1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Fire Alarms
  5. NOTIFIER FireWarden-100-2
  6. Instruction manual

Honeywell NOTIFIER FireWarden-100-2 Instruction Manual

Fire alarm control panel
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Fire Alarm Control Panel
FireWarden-100-2
FireWarden-100-2E
Instruction Manual
A
Document 52778
11/04/2005
Rev:
P/N 52778:A
ECN 06-086

Advertisement

Table of Contents
loading

Related Manuals for Honeywell NOTIFIER FireWarden-100-2

Summary of Contents for Honeywell NOTIFIER FireWarden-100-2

  • Page 1 Fire Alarm Control Panel FireWarden-100-2 FireWarden-100-2E Instruction Manual Document 52778 11/04/2005 Rev: P/N 52778:A ECN 06-086...
  • Page 2 Fire Alarm System Limitations While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance! An automatic fire alarm system—typically made up of Heat detectors do not sense particles of combustion and smoke detectors, heat detectors, manual pull stations, audible alarm only when heat on their sensors increases at a predeter- warning devices, and a fire alarm control panel with remote mined rate or reaches a predetermined level.
  • Page 3 Acclimate Plus™, HARSH™, NIS™, Notifier Integrated Systems™, NOTI•FIRE•NET™, and ONYXWorks™ are all trademarks; and FlashScan®, NION®, NOTIFIER®, ONYX®, UniNet®, VeriFire®, and VIEW® are all registered trademarks of Honeywell International Inc. Echelon® is a registered trademark and LonWorks™ is a trademark of Echelon Corporation. ARCNET® is a registered trademark of Datapoint Corporation. Microsoft® and Windows® are registered trademarks of the Microsoft Corporation.
  • Page 4 Brief description of content you think should be improved or corrected • Your suggestion for how to correct/improve documentation Send email messages to: FireSystems.TechPubs@honeywell.com Please note this email address is for documentation feedback only. If you have any technical issues, please contact Technical Services. FireWarden 100-2/E — P/N 52778:A 11/04/2005...

  • Page 5: Table Of Contents

    Table of Contents Section 1: Product Description ..................... 11 1.1: Features and Options ...........................11 1.2: Specifications...............................12 1.2.1: Current Availability...........................14 1.3: Controls and Indicators..........................15 1.4: Circuits.................................16 1.5: Digital Alarm Communicator/Transmitter ....................16 1.6: Components ..............................17 1.6.1: Intelligent Addressable Detectors......................17 1.6.2: Intelligent Addressable Modules .......................17 1.6.3: Addressable Device Accessories .......................18 1.7: Optional Modules ............................18 1.8: Accessories ..............................18...
  • Page 6 Table of Contents 3.6.5: System Setup .............................77 3.6.6: Verify Loop ............................90 3.6.7: History ...............................91 3.6.8: Walktest .............................92 3.6.9: Option Modules ..........................93 3.6.10: Password Change...........................113 3.6.11: Clear Program ..........................113 3.6.12: Program Check ..........................114 3.7: Maintenance Programming Level......................116 3.7.1: Disable Point............................117 3.7.2: History .............................117 3.7.3: Program Check ..........................118 3.7.4: Walktest ............................120 3.7.5: System..............................120...
  • Page 7 Table of Contents 4.22.10: Annunciators..........................143 4.22.11: Phone Line...........................143 4.22.12: Central Station ..........................144 4.22.13: Service Terminal..........................145 4.22.14: Printer/PC ............................145 4.22.15: Print .............................146 4.22.16: Time-Date............................148 Section 5: Central Station Communications ..............149 5.1: Transmittal Priorities ..........................152 Section 6: Remote Site Upload/Download................154 6.1: Downloading Program..........................154 6.1.1: Security Features ..........................155 6.2: Downloading Initiated at a Service Terminal ....................156...
  • Page 8 It is imperative that the installer understand the requirements of the Authority Having Jurisdiction (AHJ) and be familiar with the standards set forth by the following regulatory agencies. • Underwriters Laboratories Standards • NFPA 72 National Fire Alarm Code Before proceeding, the installer should be familiar with the following documents. NFPA Standards NFPA 72 National Fire Alarm Code NFPA 70 National Electrical Code...
  • Page 9 CAUTION! HIGH VOLTAGE TRANSFORMER 2 TRANSFORMER 1 Figure 1.1 Basic System Connections FireWarden 100-2/E — P/N 52778:A 11/04/2005...
  • Page 10 Peripheral Devices and Their Documents: ACM-8R AFM-16AT & ACS Series Doc. #15342 AFM-32A 15842 Doc. #15048 ACS (EIA-485) Annunciators LDM-32 AFM-16A Doc. #15885 Doc. #15207 TERM (EIA-485) FDU-80 Annunciators Doc. #51264 SLC Loop Addressable Devices and SLC Wiring Doc. #52304 Battery Connector CHG-75 Charger CHG-120 Charger...

  • Page 11: Section 1: Product Description

    NOTE: The Notifier FireWarden-100-2 FACP (Fire Alarm Control Panel) will be referred to as the NFW2-100. Unless otherwise specified, the term NFW2-100 is used in this manual to refer to both the NFW2-100 (120 VAC version) and the NFW2-100E (240 VAC version) FACPs.

  • Page 12: Specifications

    Product Description Specifications • Communication Confirmation (Kissoff) LED • Touchtone/Rotary dialing • Programmable Make/Break Ratio • EIA-232 Printer/PC interface (variable baud rate) • 80-character LCD display (backlit) • Real-time clock/calendar with daylight savings time control • History file with 1,000 event capacity •...
  • Page 13 Specifications Product Description Battery (Lead Acid Only) - J9 Maximum Charging Circuit: Normal Flat Charge - 27.6 VDC @ 0.80 amp Maximum Battery Charger Capacity: 18 Amp Hour (NFW2-100 cabinet holds maximum of two 18 Amp Hour batteries. For greater than 25 Amp Hour up to 120 Amp Hour batteries, use the CHG- 75 or CHG-120 Battery Charger and NFS-LBB Battery Box.

  • Page 14: 1: Current Availability

    Product Description Specifications EIA-485 (TERM) or EIA-232 (ACS) - TB8 EIA-485 Terminal Mode annunciator connections: Terminal 1 (Out +), 2 (In +), 3 (Out -), 4 (In -) EIA-232 PC/Printer applications connections: Terminal 1 (Transmit), 2 (Receive), 3 (Ground) EIA-485 (ACS) - TB9 ACS annunciator connector, Terminal 1 (+) and Terminal 2 (-), requires ferrite bead 1.2.1 Current Availability The following figure illustrates the maximum current that is possible for each panel circuit and the...

  • Page 15: Controls And Indicators

    Controls and Indicators Product Description 1.3 Controls and Indicators LCD Display The FACP uses an 80-character HONEYWELL LIFE SAFETY (4 lines X 20 characters) high viewing angle SYSTEM ALL NORMAL 10:00A 012106 LCD display. The display includes a long life LED backlight that remains illuminated.

  • Page 16: Circuits

    Product Description Circuits 1.4 Circuits SLC Communication Loop One SLC loop is provided standard on the FACP main circuit board. The SLC loop, configurable for NFPA Style 4, 6 or 7, provides communication to addressable detectors, monitor (initiating device) and control (output device) modules. Refer to the FireWarden SLC Wiring manual for information on wiring devices.

  • Page 17: Components

    Components Product Description ✓ 12 Tone Burst types: 20 pps (3+1, 4+1, 4+2, 3+1 Exp., 4+1 Exp., 4+2 Exp.) ✓ 3 Touchtone Types 4+1 Ademco Express 4+2 Ademco Express Ademco Contact ID 1.6 Components Main Circuit Board The main circuit board contains the system’s CPU, power supply, other primary components and wiring interface connectors.

  • Page 18: 3: Addressable Device Accessories

    Product Description Optional Modules These devices can operate in CLIP mode (Classic Loop Interface Protocol) or LiteSpeed mode to provide a quicker response. Refer to the FireWarden SLC Wiring Manual for a list of compatible addressable modules. Refer to the Device Compatibility Document for a list of approved conventional notification and initiating devices.

  • Page 19: 3: Battery Box

    Accessories Product Description 1.8.3 Battery Box NFS-LBB The NFS-LBB battery box may be used to house two 25 AH batteries, two 60 AH batteries or one 100 AH battery. When the CHG-120 is mounted in the NFS-LBB, two 25 AH or one 60 AH battery may also be housed in the battery box.

  • Page 20: Getting Started

    Product Description Getting Started • AFM-16AT Annunciator Fixed Module annunciates 16 zones with 16 red alarm LEDs and 16 yellow trouble LEDs. In addition, it has a System Trouble LED, an On Line/Power LED and a local piezo sounder. It also has switches for FACP Acknowledge, Silence, Reset and Drill.

  • Page 21: 2: Digital Communicator

    Telephone Requirements and Warnings Product Description Complies with FCC Part 68 Mates with RJ31X Male Connector Supervision Threshold: less than 4.0 volts for 2 minutes The REN is used to determine the quantity of devices which may be connected to the telephone line.
  • Page 22 Product Description Telephone Requirements and Warnings When the control panel activates, premise phones will be disconnected. Two separate phone lines are required. Do not connect both telephone interfaces to the same telephone line. The control panel must be connected to the public switched telephone network upstream (as first device) of any private telephone system at the protected premises.

  • Page 23: Section 2: Installation

    Section 2: Installation The cabinet may be either semi-flush or surface mounted. The cabinet mounts using two key slots and two 0.250” (6.35 mm) diameter holes located in the backbox. The key slots are located at the top of the backbox and the two securing holes at the bottom. Carefully unpack the system and check for shipping damage.

  • Page 24: Mounting The Assembly

    Installation Mounting the Assembly 2.2 Mounting the Assembly One XRM-24(E) transformer is supplied standard with the control panel. An optional second XRM-24(E) transformer can be ordered and installed to provide maximum system power. Install the transformers in the locations indicated in the following illustration. When the location is dry and free of construction dust, install the chassis/transformer/circuit board assembly.
  • Page 25 Mounting the Assembly Installation Semi-Flush Mounting Do not recess box more than 3.875” into wall to avoid covering venting holes on top of box. Figure 2.3 NFW2-100 Cabinet Mounting FireWarden 100-2/E — P/N 52778:A 11/04/2005...
  • Page 26 Installation Mounting the Assembly Figure 2.4 NFW2-100 Cabinet Dimensions FireWarden 100-2/E — P/N 52778:A 11/04/2005...

  • Page 27: Power

    Power Installation 2.3 Power WARNING: Several different sources of power can be connected to this panel. Disconnect all sources of power before servicing. The panel and associated equipment may be damaged by removing and/or inserting cards, modules or interconnecting cables while this unit is energized. 2.3.1 AC Power and Earth Ground Connection Primary power required for the FACP is 120 VAC, 60 Hz, 3.0 LCD DISPLAY...

  • Page 28: 3: Special Application Dc Power Output Connection

    Installation Relays 2.3.3 Special Application DC Power Output Connection All Special Application DC power outputs are power-limited and require a ferrite bead per FCC requirements (refer to“UL Power-limited Wiring Requirements” on page 32). Power-limited Resettable Power Power-limited Resettable or Nonresettable Power 0.5 amperes max., 24 VDC nominal filtered, resettable power can be 0.5 amperes max., 24 VDC nominal filtered, resettable drawn from TB1 Terminals 3(+) and 4(-)

  • Page 29: 1: Configuring Nacs

    Notification Appliance Circuits Installation The following sections describe the configuration and wiring of Style Y and Style Z Notification Appliance Circuits on the NFW2-100 main circuit board. The NACs are configured for Style Y (Class B) from the factory. Refer to “Configuring NACs” on page 29 for information on changing the NAC configuration to Style Z (Class A).

  • Page 30: 2: Style Y (Class B) Nac Wiring

    Installation Notification Appliance Circuits 2.5.2 Style Y (Class B) NAC Wiring 4 Style Y (Class B) Notification Appliance Circuits, supervised and power-limited - 4.7 k ohm, ½ watt P/N:71252 UL listed NAC 4 NAC 1 NAC 2 NAC 3 Polarized Bells Polarized Bells Polarized Strobes Polarized Strobes...

  • Page 31: Remote Synchronization Output

    Remote Synchronization Output Installation 2.6 Remote Synchronization Output Synchronization is a feature that controls the activation of notification appliances in such a way that all devices will turn on and off at exactly the same time. This is particularly critical when activating strobes which must be synchronized to avoid random activation and a potential hazard to individuals.

  • Page 32: Ul Power-Limited Wiring Requirements

    Installation UL Power-limited Wiring Requirements 2.7 UL Power-limited Wiring Requirements Power-limited and nonpower-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” (6.35 mm) away from any nonpower- limited circuit wiring and nonpower-limited circuit wiring must enter and exit the cabinet through different knockouts and/or conduits.

  • Page 33: Digital Communicator

    Digital Communicator Installation 2.8 Digital Communicator Two independent telephone lines can be connected to the control panel. Telephone line control/command is made possible via double line seizure as well as usage of an RJ31X style interconnection. Note that it is critical that the panel's digital communicator be located as the first device on the incoming telephone circuit to properly function.

  • Page 34: Optional Module Installation

    Installation Optional Module Installation 2.9 Optional Module Installation WARNING: Disconnect all sources of power (AC and DC) before installing or removing any modules or wiring. NFW2-100 Keypad/Display Removal Removal of the keypad/display is normally not necessary. If, however, it becomes necessary to replace the keypad/display or access jumpers JP5 and JP7 or switch SW1, the Keypad/Display can be removed by inserting a Phillips screwdriver into each of the three holes located in the flexible covering of the Keypad/Display and loosening the three mounting screws.
  • Page 35 Optional Module Installation Installation Remote Station Service (NFPA 72 Remote Station Fire Alarm Systems) - Intended for connection to a polarity reversal circuit or a Remote Station receiving unit having compatible ratings: Maximum load for each circuit: 10 mA Reverse polarity output voltage: 24 VDC Remote Alarm and Remote Trouble wiring can leave the building Before installing the module, place the disconnect switch to the right (disconnect) position to prevent accidental activation of the municipal box.

  • Page 36: 2: Printer/Pc

    Installation Optional Module Installation When the installation has been complete, enable the 4XTM module by sliding the disconnect switch to the left Test system for proper operation SHIELD TB10 B+ A+ B- A- NO NC C NO NC C OUT+ IN+ OUT- IN- Standoff Standoff RELAY 1...

  • Page 37: 3: Digital Communicator And Annunciators

    Optional Module Installation Installation Note that the printer may or may not be supervised as determined by user programming. Refer to“Printer/PC” on page 112. 5 4 3 2 1 White 9 8 7 6 Green Black PRT/PK-CABLE GRND TB10 SHIELD B+ A+ B- A- OUT+ IN+ OUT- IN- Figure 2.17 Serial Printer and Computer Connections...
  • Page 38 Installation Optional Module Installation Annunciator addressing is specific to the NFW2-100 control panel. The following table describes the annunciator addresses and the corresponding addressable devices that will be annunciated at each annunciator address. ACM Annunciator Address Annunciator Displays the Following Points 8 General System Status Points &...

  • Page 39: Section 3: Programming

    Section 3: Programming NOTICE TO USERS, INSTALLERS, AUTHORITIES HAVING JURISDICTION AND OTHER INVOLVED PARTIES This product incorporates field-programmable software. In order for the product to comply with the requirements in the Standard for Control Units and Accessories for Fire Alarm Systems, UL 864, certain programming features or options must be limited to specific values or not used at all as indicated below: Program feature Permitted in...

  • Page 40: User Programming

    The System All Normal screen will be displayed in a programmed system with no active alarms, troubles or supervisories, as illustrated below: HONEYWELL LIFE SAFETY SYSTEM ALL NORMAL 10:00A 012102 Programming, Read Status and Manual Dial mode can be entered while the panel is in any mode of operation.

  • Page 41: Initial Power-Up

    Initial Power-up Programming User Programming Levels There are two user programming levels: • User Master Program Level 1 is used for programming panel specific data relating to device types, zoning, messages, control panel functions, etc. • User Maintenance Program Level 2 is used by a qualified operator to access features such as Disable/Enable, View and Clear History, Walktest and System Time Change.
  • Page 42 Programming Programming and Passwords To access user Programming mode, press the Enter or Mode key. The LCD will display the following: 1=READ STATUS MODE 2=PROGRAMMING MODE 3=MANUAL DIAL MODE To enter the user Programming mode, press 2. The display will read as follows: PROGRAMMING ENTER PASSWORD *****...

  • Page 43: Master Programming Level

    Master Programming Level Programming 3.6 Master Programming Level When the Master Program Level password is entered, the control panel will enter user Programming mode. In this mode, the piezo sounder remains off, the trouble relay is activated and the system Trouble LED flashes until Programming mode is exited. The following display will appear: PROGRAMMING 1=AUTOPROGRAM...

  • Page 44: 1=Autoprogram

    Programming Master Programming Level 3.6.1 Autoprogram Pressing 1 while viewing Programming Screen #1, will select the Autoprogram option, which PROGRAMMING prompts the control panel to poll all devices installed on the SLC loop. The primary purpose of 1=AUTOPROGRAM autoprogramming is to allow the installer a fast and easy way to bring the system on-line as quickly 2=POINT PROGRAM as possible.
  • Page 45 Master Programming Level Programming Detector Programming Pressing 1, while viewing the Point Program Screen, will allow the programmer to add, delete or change the programming of an addressable detector. The following screen will be displayed by the control panel: DETECTOR 1=ADD 2=DELETE 3=EDIT...
  • Page 46 Programming Master Programming Level Delete Detector Pressing 2 in the Detector Screen will display the Delete Detector Screen which allows the DETECTOR programmer to delete a specific detector: 1=ADD 2=DELETE 3=EDIT DELETE DETECTOR Detector Screen ENTER DETECTOR# Delete Detector Screen A flashing cursor will appear in the position of the first asterisk to the left.
  • Page 47 Master Programming Level Programming If the selected address has been added to programming, device summary screens will be displayed. These screens allow the programmer to view all device settings at a single glance. Pressing the left or right arrow keys will allow the programmer to rapidly view the devices at the previous or next address (if installed).
  • Page 48 Programming Master Programming Level The following examples show the editing of a photoelectric smoke detector with address 017, located on the SLC loop: EDIT DETECTOR 1D017 1=ENABLED 2=TYPE SMOKE(PHOTO) 3=VERIFICATION Edit Detector Screen #2 EDIT DETECTOR 1D017 1=WALKTEST 2=PAS 3=PRE-SIGNAL Edit Detector Screen #3 EDIT DETECTOR 1D017 1=ZONE ASSIGNMENT...
  • Page 49 Master Programming Level Programming Type To select the type of detector being programmed, press the 2 key while viewing the Edit Detector EDIT DETECTOR Screen #2. This will cause the control panel to display the following Detector Type Screens: 1=ENABLED 2=TYPE 3=VERIFICATION DETECTOR TYPE...
  • Page 50 Programming Master Programming Level signaling device to indicate PAS activation (do not use a Notification Appliance Circuit for this purpose). To enable the PAS feature, press 2 while viewing the Edit Detector Screen #3 until the display reads PAS Yes. Each press of the 2 key will cause the display to toggle between PAS Yes and PAS No.
  • Page 51 Master Programming Level Programming Zone Assignment A maximum of five zones can be programmed to each addressable detector. Pressing 1 while EDIT DETECTOR viewing Edit Detector Screen #4 displays the following screen: 1=ZONE ASSIGNMENT 00 ** ** ** ** ZONE ASSIGNMENT Edit Detector Screen #4 Z00 Z** Z** Z** Z** Zone Assignment Screen...
  • Page 52 Programming Master Programming Level Pressing 1 while viewing the Noun/Adjective Screen will cause the following screen(s) to be 1=STANDARD ADJECTIVE displayed. Note that the keyboard down arrow key must be pressed to see all the Adjective screens. 2=STANDARD NOUN Press the number corresponding to the adjective that is to be used as a descriptor for the location of 3=CUSTOM ADJECTIVE the detector currently being programmed.
  • Page 53 Master Programming Level Programming Pressing 2 while viewing the Noun/Adjective Screen will cause the following screen(s) to be 1=STANDARD ADJECTIVE displayed. Note that the keyboard down arrow key must be pressed to see all the Noun screens. 2=STANDARD NOUN Press the number corresponding to the noun that is to be used as a descriptor for the location of the 3=CUSTOM ADJECTIVE detector currently being programmed.
  • Page 54 Programming Master Programming Level Pressing 3 or 4 while viewing the Noun/Adjective Screen will display screens similar to the 1=STANDARD ADJECTIVE previous Adjective and Noun Screens. The new screens will list custom Adjectives and Nouns 2=STANDARD NOUN which have been programmed into the control panel using the VeriFire Warden programming kit. 3=CUSTOM ADJECTIVE These descriptors are selected as described in the previous sections.
  • Page 55 Master Programming Level Programming With the cursor on the first letter of the Noun field, press the zero key twice to recall the display ROOM_304. The cursor automatically jumps from the first to the last letter of the Noun field With the cursor on the last letter of the Noun field, press the zero key again to increment the room number to 305 Press the right arrow key to advance the zone field...
  • Page 56 Programming Master Programming Level Pressing 1 for Control Module or 2 for Monitor Module will cause the following screen to be displayed: ADD MODULE MODULE# IS ADDED Add Module Screen #3 The programmer can continue adding modules by pressing the ESC or left arrow key which will return the display to the Add Module Screen #1.
  • Page 57 Master Programming Level Programming A flashing cursor will appear in the position of the first asterisk to the left. The programmer keys in the three digit module address, such as 012. When the last digit is keyed-in, if the selected address has not been added to programming, a screen showing information about the highest address that is installed will be displayed.
  • Page 58 Programming Master Programming Level If the selected address corresponds to a monitor module, a screen displaying information about the module with the selected address will be displayed as illustrated in the following: NORMAL MONITOR <ADJ><NOUN> ZNNN 1M012 EDIT MONITOR 1M012 1=ENABLED 2=TYPE MONITOR...
  • Page 59 Master Programming Level Programming Type Monitor Using the VeriFire Warden Upload/Download utility program, unique user-defined monitor types EDIT MONITOR can be created and loaded into the FACP for later use. The FACP response to the activation of a 1=ENABLED 2=TYPE MONITOR user-defined type is the same as most previous standard types in the list, thus allowing a variety of user-defined types and responses.
  • Page 60 Programming Master Programming Level Monitor module type selection will affect the function of the point as follows: Table 3.1 Monitor Types Monitor Type Action When Activated Pull-Station Fire Alarm User-Defined-1 same as previous (Pull-Station) Waterflow Fire Alarm Delayed User-Defined-2 same as previous (Waterflow) Monitor Fire Alarm User-Defined-3...
  • Page 61 Master Programming Level Programming Pre-signal EDIT MONITOR 1=PRE-SIGNAL To enable the Pre-signal feature, press 1 while viewing Edit Monitor Screen #3 until the display reads Pre-signal Yes. Each press of the 1 key will cause the display to toggle between Pre-signal Yes and Pre-signal No.
  • Page 62 Programming Master Programming Level Pressing 1 while viewing the Noun/Adjective Screen will cause the following screen(s) to be 1=STANDARD ADJECTIVE displayed. Note that the keyboard down arrow key must be pressed to see all the Adjective screens. 2=STANDARD NOUN Press the number corresponding to the adjective that is to be used as a descriptor for the location of 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN the monitor module currently being programmed.
  • Page 63 Master Programming Level Programming Pressing 2 while viewing the Noun/Adjective Screen will cause the following screen(s) to be 1=STANDARD ADJECTIVE displayed. Note that the keyboard down arrow key must be pressed to see all the Noun screens. 2=STANDARD NOUN Press the number corresponding to the noun that is to be used as a descriptor for the location of the 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN monitor module currently being programmed.
  • Page 64 Programming Master Programming Level The Description selection allows the programmer to enter additional information about the monitor EDIT MONITOR module currently being programmed. This information will be displayed as part of the device label 1=NOUN/ADJECTIVE on the LCD display. Pressing 2 while viewing Edit Monitor Screen #5 will cause the following 2=DESCRIPTION ***************** screen to be displayed:...
  • Page 65 Master Programming Level Programming Edit Module Screen for Control Modules The programmer can change a module’s existing or factory default programming by pressing 3 in the Modules Screen. The following screen will be displayed: MODULES 1=ADD 2=DELETE EDIT MODULE 3=EDIT ENTER MODULE ADDRESS Modules Screen Edit Module Screen...
  • Page 66 Programming Master Programming Level To change the programming for the displayed module, press the keyboard down arrow key to view the following Edit Control screens: EDIT CONTROL 1=ENABLED 2=TYPE CONTROL 3=SILENCEABLE Edit Control Screen #2 EDIT CONTROL 1=WALKTEST 2=ZONE ASSIGNMENT 00 ** ** ** ** Edit Control Screen #3 EDIT CONTROL...
  • Page 67 Master Programming Level Programming While viewing one of the Control Type screens, select the type of control module being programmed by pressing the corresponding keypad number key. The display will return to the Edit Control Screen #2 and indicate the new type selection. NOTE: A control module set to the Resettable Power type will follow the main circuit board 24 VDC resettable power unless the control module is disabled.
  • Page 68 Programming Master Programming Level Note that Z** represents the Zone Number(s) corresponding to this device. The factory default for an unprogrammed device is Z00 for general alarm zone. A flashing cursor will appear on the first 0 to the left. Enter the two digit number corresponding to the zone that is to be assigned to this device.
  • Page 69 Master Programming Level Programming Pressing 1 while viewing the Noun/Adjective Screen will cause the following screen(s) to be 1=STANDARD ADJECTIVE displayed. Note that the keyboard down arrow key must be pressed to see all the Adjective screens. 2=STANDARD NOUN Press the number corresponding to the adjective that is to be used as a descriptor for the location of 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN the control module currently being programmed.
  • Page 70 Programming Master Programming Level Pressing 2 while viewing the Noun/Adjective Screen will cause the following screen(s) to be 1=STANDARD ADJECTIVE displayed. Note that the keyboard down arrow key must be pressed to see all the Noun screens. 2=STANDARD NOUN Press the number corresponding to the noun that is to be used as a descriptor for the location of the 3=CUSTOM ADJECTIVE 4=CUSTOM NOUN control module currently being programmed.
  • Page 71 Master Programming Level Programming Description EDIT CONTROL 1=ADJECTIVE/NOUN The Description selection allows the programmer to enter additional information about the control 2=DESCRIPTION module currently being programmed. This information will be displayed as part of the device label on the display. Pressing 2 while viewing Edit Control Screen #4 will cause the following screen to Edit Control Screen #4 be displayed: DESCRIPTION...

  • Page 72: 3: Zone Setup

    Programming Master Programming Level 3.6.3 Zone Setup Pressing 3 while viewing Programming Screen #2 will access the Zone Setup screens as illustrated PROGRAMMING below: 1=AUTOPROGRAM 2=POINT PROGRAM 3=ZONE SETUP ZONE SETUP Programming Screen #2 1=ENABLE 2=DISABLE 3=ZONE 97 98 99 Zone Setup Screen #1 ZONE SETUP 1=ZONES INSTALLED...
  • Page 73 Master Programming Level Programming Disable Pressing 2 for Disable, while viewing Zone Setup Screen #1, displays the following: ZONE SETUP 1=ENABLE 2=DISABLE ZONE TO DISABLE 3=ZONE 97 98 99 Zone Setup Screen #1 Disable Screen This screen allows the programmer to disable zones, one at a time. A flashing cursor appears next to the Z, prompting the programmer to enter a two digit zone number (01 - 99).
  • Page 74 Programming Master Programming Level Zones Installed Pressing 1 for Zones Installed, while viewing Zone Setup Screen #2, will display a screen similar to ZONE SETUP 1=ZONES INSTALLED the following: 2=ZONES ENABLED 3=ZONES DISABLED Zone Setup Screen #2 ZONES INSTALLED 00 01 02 03 04 05 Zones Installed Screen This display will show all of the zones that have been programmed into the control panel.
  • Page 75 Master Programming Level Programming Zone Type Zone Types must be programmed only if a DACT, programmed for zone reporting, is installed on ZONE SETUP the control panel. Pressing 1 for Zone Types, while viewing Zone Setup Screen #3, will display a 1=ZONE TYPES screen similar to the following: 2=ZONES AVAILABLE...

  • Page 76: 4: Loop Setup

    Programming Master Programming Level Zones Available Pressing 2 while viewing Zone Setup Screen #3 will display a screen similar to the following: ZONE SETUP 1=ZONE TYPES 2=ZONES AVAILABLE ZONES AVAILABLE 3=ZONE MESSAGE 01 02 03 04 05 06 07 Zone Setup Screen #3 08 09 10 11 12 13 14 15 16 17 18 19 20 21 The display will show all of the zones that are still available for programming.

  • Page 77: 5: System Setup

    • Banner: This option allows the user to change the top two lines of the LCD display from the factory default readout of HONEYWELL LIFE SAFETY to a user defined readout when the control panel is in Normal condition.
  • Page 78 2=USER DEFINED display the following screen: Banner Screen FACTORY BANNER HONEYWELL LIFE SAFETY Factory Banner Screen Pressing the Enter key will store this selection in nonvolatile memory and return the display to the Banner Screen. Pressing 2 while viewing the Banner Screen will cause the following screens to be displayed:...
  • Page 79 Master Programming Level Programming characters in the first screen, press Enter to view the second screen. Enter up to 20 characters in the second screen in the same manner or just press Enter if a second banner line is not being entered. To quickly clear the current banner, press the CLR key.
  • Page 80 Programming Master Programming Level Date To change the date, press 2 while viewing the Time-Date Screen. The following screen will be displayed: ENTER DATE MONTH DAY YEAR 04-07-2002 Date Screen A flashing cursor is located toward the top left of the display. Below the cursor is the current date. To change the date, enter the two-digit month followed by the two-digit day and then the two-digit year (01 for 2001, 02 for 2002, etc.).
  • Page 81 Master Programming Level Programming Pressing 3 while viewing Daylight Savings Screen #1 will display two sub-screens which allow the programmer to select the week of the month that daylight savings time will begin. In the first sub- screen, pressing 1 will select the first week, 2 will select the second week and 3 will select the third week, while in the second sub-screen, pressing 1 will select the fourth week and 2 will select the last week of the selected month.
  • Page 82 Programming Master Programming Level Pre-signal Delay The factory default setting for Pre-signal delay is 000 for no delay. To select a Pre-signal delay of 001 to 180 seconds for all devices programmed for Pre-signal, press 2 while viewing Timer Screen #1.
  • Page 83 Master Programming Level Programming AC Loss Delay TIMER 1=AC LOSS DELAY The reporting of a loss of AC power to a central station can be delayed by programming the length of the desired delay. Press 1 while viewing Timer Screen #2 to display the following: Timer Screen #2 AC LOSS DELAY 1=NO DELAY...
  • Page 84 Programming Master Programming Level The following screens will be displayed for each selection: NAC # 1=ENABLED 2=TYPE BELL 3=SILENCEABLE NAC Screen #1 NAC # 1=AUTO SILENCE 2=CODING TEMPORAL NAC Screen #2 NAC # 1=ZONE 00 00 00 00 00 2=SIL INHIBITED NAC Screen #3 NAC # 1=SYNC TYPE...
  • Page 85 Master Programming Level Programming Type The main circuit board NAC type can be programmed by pressing 2 while viewing NAC Screen #1. NAC # The following screen will be displayed. Press the down arrow key to view additional screens: 1=ENABLED 2=TYPE 3=SILENCEABLE NAC Screen #1...
  • Page 86 Programming Master Programming Level Auto Silence The Auto Silence feature, when enabled, automatically silences all main circuit board silenceable NAC # notification appliances after a programmed length of time. To enable this feature and program the 1=AUTO SILENCE time delay before Auto Silence activation, press 1 while viewing NAC Screen #2. The following 2=CODING TEMPORAL screens will be displayed:...
  • Page 87 Master Programming Level Programming Coding (only for NACs not programmed as Sync Strobe Type) The Coding feature allows the programmer to select the type of output that the main circuit board notification appliances will generate when activated. Pressing 2 while viewing NAC Screen #2 will cause the following displays to appear: CODING 1=STEADY...
  • Page 88 Programming Master Programming Level If another alarm point is activated and the countdown timer has stopped counting due to the Acknowledge switch being pressed, the countdown timer will restart and the NACs will respond as outlined in step 2. NACs already in 2nd stage activation will not be affected Any control modules assigned to special Zone 99 will be activated either by direct mapping of an input device programmed to Zone 99 or if the timer counts down to zero Control modules that are programmed to the same zone as the activated input device will not...
  • Page 89 Master Programming Level Programming To ensure proper strobe and circuit operation, there is also a limit to the number of strobes that can be attached to each circuit. Following is a list of the strobes that have been tested with this FACP and the maximum number that can be connected to each NAC.

  • Page 90: 6: Verify Loop

    Programming Master Programming Level While viewing the selected screen, press the number corresponding to the desired relay type to program the main circuit board relay. The choice will be stored in memory and the display will return to the Relay Type Screen which will show the programmed type choice. Press the Escape key to return to the Relays Selection Screen and repeat the preceding procedure for the remaining relays.

  • Page 91: 7: History

    Master Programming Level Programming 3.6.7 History The History option allows an authorized user to view or erase events which have occurred in the PROGRAMMING control panel. Pressing 1 while viewing Programming Screen #3 will display the History options 1=HISTORY as shown in the following display: 2=WALKTEST 3=OPTION MODULES Programming Screen #3...

  • Page 92: 8: Walktest

    Programming Master Programming Level 3.6.8 Walktest Walktest allows an individual to test the fire alarm system without the necessity to reset the control PROGRAMMING panel after each device activation. Pressing 2 while viewing the Programming Screen #3 will cause 1=HISTORY the following Walktest options to be displayed: 2=WALKTEST 3=OPTION MODULES...

  • Page 93: 9: Option Modules

    Master Programming Level Programming 3.6.9 Option Modules Options available for the NFW2-100 include ACS Series, Graphic and LCD annunciators, printer PROGRAMMING connection for acquiring hardcopy printouts of panel data and PC (Personal Computer) connection 1=HISTORY for uploading and downloading panel data. 2=WALKTEST 3=OPTION MODULES Pressing 3 while viewing Programming Screen #3 will display the following screen:...
  • Page 94 Programming Master Programming Level If an ACS annunciator is installed, press 1 while viewing Annunciator Screen #2 to select addresses for the ACS annunciators. The following screen will be displayed: ANNUNCIATOR 1=ADDRESS 1 2=ADDRESS 2 3=ADDRESS 3 ACS Installed Screen Pressing the down arrow key will allow the programmer to view additional screens displaying Addresses 1 -31.
  • Page 95 Master Programming Level Programming Primary Phone Press 2 while viewing On Board DACT Screen #1 to program the type of primary phone line being connected to the DACT. The following screen will be displayed: ON BOARD DACT PRIMARY PHONE LINE 1=TYPE TOUCHTONE Primary Phone Line Screen...
  • Page 96 Programming Master Programming Level Service Terminal The NFW2-100 can be programmed remotely from a PC using a modem and telephone line. ON BOARD DACT Information can also be retrieved from the FACP using the same method. The Upload/Download 1=SERVICE TERMINAL option allows an operator to set the necessary parameters to allow the uploading and downloading 2=CENTRAL STATION of data between the FACP and PC.
  • Page 97 Master Programming Level Programming Terminal 1 and Terminal 2 Service Terminal #1 is generally designated as the FACP primary phone line used for receiving SERVICE TERMINAL phone calls from the service terminal (PC) being used for remote programming. Service Terminal 1=PANEL ID 2 is referred to as the secondary phone line.
  • Page 98 Programming Master Programming Level Ring Count SERVICE TERMINAL The ring count designates the number of rings allowed on the phone line prior to answering an 1=RING COUNT incoming call from a service terminal. The factory default is 3 which means the control panel will not answer an incoming call until 3 rings are detected.
  • Page 99 Master Programming Level Programming Backup Reporting The DACT can be programmed to transmit reports to primary and/or secondary central station phone numbers as a backup. Press 2 while viewing Central Station Screen #1 to display the following screen: BACKUP REPORTING 1=BACKUP ONLY 2=BOTH 3=FIRST AVAILABLE...
  • Page 100 Programming Master Programming Level Central Station Primary and Secondary Phone Numbers Pressing 1 for Primary or 2 for Secondary will display the following screens. CENTRAL STATION 1=PRIMARY Note that the following information must be entered for both the Primary and Secondary Central 2=SECONDARY Station Phone Numbers.
  • Page 101 Master Programming Level Programming Test Time Interval CENTRAL STATION Pressing 1 while viewing Primary/Secondary Screen #1 will cause the following screens to be 1=TEST TIME INT 2=ACCOUNT CODE displayed: 3=24HR TST TIME Primary/Secondary Screen #1 TEST TIME INTERVAL 1=24 HOURS 2=12 HOURS 3=8 HOURS Test Time Interval Screen #1...
  • Page 102 Programming Master Programming Level 24 Hour Test Time CENTRAL STATION Pressing 3 while viewing Primary/Secondary Screen #1 will cause the following screen to be 1=TEST TIME INT 2=ACCOUNT CODE displayed: 3=24HR TST TIME Primary/Secondary Screen #1 24 HOUR TEST TIME RANGE 0000-2359 24 Hour Test Time Screen Use the 24 Hour Test Time screen to program the time that the DACT will transmit the 24 Hour...
  • Page 103 Master Programming Level Programming Communication Format CENTRAL STATION Pressing 1 while viewing Primary/Secondary Screen #3 will cause the following screens to be 1=COMM FORMAT displayed: Primary/Secondary Screen #3 COMM FORMAT 1=ADEMCO EXPRESS 4P1 2=ADEMCO EXPRESS 4P2 3=3P1S C18 A23 Comm Format Screen #1 COMM FORMAT 1=3P1E C18 A23 2=3P1S C19 A14...
  • Page 104 Programming Master Programming Level The Communication Format is determined by the type of receiver that the DACT is transmitting to. Consult your Central Station for proper selection or consult our factory representatives. For any format chosen, the control panel automatically programs all of the event codes. Select the Communication Format by pressing the corresponding number key while viewing the appropriate Comm Format screen.
  • Page 105 Master Programming Level Programming 3+1, 4+1 Express and 4+1 Standard The information shown in Table 3.2 is automatically programmed for the Central Station phone number Event Codes when any of these Formats are selected. Enter 0 for an Event Code Setting to disable the report.
  • Page 106 Programming Master Programming Level Table 3.2 Event Codes (Continued) PROCMON AR MON-USER-DEF-17 not used not used POINT_FAULT POINT_DISABLE AC_FAIL DRILL SLC 1 OPEN FAULT SLC 1 SHORT FAULT not used not used GROUND FAULT LOW BATTERY NO_BATTERY TELCO LINE 1 TELCO LINE 2 COMM FAULT 1 COMM FAULT 2...
  • Page 107 Master Programming Level Programming 4+2 Standard, 4+2 Express, 3 + 1, 4 + 1 and 4+2 Expanded Formats The information shown in Table 3.3 is automatically programmed for the Central Station phone number Event Codes when any of these Formats are selected. Enter 00 for an Event Code Setting to disable the report.
  • Page 108 Programming Master Programming Level Table 3.3 Event Codes (Continued) PROCMON AR MON-USER-DEF-17 not used not used POINT_FAULT POINT_DISABLE AC_FAIL DRILL SLC 1 OPEN FAULT SLC 1 SHORT FAULT not used not used GROUND FAULT LOW BATTERY NO_BATTERY TELCO LINE 1 TELCO LINE 2 COMM FAULT 1 COMM FAULT 2...
  • Page 109 Master Programming Level Programming Ademco Contact ID Format The information shown in Table 3.4 is automatically programmed for the Central Station phone number Event Codes when Ademco Contact ID Format is selected. Enter 000 for an Event Code Setting to disable the report. Table 3.4 Event Codes Event Description Event Code Settings...
  • Page 110 Programming Master Programming Level Table 3.4 Event Codes (Continued) PROCMON AR MON-USER-DEF-17 not used not used POINT_FAULT POINT_DISABLE AC_FAIL DRILL SLC 1 OPEN FAULT SLC 1 SHORT FAULT not used not used GROUND FAULT LOW BATTERY NO_BATTERY TELCO LINE 1 TELCO LINE 2 COMM FAULT 1 COMM FAULT 2...
  • Page 111 Master Programming Level Programming Report Style Pressing 3 while viewing Central Station Screen #2 will cause the Report Style display to toggle CENTRAL STATION between Point and Zone. Setting the Report Style to Point will program the DACT to report 1=PRIMARY individual point status to the Central Station.
  • Page 112 Programming Master Programming Level Printer/PC A Printer or a PC can be connected to the control panel. Pressing 3 while viewing the Option OPTION MODULES Module Screen will cause the following screen to appear: 1=ANNUNCIATORS/UDACT 2=ON BOARD DACT 3=PRINTER/PC PRINTER-PC Option Module Screen 1=PRINTER NO SU 2=PRINTER SU...

  • Page 113: 10: Password Change

    Master Programming Level Programming 3.6.10 Password Change The factory set passwords, which have been programmed into the control panel, can be changed by PROGRAMMING selecting the Password Change option. Pressing 1 while viewing Programming Screen #4 will 1=PASSWORD CHANGE cause the following screen to be displayed: 2=CLEAR PROGRAM 3=PROGRAM CHECK Programming Screen #4...

  • Page 114: 12: Program Check

    Programming Master Programming Level Pressing 1, for Whole System while viewing the Clear Program Screen #1, will clear all general system programming options and all programmed addressable devices from the nonvolatile memory of the FACP. This function is useful when the control panel is first installed, prior to autoprogramming. Note that it is necessary to autoprogram after using the Clear Whole System function.
  • Page 115 Master Programming Level Programming view all the NAC zones without input assignments for NAC 1, NAC2, NAC 3 and NAC 4. NOTE: If the NACs have been configured for Class A in the Setup option, only NAC1 and NAC 2 will display test information.

  • Page 116: Maintenance Programming Level

    Programming Maintenance Programming Level 3.7 Maintenance Programming Level To access Maintenance Programming mode, press the Enter key. The LCD will display the following: 1=READ STATUS 2=PROGRAMMING To enter the Maintenance Programming mode, press 2. The display will read as follows: PROGRAMMING ENTER PASSWORD When the Maintenance level password (default 11111) is entered, the following screen will appear:...

  • Page 117: 1: Disable Point

    Maintenance Programming Level Programming 3.7.1 Disable Point Pressing 1 for Point Program, while viewing Maintenance Screen #1 will cause the following PROGRAMMING screens to be displayed: 1=POINT PROGRAM 2=HISTORY 3=PROGRAM CHECK POINT PROGRAM Maintenance Screen #1 1=DETECTOR 2=MODULE Device Select Screen Select the device type by pressing 1 for an addressable detector or 2 for an addressable module.

  • Page 118: 3: Program Check

    Programming Maintenance Programming Level The History feature allows the operator to view control panel events which have been stored in a history file in memory and erase the contents of the history file Pressing 1 while viewing the History screen will cause the following screen to be displayed: HISTORY 1=VIEW ALL 2=VIEW ALARMS...
  • Page 119 Maintenance Programming Level Programming The Program Check feature allows the programmer to view the zones which have been programmed to the Notification Appliance Circuits on the control panel but have not been programmed to Initiating Devices as well as other circuits with no input or output correlations. Pressing 1 while viewing Program Check screen will cause a screen similar to the following to be displayed.

  • Page 120: 4: Walktest

    Programming Maintenance Programming Level The Zone No Output feature allows the programmer to view the zones which have not been programmed to at least one output device (not including general alarm Zone 00). The example in the preceding screen indicates that Zones 05, 07, 09, 10 and 11 have been programmed to an addressable detector with an address of 001 on the loop but have not been programmed to any output devices.

  • Page 121: 6: Zone Setup

    Maintenance Programming Level Programming To change the time, press 1 to display the following screen: ENTER TIME 01:00 AM 1=AM 2=PM Time Screen A flashing cursor will appear on the left side of the display. Enter the four digit number corresponding to the time (0000 - 1259).
  • Page 122 Programming Maintenance Programming Level Pressing 1 while viewing Zone Setup screen will display the following screen: ZONE TO ENABLE Enable Screen A flashing cursor appears to the right of the Z. To enable a zone, enter the two digit zone number (00 - 99).
  • Page 123 Maintenance Programming Level Programming device connected to the control module can be used to indicate a PAS condition in the control panel. Do not assign Zone 97 to a Notification Appliance Circuit when using this zone to indicate a PAS condition. Pressing 2 will cause the display to change to Pre-signal 98 On.

  • Page 124: Section 4: Operating Instructions

    Section 4: Operating Instructions 4.1 Panel Control Buttons 4.1.1 Acknowledge/Step The first press of the Acknowledge/Step key silences the piezo sounder, changes flashing LEDs to steady and also changes the status field on the LCD display from capital letters to small letters. When the piezo is silenced, an acknowledge message is sent to the printer and the history file.
  • Page 125 LED Indicators Operating Instructions Supervisory This is a yellow LED that flashes when one or more supervisory conditions occur, such as a sprinkler valve tamper condition. It illuminates steady when the Acknowledge/Step or Alarm Silence key is pressed. It turns off when the Reset key is pressed and remains off if all supervisory alarms have been cleared.

  • Page 126: Normal Operation

    With no alarms or troubles in the system, the display message is System All Normal along with the current time and date as shown below. To set the time and date, refer to the appropriate section in this manual. HONEYWELL LIFE SAFETY SYSTEM ALL NORMAL 10:00A 012106 The NFW2-100 performs the following functions at regular intervals while in Normal mode: •...
  • Page 127 Trouble Operation Operating Instructions The information displayed in the above example provides the following information: • First line in display: • The type of event; in this example TROUBL indicating a device trouble • Device type identifier; in this example, SMOKE (PHOTO) indicates a Photoelectric smoke detector.

  • Page 128: Alarm Operation

    Operating Instructions Alarm Operation If multiple trouble conditions exist in the system, they will be automatically scrolled on the LCD display at a three second rate. If a combination of alarms, troubles and/or supervisory conditions simultaneously occur in the system, only the alarms are scrolled on the display. 4.5 Alarm Operation Alarm operation is similar to trouble operation with the following differences: •...

  • Page 129: Supervisory Operation

    Supervisory Operation Operating Instructions • Device Address; 1M001 in this example 1 represents SLC Loop, M represents a module and 001 represents device address 001 4.6 Supervisory Operation Supervisory operation is similar to alarm operation but with the following differences: •...

  • Page 130: Hazard/Tornado Condition Operation

    Operating Instructions Hazard/Tornado Condition Operation 4.8 Hazard/Tornado Condition Operation Hazard/Tornado Condition operation will initiate the following events: • The piezo sounder pulses ½ second On, ½ second Off • The LCD displays a hazard message along with the device name, type, address, adjective/noun, associated zones and time/date •...

  • Page 131: Disable/Enable Operation

    Disable/Enable Operation Operating Instructions 4.12 Disable/Enable Operation Input points which are disabled do not cause an alarm or any zone activation. Disabled output points are held in the off state. All disabled points are treated as if they were in trouble, with the exception being the status label that will be displayed is DISABL.

  • Page 132: Coded Operation

    Operating Instructions Coded Operation Important: When a Notification Appliance Circuit with a mix of audible and visual devices is programmed for silenceable and the synchronization feature is selected, only the audible devices will be turned off if the Silence key is pressed. The visual devices (strobes, etc.) will continue to operate.

  • Page 133: Special System Timers

    Special System Timers Operating Instructions When a detector triggers an alarm, the onboard piezo sounds immediately, but the NACs are prevented from activating for 15 seconds. This inhibit time is factory set and cannot be changed. Pressing the Alarm Silence or Acknowledge/Step key during the 15 second inhibit time will silence the piezo sounder and start a timer which prevents activation of NACs for an additional time duration which can be user programmed for up to three minutes.

  • Page 134: 4: Waterflow Retard Timer

    Operating Instructions Walktest 4.20.4 Waterflow Retard Timer If selected, this option will delay the activation of a waterflow type alarm for a programmable time duration from 1 to 90 seconds. This delay is in addition to any time delay inherent in the waterflow device.

  • Page 135: Read Status

    Read Status Operating Instructions Addressable devices as well as all main circuit board NACs are monitored for fault conditions during Walktest mode. When a new trouble condition occurs, the FACP will activate all NACs and control modules programmed for Walktest, then shut them off after eight seconds. While in Walktest, the trouble relay is activated and the system Trouble LED flashes (as in all of the Program and status change operations).

  • Page 136: 1=System Point

    Operating Instructions Read Status The following screens will be displayed: READ STATUS READ STATUS 1=SYSTEM POINT 1=ANNUNCIATORS 2=ZONES 2=PHONE LINE 3=POWER 3=CENTRAL STATION Read Status Screen #1 Read Status Screen #4 READ STATUS READ STATUS 1=TROUBLE REMINDER 1=SERVICE TERMINAL 2=TIMERS 2=PRINTER/PC 3=NACS 3=PRINT...
  • Page 137 Read Status Operating Instructions Entering the three digit detector address will cause the control panel to display the current status of the selected device. For example, if a detector with address 001 on the SLC loop is entered, a display similar to the following will appear: NORMAL SMOKE(PHOTO) NORTH CLASSROOM Z005...

  • Page 138: 2: Zones

    Operating Instructions Read Status 4.22.2 Zones Pressing 2 while viewing Read Status Screen #1 will cause the following screens to be displayed: READ STATUS 1=SYSTEM POINT 2=ZONES ZONES 3=POWER 1=ZONES INSTALLED Read Status Screen #1 2=ZONES ENABLED 3=ZONES DISABLED Zones Screen #1 ZONES 1=SPECIAL PURPOSE 2=ZONE TYPE...

  • Page 139: 3: Power

    Read Status Operating Instructions 4.22.3 Power Pressing 3 while viewing Read Status Screen #1 will cause the following screens to be displayed: POWER BATTERY 27.21V 24 V RST 25.31 Power Screen #1 POWER CHARGER 28.36V NAC 1 -1.49V NAC 2 -1.49V Power Screen #2 POWER...

  • Page 140: 4: Trouble Reminder

    Operating Instructions Read Status 4.22.4 Trouble Reminder Pressing 1 while viewing Read Status Screen #2 will display the following screen: READ STATUS 1=TROUBLE REMINDER 2=TIMERS 3=NAC TROUBLE REMINDER Read Status Screen #2 TROUBLE REM The screen indicates whether the Trouble Reminder feature is On or Off. 4.22.5 Timers Pressing 2 while viewing Read Status Screen #2 will cause the following Timer screens to be displayed:...

  • Page 141: 6: Nac

    Read Status Operating Instructions 4.22.6 NAC Pressing 3 while viewing Read Status Screen #2 will display the following screen: 1=NAC 1 3=NAC 3 2=NAC 2 4=NAC 4 Note that 3=NAC 3 and 4=NAC 4 will always be displayed regardless of how the NACKEY NAC option card is installed.

  • Page 142: 8: Program Check

    Operating Instructions Read Status 4.22.8 Program Check Pressing 2 while viewing Read Status Screen #3 will cause a screen similar to the following to be displayed: PROGRAM CHECK 1=NACS NO INPUT 2=ZONES NO INPUT 3=ZONES NO OUTPUT Pressing 1 while viewing the Program Check screen will display a screen which will indicate if any input zones have not been programmed to one of the Notification Appliance Circuits.

  • Page 143: 10: Annunciators

    Read Status Operating Instructions 4.22.10 Annunciators Pressing 1 while viewing Read Status Screen #4 will display the following screens: READ STATUS 1=ANNUNCIATORS 2=PHONE LINE 3=CENTRAL STATION ANNUNCIATORS Read Status Screen #4 TERM ENABLED ACS ENABLED UDACT ENABLED Annunciator Screen #1 ANNUNCIATORS 1=ACS ADDRESS Annunciator Screen #2...

  • Page 144: 12: Central Station

    Operating Instructions Read Status 4.22.12 Central Station Pressing 3 while viewing Read Status Screen #4 will display the following screens: READ STATUS 1=ANNUNCIATORS 2=PHONE LINE 3=CENTRAL STATION Read Status Screen #4 CENTRAL STATION REPORTING ENABLED REPORT BOTH CALL LIMIT Central Station Screen #1 CENTRAL STATION 1=PRIMARY 2=SECONDARY...

  • Page 145: 13: Service Terminal

    Read Status Operating Instructions 4.22.13 Service Terminal Pressing 1 while viewing Read Status Screen #5 will display the following screens: READ STATUS 1=SERVICE TERMINAL 2=PRINTER/PC 3=PRINT SERVICE TERMINAL Read Status Screen #5 PANEL ID 2=TERMINAL 1 3=TERMINAL 2 Service Terminal Screen #1 SERVICE TERMINAL RING COUNT Service Terminal Screen #2...

  • Page 146: 15: Print

    Operating Instructions Read Status 4.22.15 Print To print program data or control panel status, press 3 while viewing Read Status Screen #5. The READ STATUS following screens will be displayed: 1=SERVICE TERMINAL 2=PRINTER/PC 3=PRINT PRINT Read Status Screen #5 1=HISTORY 2=WALKTEST LOG 3=DETECTOR DATA Print Screen #1...
  • Page 147 Read Status Operating Instructions Drift Compensation Drift compensation uses software algorithms that identify and compensate for long-term changes in the data readings from each addressable smoke detector. These long-term changes in detector data readings are typically caused by dirt and dust accumulation inside the smoke chamber. Drift compensation performs the following functions: •...

  • Page 148: 16: Time-Date

    Operating Instructions Read Status 4.22.16 Time-Date The operator can view the daylight savings time and the month and week when daylight savings READ STATUS time will begin and end. Pressing 1 while viewing Read Status Screen #6 will display the following 1=TIME-DATE screens: Read Status Screen #6...

  • Page 149: Section 5: Central Station Communications

    Section 5: Central Station Communications The control panel transmits zone and system status reports to Central Stations via the public switched telephone network. Two supervised telephone line connections are made to interface the control panel to the telephone lines. Two optional 7 foot telephone cords are available for this purpose and can be purchased separately.
  • Page 150 Central Station Communications The control panel is capable of reporting detailed messages depending upon the format in use. Table 5.1 shows the reporting structure for all formats. Table 5.1 Format Selection Format Format Format Format Report 3+1/4+1/Standard 3+1/4+1/Expanded 4+2/Standard 4+2/Expanded 4+1 Express 4+2 Express Alarm...
  • Page 151 Central Station Communications Table 5.2 Format Selection Address Explanation Where SSS or SSSS Subscriber ID Alarm (1st digit) Alarm (2nd digit) Zone Number Alarm Restore (1st digit) Alarm Restore (2nd digit) Zone Trouble (1st digit) Zone Trouble (2nd digit) Zone Trouble Restore (1st digit) RTZ2 Zone Trouble Restore (2nd digit) System Trouble (1st digit)

  • Page 152: Transmittal Priorities

    Central Station Communications Transmittal Priorities 5.1 Transmittal Priorities The integral communicator transmits highest priority events first. Events, in terms of priority, are listed below in descending order: Alarms (highest priority level) • Pull stations • Waterflow • Smoke detector • Other alarm types Supervisory Zone System Troubles •...
  • Page 153 Transmittal Priorities Central Station Communications The table below shows UL listed receivers which are compatible with the NFW2-100. Table 5.3 Compatible UL Listed Receivers Format # (Addresses 16 & 42) 4+1 Ademco Express 4+2 Ademco Express 3+1/Standard/1800/2300 3+1/Expanded/1800/2300 3+1/Standard/1900/1400 3+1/Expanded/1900/1400 4+1/Standard/1800/2300 4+1/Expanded/1800/2300 4+1/Standard/1900/1400...

  • Page 154: Section 6: Remote Site Upload/Download

    Section 6: Remote Site Upload/Download The control panel may be programmed or interrogated off-site via the public switched telephone network. Any personal computer with Windows™ 95 or greater, with a 14.4 Kbaud compatible modem and Upload/Download software kit P/N VFWarden-CD, may serve as a Service Terminal. This allows download of the entire program or upload of the entire program, history file, walktest data, current status, system voltages, time and date.

  • Page 155: 1: Security Features

    Downloading Program Remote Site Upload/Download • contact the primary and secondary Central Stations • contact the first available Central Station phone number Once contact has been established, the control panel will report a ‘request for upload/download’ message. Following ‘kissoff’ of the request by the Central Station(s), the control panel will then call the appropriate Service Terminal and begin the downloading process.

  • Page 156: Downloading Initiated At A Service Terminal

    Remote Site Upload/Download Downloading Initiated at a Service Terminal Error Checking As each block of data is received by the control panel, it is checked for accuracy. If an error is detected, the block is retransmitted until correct, up to a maximum of four times. If the Secret Code is not verified and four errors occur, the call is disconnected and the report that the upload/download was not successful is called to the Central Station(s).

  • Page 157: Uploading Initiated At A Service Terminal

    Uploading Initiated at a Service Terminal Remote Site Upload/Download 6.3 Uploading Initiated at a Service Terminal Items that may be uploaded from the control panel to a Service Terminal are: • All programmed data plus the real-time clock, time and date •...

  • Page 158: Section 7: Power Supply Calculations

    Section 7: Power Supply Calculations 7.1 Overview This section contains instructions and tables for calculating power supply currents in alarm and standby conditions. This is a four-step process, consisting of the following: Calculating the total amount of AC branch circuit current required to operate the system Calculating the power supply load current for non-fire and fire alarm conditions and calculating the secondary (battery) load Calculating the size of batteries required to support the system if an AC power loss occurs...

  • Page 159: 2: How To Use Table 7.3 On Page 160 To Calculate System Current Draw

    Calculating the System Current Draw Power Supply Calculations When calculating current draw and the battery size, note the following: • ‘Primary’ refers to the main power source for the control panel • ‘Secondary’ refers to the control panel’s backup batteries •...
  • Page 160 Power Supply Calculations Calculating the System Current Draw Table 7.3 contains columns for calculating current draws. For each column, calculate the current and enter the total (in amperes) in the bottom row. When finished, copy the totals from Calculation Column 2 and Calculation Column 3 to Table 7.4 on page 161. Table 7.3 System Current Draw Calculations Calculation Column 1 Calculation Column 2...

  • Page 161: Calculating The Battery Size

    Calculating the Battery Size Power Supply Calculations 7.4 Calculating the Battery Size Use Table 7.4 to calculate the total Standby and Alarm load in ampere hours (AH). This total load determines the battery size (in AH), required to support the control panel under the loss of AC power.

  • Page 162: Appendix A: Software Zones

    Appendix A: Software Zones A.1 Correlations Setup and configuration of an addressable system is different than a conventional system. In a conventional system, assignment of input devices (smoke detectors, pull stations, heat detectors, etc.) to zones is accomplished through wiring. The wiring is direct from clearly marked panel terminals to any device assigned to a particular zone.
  • Page 163 Correlations Software Zones Correlation of Input and Output Zones Input Devices Zones Output Devices smoke control smoke control ZONE monitor control monitor control control monitor control smoke ZONE control smoke smoke control smoke ZONE smoke control monitor The zone correlations which are shown graphically above are also presented in Table A.1 on page 164 and Table A.2 on page 165.
  • Page 164 Software Zones Correlations Table A.1 Detector Programming Sheet Example DETECTOR ZONE ASSIGNMENT Address Device Zone ADJ/NOUN Address Device Zone ADJ/NOUN Type Number Type Number smoke FIRST HALL smoke ELEV. LOBBY smoke 2ND FLOOR smoke ROOM 210 smoke 3RD FLOOR smoke MEZZANINE smoke MECH.
  • Page 165 Correlations Software Zones Table A.2 Module Programming Sheet Example MONITOR/CONTROL MODULE ZONE ASSIGNMENT Address Device Zone ADJ/NOU Address Device Zone ADJ/NOUN Type Number Type Number monitor monitor 1, 2 monitor 1, 2 monitor control control control control control 1, 2, 3 control control control...
  • Page 166 Software Zones Correlations Table A.3 Blank Detector Programming Sheet - 1 of 2 DETECTOR ZONE ASSIGNMENT Address Device Zone ADJ/NOU Address Device Zone ADJ/NOUN Type Number Type Number FireWarden 100-2/E — P/N 52778:A 11/04/2005...
  • Page 167 Correlations Software Zones Table A.4 Blank Module Programming Sheet - 1 of 2 MONITOR/CONTROL MODULE ZONE ASSIGNMENT Address Device Zone ADJ/NOU Address Device Zone ADJ/NOUN Type Number Type Number FireWarden 100-2/E — P/N 52778:A 11/04/2005...

  • Page 168: Appendix B: Default Programming

    Annunciator Terminal Mode Loop Style Style 4 Annunciator ACS Mode Loop Protocol CLIP UDACT Trouble Reminder ACS Installed Banner Honeywell Life Safety Onboard DACT Time Format 12 Hr Printer-PC Hours Setting Printer Baud 9600 Minutes Setting Second Settings AM-PM Setting...

  • Page 169: Appendix C: Nfpa Standard-Specific Requirements

    Appendix C: NFPA Standard-Specific Requirements The NFW2-100 has been designed for use in commercial, industrial and institutional applications and meets the requirements for service under the National Fire Protection Association (NFPA) Standards outlined in this Appendix. The minimum system components required for compliance with the appropriate NFPA standard are listed below: NFW2-100 Control Panel Contains the main control board, cabinet (backbox and door), main power supply transformer and...
  • Page 170 NFPA Standard-Specific Requirements FIRE Municipal Box Circuit Gamewell Model M34-56 Local Energy Municipal Box Polarities shown in alarm condition Nonpower-limited 4XTM Figure C.1 Municipal Box Connected to 4XTM Transmitter Module FireWarden 100-2/E — P/N 52778:A 11/04/2005...
  • Page 171 NFPA Standard-Specific Requirements NFPA 72 Remote Station Protective Signaling System Notes: Cut Jumper JP3 on the NFW2-100 main circuit board to supervise placement of the 4XTM module. Refer to “4XTM Transmitter Module Installation” on page 34 for detailed information. RS82 Remote Station Receiver UL listed. Refer to Instruction Manual for Remote Station Receiver Model RS82.
  • Page 172 NFPA Standard-Specific Requirements NFPA 72 Proprietary Protective Signaling Systems NFW2-100 Addressable Fire Control Panel NFW2-100 Main Board Form-C Alarm contact programmed to activate on General Alarm. Form-C Trouble contact which will automatically activate on any Trouble condition. Form-C relay contact programmed to activate on Supervisory condition.

  • Page 173: Appendix D: Wire Requirements

    Appendix D: Wire Requirements T-tapping of the SLC loop wiring is allowed for 2-wire (Style 4) configurations. The total resistance of any branch cannot exceed 40 ohms. The total wire length of all branches cannot exceed 10,000 feet (3,000 m). Connecting external system accessories to the NFW2-100 main circuits must be carefully considered to ensure proper operation.

  • Page 174: Appendix E: Hvac Control

    Appendix E: HVAC Control The FACP can be programmed to shut down a building’s HVAC fans in the event of a fire. The fans cannot be restarted until the fire alarm condition has been cleared and the FACP has been reset to a normal (non-alarm) condition.

  • Page 175: E.2.2: Hvac Ovrride

    Monitor Module Operation HVAC Control E.2.2 HVAC OVRRIDE The HVAC OVRRIDE type code can be assigned to any addressable monitor module for the purpose of overriding or preventing the HVAC SHUTDN control modules from activating and shutting down fan during an alarm or manual evacuate condition. The HVAC OVRRIDE monitor module acts globally throughout the FACP system and therefore is not programmed to a particular software zone.
  • Page 176 Index Numerics Alarm Silence 15 alarm verification 12 24 Hour Test Time 102 annunciator 19 4XTM module 170 ACM-8R 12 coil resistance 34 ACS 12 current 34 FDU-80 12 installation 34 LDM Graphic 12 installation steps 35 annunciator addressing 38 see also Transmitter Module 12 annunciator, graphic voltage 34...
  • Page 177 Index D–E CHG-75 Detector see also battery charger 19 add 45 see also remote battery charger 13 adding description 51 Clasic Loop Interface Protocol 76 delete 46 Class A 28 edit 46 Class B 28 enable/disable 48 NAC wiring 30 screen display 47 Clock Format 80 type 49...
  • Page 178 F–N Index Kiss-off 125 Maintenance 125 FACP Primary Line Active 125 see also Fire Alarm Control Panel 11 Secondary Line Active 125 FDU-80 annunciator 12 see also Indicators 15 Features 11 Supervisory 125 Fire Alarm Control Panel Trouble 125 see also FACP 11 LED annunciator 19 Format Selection Address 150 Local Energy Municipal Box Service 34...
  • Page 179 Index O–P Style configuration 29 annunciators/UDACT 93 Style Y wiring diagram 30 Printer/PC 112 synchronized 131 Options 11 type codes 85 Output Circuits 16 voltage drop 13 voltage, operating 13 wiring Style 28 Panel ID 96 NAC enable/disable 84 Panel Identification Number 155 NAC options 77 PAS 50 NACKEY card 29...
  • Page 180 R–S Index clear 113 Remote Station Service 35 Program Check remote switch functions 12 Maintenance Level 118 remote sync output 13 program keys Remote Synchronization 31 see also Key Panel 15 Programming 39 see also Ringer Equivalence Number 21 autoprogramming 40 Report Style 111 exiting 40 Reporting Enable 98...
  • Page 181 Index T–Z NAC wiring 30 monitor module 59 NC configuration 29 NAC 85 Style Z 28 type code NAC configuration 29 control module 67 wiring 30 supervision 131 subscreen 41 verification 12 Supervisory 129 supervisory relay configuring for 4XTM 36 UL power-limited wiring requirements 32 sync see also power-limited and nonpower-lim-...
  • Page 182 Z–Z Index Zone 98 73 Zone Assignment 51 control module 67 Zone Setup 72 Maintenance Level 121 zone type 75 list 75 Zone Z97 50 Zone Z98 pre-signal zone 50 Zones 138 see also software zones 11 Zones Disabled 74 Zones Enabled 74 Zones Installed 74 zones per device 51...
  • Page 183 Limited Warranty NOTIFIER® warrants products manufactured by it to be free from defects in materials and workmanship for eighteen (18) months from the date of manufacture, under normal use and service. Products are date stamped at time of manufacture. The sole and exclusive obligation of NOTIFIER®...
  • Page 184 World Headquarters NOTIFIER is a Honeywell company. 12 Clintonville Road Northford, CT 06472-1653 USA 203-484-7161 fax 203-484-7118 www.notifier.com...

This manual is also suitable for:

Notifier firewarden-100-2e

Table of Contents