Troubleshooting; Dimensional Drawings; Technical Data - Theben thePixa P360 24V KNX UP WH Manual

L Activate safety mode: A password must be created in
order to activate the mode. This password protects the
following parameters or functions:
- Entering actual temperature
- Light level value per zone
- Installation height
- Detection sensitivity
- Teach-in
- Factory settings
- Firmware update
- Zone editing
L The safety password must consist of 6 characters: A-Z,
0-9.
L The safety mode as well as the safety password can also
be activated or defined in the ETS application. The safety
mode can be edited subsequently in the app.

9. Troubleshooting

Fault Cause
Light does not switch Lux value is set too low; detector set on semi-
on or switches off automatic; light was switched off manually via
during presence and push button or with remote control; person not
darkness within detection area; obstruction(s) interrupting
detection; time delay set too short.
Light is switched on Lux value set too high; light was recently set
in case of presence manually by button (wait 30 min in switching
despite sufficient mode); performing a firmware update.
brightness
Light is constantly Interruption of the auxiliary voltage. After resto-
switched on despite no ration of voltage, the detector is back in normal
one is present operation.
Light does not switch Wait for time delay to elapse (different time delays
off, or light switches on can be configured); optical sources of interference
spontaneously when in the detection area: reflections of light influen-
no one is present ces, larger screens in the detection area, moving
objects such as curtains when the window is open.
Smartphone/tablet BLE not activated in the smartphone/tablet; inter-
cannot be connected ruption of the auxiliary voltage.
with the detector

10. Technical data

Operating voltage:
KNX bus voltage:
Auxiliary voltage current
consumption:
Minimum load:
Brightness setting range:
Lighting time delay:
Standby dimming value light: 1 – 25% of the dimming value
Standby time light:
HVAC switch-on delay:
HVAC time delay:
HVAC standby runtime:
HVAC standby value:
KNX medium:
Protection rating:
Protection class:
230–240 V AC, 50 Hz (226920X);
20–35 V DC (226921X)
30 V DC
230 V AC: day mode 4 mA (0.9 W); night
mode 7 mA (1.6 W)
24 V DC: day mode 38 mA; night mode
67 mA
KNX auxiliary voltage (30 V DC): day mode
30 mA; night mode 54 mA
10 mA
5 – 3000 lux/measurement off
0 s – 60 min
0 s – 60 min/permanently on
0 s – 120 min
0 s – 120 min
0 s – 120 min
0 – 255
TP1-256
IP 20 in accordance with EN 60529
II subject to designated installation
Operating temperature:
Recommended installation
height:
Detection angle:
Detection area:
Pollution degree:
Rated impulse voltage:
Software:
Radio frequency/transmis-
sion power:
Theben AG herewith declares that this type of radio installation complies with
Directive 2014/53/EU. The complete text of the EU Declaration of Conformity
is available at the following Internet address:
www.theben.de/red-konformitaet
Cleaning and service
Only use a dry, soft cloth to clean the device surface.
†
Do not use any cleaning agents or solvents.
†
Disposal
Dispose of device in environmentally sound manner
†
(electronic waste).

11. Dimensional drawings

12. Open source software components
(OSS)
A list of the open source components used can be found on
the Internet at the following link:
https:/ /www.theben.de/OSS
–5 °C ... +45 °C
2.5 – 4.5 m (minimum height ≥ 2.5 m)
360° horizontal
15.5 x 11 m I 171 m moving radially/
2
tangentially
2
4 kV
Class A
BLE 2.4 GHz Class 2 (2.5 mW)
9