table of Contents
Advertisement
Setting by Local CQ
1 Press and hold [ ].
The destination selection screen appears. This screen also
appears when selecting [Destination Select] in the Digital
Function Menu.
2 Select [Local CQ] and press [ENT].
CQCQCQ is set to [TO].
Setting by Gateway CQ
1 Press and hold [ ].
The destination selection screen appears. This screen also
appears when selecting [Destination Select] in the Digital
Function Menu.
2 Select [Gateway CQ] and press [ENT].
The repeater list selection screen appears.
3 Select the destination repeater and press [ENT].
The repeater is set to [TO].
Setting by Individual
1 Press and hold [ ].
The destination selection screen appears. This screen also
appears when selecting [Destination Select] in the Digital
Function Menu.
2 Select [Individual] and press [ENT].
The Callsign list appears.
3 Select the Callsign and press [ENT].
The selected Callsign is set to [TO].
Setting by Reflector
1 Press and hold [ ].
The destination selection screen appears. This screen also
appears when selecting [Destination Select] in the Digital
Function Menu.
2 Select [Reflector] and press [ENT].
The Reflector menu item appears.
3 Select the following items and press [ENT].
[Use Reflector]: If your repeater is currently linked
to a reflector, select [Use Reflector] and press [ENT].
[CQCQCQ] is set to [TO]. Then press [PTT] to transmit
your digital voice signal to the reflector.
[Link to Reflector]: If you want to link the repeater to a
reflector, or you want to change to another reflector, select
[Link to Reflector] and press [ENT]. Input the reflector's
type (REF/DCS/XRF/XLX), number (000 to ZZZ) and
module (A to Z), and press [ENT]. A link command
(example: [REF030CL]) is set to [TO]. Then press [PTT]
to link the repeater to the reflector. Up to 5 reflectors you
linked before are shown when you select [Link to Reflector]
again.
[Unlink Reflector]: If you want to link the repeater
to another reflector, be sure to unlink currently linked
reflector. Select [Unlink Reflector] and press [ENT].
[_______U] is set to [TO]. Then press [PTT] to unlink the
repeater from the reflector.
[Echo Test]: You can verify how well your digital voice
signal is getting into the system. Select [Echo Test] and
press [ENT]. Then [_______E] is set to [TO]. Then press
[PTT] to transmit your digital voice signal to the system.
After releasing [PTT], echo back will be sent back from the
repeater.
[Reflector Info.]: You can send the reflector information
command. Select [Reflector Info.] and press [ENT]. Then
[_______I] is set to [TO]. Then press [PTT] to transmit the
reflector information command. After releasing [PTT], ID
will be sent from the repeater.
Note:
¡ To use a hotspot (simplex DV access point), you can store the
hotspot's frequency and other information in the Hotspot List
(Menu No.230) for using the DR mode Reflector menu above.
Please refer to page No.16-16 "HOTSPOT LIST" for details.
Setting by Call History
1 Press and hold [ ].
The destination selection screen appears. This screen also
appears when selecting [Destination Select] in the Digital
Function Menu.
2 Select [Call History] and press [ENT].
The Callsign list appears.
3 Select the destination Callsign and press [ENT].
The selected Callsign is set to [TO].
Setting by Direct Input (URCALL)
1 Press and hold [ ].
The destination selection screen appears. This screen also
appears when selecting [Destination Select] in the Digital
Function Menu.
2 Select [Direct Input(URCALL)] and press [ENT].
The direct input screen appears.
3 Enter the destination Callsign and press [ENT].
The destination Callsign is set to [TO].
Note:
¡ When entering the destination Callsign by direct input
(URCALL), the route setting is not automatically set. Please
be sure to set the route setting by [Route Select] in the Digital
Function Menu then.
Setting EMR
1 Press and hold [ ].
The destination selection screen appears. This screen also
appears when selecting [Destination Select] in the Digital
Function Menu.
2 Select [EMR] and press [ENT].
The EMR is set.
CHECKING THE CALLSIGN SETTING
You can check transmission settings of DV/DR mode before
transmission.
1 Select [CS Setting] in the Digital Function Menu.
The confirmation screen appears.
2 Press [A/B].
Each press switches between name display and Callsign
display.
16-8
Advertisement
Table of Contents
